What happens if your GMC Sierra has low oil pressure?

One of the most serious issues that can happen to your GMC Sierra ‘s engine is if it ends up with low oil pressure. Low oil pressure will cause the engine to seize up. When the oil pressure light on, it should be assumed that the engine locking up is imminent. We advise not running the engine until the issue can be properly diagnosed.

Why does my GMC Acadia have a low stop light?

My car is 2010 GMC Acadia I see warning light oil pressure light low stop engine so I check oil level and it seems good and heat not increase also Is this a good question? Naif, Heather M , It very well could be a bad oil pressure sending unit/sensor, but better to be safe then sorry and have it checked out right away.

Can a low oil pressure cause engine to seize up?

Low oil pressure will cause the engine to seize up. When the oil pressure light on, it should be assumed that the engine locking up is imminent. We advise not running the engine until the issue can be properly diagnosed. There are many things that can cause low oil pressure.

What to do if your oil pressure is low?

If the engine oil level appears to be low (or empty), you’ll need to fill it up. Do not drive a vehicle with low engine oil to the store to buy more oil. Running without enough oil to keep pressure in the crank case will certainly look up the engine.

What kind of lifters does a 2008 GMC Sierra 5.3 have?

Just did the vlom and afm lifters on my 2008 gmc sierra 5.3. took it for a test drive with the old oil and filter for a run up before the oil change. It made it 3 kilometers with full oil psi then it dropped to zero.

What causes the oil pressure to fluctuate?

When you spin a pump faster it puts out more fluid. The oil in your engine is circulated with a PUMP. Increasing the RPM of your engine spins the pump faster. The friction induced by the flow of oil through the engine makes it more difficult for the pump to output this increased volume of fluid.

What should my oil pressure be when I start up my truck?

Whenever I start it up, the gauge jumps right up to around 40, and stays there, which seems like its normal operating pressure. However, whenever I rev the engine, the pressure gauge responds to my acceleration by going UP.

What’s the oil pressure on a GM Truck?

After my truck warms up the oil pressure drops and the check gauge light illuminates. When the engine is cold at start up the pressure gauge reads 30PSI plus. After it warms up and at a stop in drive the pressure will drop to approx 5 PSI and will even dip to 1 or 2 PSI.

Why does my oil pressure drop when I come to a stop and?

When I come to a stop the oIl pressure goes down to almost nothing and the red check gauges light comes on. Once I drive off, the check gauges light goes off and the oil pressure goes back to normal. Because the oil pump is engine driven. As the engine speed goes down, the oil pump output pressure decreases.

What should oil pressure be after changing oil sending unit?

OIl pressure still drops after changing oil sending unit? When truck is first started, oil pressure is normal, around 40 psi. When engine temp starts up, oil pressure slowly falls until “Stop Engine – Low Oil Pressure” warning comes on. Switch truck off a few second, maybe 20-30, restart truck and back to 40. And on and on.

How to fix oil pressure drop on GMC Sierra?

Part 2 – YouTube Oil Pressure Drop Fix 08-14 GMC Sierra. Part 2 If playback doesn’t begin shortly, try restarting your device. Videos you watch may be added to the TV’s watch history and influence TV recommendations. To avoid this, cancel and sign in to YouTube on your computer. An error occurred while retrieving sharing information.

How can I tell if oil pressure is low in my car?

Step 1 – To verify the engine oil pressure is low, start the engine (cold) and observe the gauge or light. Step 2 – Using the engine oil dip stick, check the oil level of the engine and ensure a proper level.

Can a bad oil pressure sensor cause a bad engine?

Naif, Heather M , It very well could be a bad oil pressure sending unit/sensor, but better to be safe then sorry and have it checked out right away. If you hear any noises from engine knocking/ticking or if engine is not performing as usual discontinue starting/driving vehicle as there could be a major problem internally of engine.

How to check oil pressure in Chevy 5.3?

1 Locate the oil sending switch or unit. 2 Unplug the electrical connector sending unit. 3 Connect the gauge’s hose with the correct fitting so that it helps to plug the indicator in the sending unit. 4 Start the engine and allow it to reach operating temperature, keeping it idle for 20 minutes.

What should the oil pressure be in a Vortec?

But after the engine warmed up, the oil pressure dropped below normal at idle and the engine noise (probably lifters) returned. Raising the engine speed to above 1000 rpm causes the oil pressure to increase to about 45 psi. If the engine speed is increased even more, oil pressure tops out at about 55 psi.

What should fuel pressure be on GM 4.3L Vortec?

You can find this tutorial in Spanish here: Cómo Probar La Bomba de Combustible (GM 4.3L, 5.0L, 5.7L) (at: autotecnico-online.com ). The fuel system in your 4.3L, 5.0L, or 5.7L Vortec engine needs at least 50 PSI of fuel pressure to start.

How to check fuel pressure while cranking engine?

TEST 1: Checking The Fuel Pressure Specification. So, the very first thing you need to do is to verify that the fuel pump is delivering at least 50 PSI of fuel pressure while the engine is cranking. Yes… while the engine is cranking. Locate the Schrader valve on the fuel line that connects to the ‘Spider’ assembly.

What should the fuel pressure be in a CPI system?

Fuel pressure in the CPI system with the key on and engine off (KOEO) should be about 58 to 62 psi. Some specs say 54 to 60 psi is OK, but some fuel injection experts insist that to start and run properly, most CPI systems really need at least 58 psi. Pressure is generated by a tank-mounted electric fuel pump.

What should the fuel pressure be on a 1998 Chevy Silverado?

Fuel Pressure Specification The fuel pressure specification for the 1998 Chevrolet Silverado truck is from 55 to 61 lbs. per square inch (psi) for models equipped with the 4.3-liter V-6. Trucks with either the 5.0-liter or 5.7-liter V-8 should have fuel pressure between 60 and 66 psi.

Can a low oil pressure cause an engine to misfire?

There is a relation between engine misfire and low oil pressure because the sudden drop of oil pressure can cause the engine not running right and the RPMs to drop low in gear causing an engine misfire.

Why does my car have low oil pressure at idle?

Car owners often forget to check their engine oil level. If your engine is low on oil it can cause low engine oil pressure at idle because there won’t be a sufficient amount of oil to circulate and lubricate the engine. This can lead to serious engine damage due to lack of lubrication. I check my engine oil every 2 weeks.

Is it OK to drive an engine that is misfiring?

Instead from that, misfires can damage other sensors in the engine like the O2 sensors. So, I would never recommend driving an engine that is misfiring for any long distances. Short distances to your mechanic workshop without putting a load on the engine is fine, but do not ignore the misfires and keep driving.

Why does my GM V8 engine misfire when cold?

Because, GM V8 engines are very prone to a rough idle and engine misfire when cold. The check engine light may also come on, with codes P0300, P0171 and PO174. But, as the engine warms up, the engine misfire or rough idle tends to go away; which seems confusing.

Is there an engine misfire code on a GM 4.8L?

Engine Misfire or Rough Engine Idle on GM 4.8L, 5.3L, 6.0L is becoming; more common and getting harder to diagnose. Because, GM V8 engines are very prone to a rough idle and engine misfire when cold. The check engine light may also come on, with codes P0300, P0171 and PO174.

Can a bad fuel pressure regulator cause a misfire?

There are also many causes of engine misfires. It can be a problem in the spark plug or the ignition coil. A fuel injector problem can also cause engine misfires. It is also one of the symptoms of a bad fuel pressure regulator. A problem with this device can lead to low fuel pressure.

How to troubleshoot a GM Truck misfire?

This isn’t the only symptom that your GM van, pickup or SUV might experience… here are some more that you might see: P0300: Random Cylinder Misfire. P0301: Cylinder #1 Misfire. P0302: Cylinder #2 Misfire. P0303: Cylinder #3 Misfire. P0304: Cylinder #4 Misfire. P0305: Cylinder #5 Misfire. P0306: Cylinder #6 Misfire. P0307: Cylinder #7 Misfire.

What should the oil pressure be when the engine is cold?

When the engine is cold at start up the pressure gauge reads 30PSI plus. After it warms up and at a stop in drive the pressure will drop to approx 5 PSI and will even dip to 1 or 2 PSI. Oil being used is 10W40. Idle is a little rough but not too bad. Engine does not burn oil.

What’s the oil pressure on a Silverado 2500HD?

My 01 2500HD (145k~ miles) has about 40-45 PSI idle, and anywhere from around 55 to 70PSI running around. It might hit 75+ at WOT. This is according to the cluster, so it may be off a bit, I don’t know.

What kind of oil for GMC 6.0 2500 HD?

My truck is being built now {GMC 6.0 2500 HD} Go to the synthetic right at the first oil change. There is no real “break in” on engines nowadays as there was in days gone by. there are many engines that come right out of the factory with full synthetic. Dexos1 GM approved oil are all synthetic blends or full synthetics now.

What is the normal oil pressure for 6.0?

I have a 2002 Chevy Silverado 1500 hd 6.0 v8 and I am wondering what the normal oil pressure is at idle and cruising. I don’t have a 6.0 but my 153,000 mile 1999 5.3 liter motor idles with 35 PSI hot and about 45 PSI hot while driving at moderate speeds.

What was oil pressure in 2003 2500HD 6.0L?

2003 2500HD 6.0L with about 105k. Got in the truck this morning to go to work and the low oil pressure warning came on and gauge was basically at zero. Figured it was just the gauge so cycled the key a few times and still zero pressure. Limped around the block and started to hear a light knock so shut it down.

What’s the normal oil pressure for a Silverados 6.0?

About 165-170 PSI for compression across all cylinders and the spark plugs burn cleanly with good color. The bottom end of this engine has never been touched and the motor is doing well other than needing a few top end engine sensors replaced – engine coolant temperature, camshaft position sensor, both knock sensors and harness.

What should the oil pressure be on a Vortec 6.0?

If it seems low, change the sensor. If it seems high, change the sensor. If it seems just about perfect all the time , yep your sensor is probably stuck, so change the sensor. badbruin44 wrote: The oil pressure on the Vortec 6.0L engines seem all over the place mine seems low like about 20 PSI idling and about 40 PSI cruising down the road.

Why does my oil pressure drop to zero?

Just went through this with a 2002 sierra 5.3, Pressure would randomly drop to zero and if I did not kill the engine fast ehough I would get a bad lifter tap so it was definitely not a bad sensor/sending unit. Even though the truck had extremely low mileage and oil changes were routinely done sediment had built up in the engine.

How can you tell if your oil pressure is too low?

Oil pressure gauge reading too low, generally below 15 to 20 PSI while idling. Cold weather can also make the oil pressure read low until the oil pump has had a chance to deliver the oil to the engine. Oil pressure gauge reading too high, or over 80 PSI while driving, especially at higher RPMs.

What should the oil pressure be at 3000 rpm?

The ideal oil pressure ranges between 25 to 65 psi when the engine oil is warm and 1000-3000 rpm, whereas if the oil pressure reading shows 80 psi or above then there is some serious problem.

How to check the oil pressure in a Chevy Silverado?

As soon as it drops again pull over shut it off immediately pop the hood and check the oil. Nearly every drop should be in the pan and ready to read only seconds after shutting it off. That will tell you if its getting stuck above the heads.

What is normal oil pressure at 2000 rpm?

Going to have 10W40 put in it. 5.3L normal pressure, book says, at 2000 RPMs is 20PSI. That seems low but he said Chevy are low compared to engine makers. Running down the road today, engine hot, at 2000 rpm gauge said about 20 psi.

What causes the oil pressure to drop in a Chevy 5.3?

The worn-out parts allow the oil to get into the combustion chamber, and it gets burned, thereby causing the engine oil pressure and oil to drop. There will be a cloud of blue smoke coming out of the tailpipe, and the fuel dilutes engine oil. This results in a drop in oil pressure.

What’s the oil pressure on a 1999 Chevy Z71?

I have 5.3L V8 in a 1999 Chevy Z71 Pick up, 131,000+ miles, automatic. Oil was changed about 2,000 miles ago, 5W30, I have been told. Well last weekend I put about 300 miles on it and about 2,000 RPM the dash gauge (oil) would indicate 40 PSI, today it was down to about 20-25 PSI. Today idle is only about 10 PSI ( The engine is hot).

What’s the oil pressure on a 2015 Silverado?

I have 2015 HD Silverado 4×4 with the 6.0 gas motor. It has 218,000 miles on it. I’ve kept up with oil changes religiously. Today I get in it and notice going down the highway I’m only at 20 pounds of oil psi. Pull over, at ten psi at an idle. Checked the oil & it’s full and clean as usual.

Why does the oil pressure light come on on my GMC Truck?

Light came on due to a red area reading. Appreciate the response. I’ll start there and see what happens. Update when you figure it out. If it happened all of a sudden it could be that sending unit or the gauge itself. I ran lucas in my truck one time to get rid of a knock and my pressure shot up to 80 at all times.

What kind of oil does a GMC Silverado have?

Truck is a 2003 Silverado with approx. 110,000 on it. Yep. First thing to look at. Do check your oil, of course, but I’m sure that’s fine. Light came on due to a red area reading.

What should the oil pressure be in a Chevy truck?

When the truck is at warm idle the pressure should be within this range: 25 – 40 PSI When you are driving at speed the pressure should be within this range: 40 – 70 PSI

What should the oil pressure be on a Silverado 2500HD?

Use top quality such as Napa Gold, Wix, Baldwin. Forget the Lucas. You might try 10w40 oil, depending upon your climate. Yeah, what should oil pressure be at idle on an 2004 2500hd with 6.0l. 25-30 at idle would be great. 40+ with rpms.

What’s the oil pressure on a Chevy 6.0L?

Oil pressure now is at 35 on startup, falls to 18-20 on idle. And moves up slightly while driving with regard to rpms, but rarely/if ever, goes above 40psi no matter how high the rpms.

What does the oil pressure low stop engine message mean?

The Oil Pressure Low – Stop Engine message appears when the oil pressure switch, which is located on the engine, has detected low oil pressure.

What to do if your Chevy Tahoe has low oil pressure?

DO NOT leave the extra 2 qts of oil in the engine, it would not be good. To determine if the pickup tube o-ring is bad, add 2 extra qts of oil to the engine. If there’s a leak at the o-ring it will now be submerged. Start the engine, let it idle, and see if the problem goes away.

What are the problems with an oil pump?

Problems with the Oil Pump: Any sort of air leakage in the supply side of the oil pump will also cause cavitation (back pressure) and loss of oil pressure. The engine builder should check the supply side of the oil pump and make any necessary repairs. The other common issue with the oil pump is excess wear to the gears.

How is the oil pump on a Chevy Tahoe secured?

It is secured with 2 12mm bolts to the bottom of the engine and 1 10mm bolt up front to the actual oil pump. Don’t strip any of these, if you can. Especially the one up front as it is in a tight location. Take your time. 12) With pickup tube out, you will see the gasket that needs replacing.

What causes an engine to lose oil pressure as it warms up?

The most likely cause of a car losing oil pressure when it warms up is a problem with the pressure relief valve, which regulates the oil pressure to ensure that there is enough pressure to circulate oil throughout the engine. When oil pressure is low, not enough oil is being distributed to the engine, potentially causing engine failure.

What should I do if my oil pressure is low?

Loss of engine oil pressure is a serious yet common matter with diesel engines. It should be noted that ignoring a low oil pressure warning could result in serious damage to your engine. The best way to keep your engine running is to regularly change the oil and keep the internal parts properly lubricated.

What happens when oil pressure is too high?

The faster the engine moves, the higher the rate of oil flow and the higher the pressure. Too much pressure can be damaging to engine components, though. A relief valve close to the oil pump opens when the pressure reaches a predetermined value, usually between 45 and 75 psi, allowing extra oil to drain back into the oil pan.

What is normal oil pressure for a 2008 5.3L AFM?

What is normal oil pressure for a 2008 5.3L AFM? At cold idle I’m over 40 (can’t remember exactly where), maybe around 50 psi. When driving cold it’s around 50 psi or so. When it warms up and driving I’m right at 40 psi or slightly above and maybe right at or slightly under 40 psi at idle.

Why does my GM 5.3 liter engine burn oil?

The TSBs indicate the problems are caused by PCV issues, piston rings and the active fuel management system. GM redesigned its 5.3-liter V8 engine after the 2014 model year, using redesigned piston rings and adding a shield to deflect oil away from the piston skirts.

When did GM change 5.3 liter V8 engine?

GM redesigned its 5.3-liter V8 engine after the 2014 model year, using redesigned piston rings and adding a shield to deflect oil away from the piston skirts. The newer versions of the engine also feature an oil level sensor and new valve covers. Vehicles involved in this class action were all built between 2010 and 2014.

Why does my 5.3 liter engine have low oil pressure?

This is one of the common 5.3 Liter Chevy Engine Problems but it mostly occurs in the older models. So, if you are running an older engine, keep this in mind. However, if you believe there is a real problem, have a look at the potential causes below: This is the common cause of low oil pressure.

What’s the low oil pressure warning on my truck?

Truck has been more or less trouble free thus far. I dropped my truck off for some body work 3 long weeks ago, and shortly after getting it back, it gave me a “low oil pressure – shut engine down immediately” warning. The oil pressure went from ~35psi down to ~20psi and then slowly tailed off to 0psi.

What should oil pressure be on a 5.3 liter Chevy?

Good oil pressure on the 5.3 Chevy is said to be anything from 25 PSI and above at hot idle and with new engine oil. If oil pressure shows 21 PSI or below that with new engine oil, then the pressure is low, and damage could occur.

What kind of oil does a GMC Sierra use?

There IS a screen below the oil pressure sending unit that does become clogged!! I have an 07 GMC Sierra, 4×4 Crew Cab, SLE2 package, 144,000 miles. 5.3 litre. I change my oil faithfully at 3000 mile intervals, use Castrol GTX High Mileage oil and Purolator oil filters. Air filter gets replaced every other oil change.

Why does my oil pressure go down when I start the car?

If the valve is absent, the oil supply passages inside the engine lose their oil. It will take a few seconds for the oil pump to fill the supply passages back up after the engine starts. Expect that problem to be worse in the mornings, after the car sits overnight. Install the correct oil filter and the problem should be fixed. Simple.

What should the oil pressure be on a Chevy Silverado?

Check the voltage to the gauge it should be a steady 12-13.5 volts. — A oil pressure gauge in actually a voltage gauge with a different face. 12 volts on the supply side and the sending unit actually varies the resistance to ground.

What’s the oil pressure on a 2010 Silverado?

I have a 2010 Silverado 5.3L. I notice every so often on start up a noise like the oil pressure is low and the lifters are knocking, it last about 40 seconds or so even on warm mornings. While driving the oil guage reads around 40 (guess I’m still in the rut of old school where oil pressure is 60 and you use 10w-40).

What kind of oil does a GMC Sierra take?

I’ve got a 2010 Sierra with the 5.3 AFM. Its got 107,000 miles, just over 3,000 miles on last oil change. Pennzoil platinum 5W-30. Oil in the correct range on the dipstick.

What should the oil pressure be in a truck?

When truck is first started, oil pressure is normal, around 40 psi. When engine temp starts up, oil pressure slowly falls until “Stop Engine – Low Oil Pressure” warning comes on. Switch truck off a few second, maybe 20-30, restart truck and back to 40.

Is the oil pressure on the Dodge LMM accurate?

The oil pressure gauge on the lmm is actually dead on accurate. The Dodge gauge is more like an idiot light. Itll be in the middle until you have no oil pressure then it’ll drop to zero. Think about it, its a pump that changes rpm with the engine, of course pressure will fluctuate. It does with all engines.

What should the oil pressure be on a Chevy Duramax?

Lb7 – 15w, 80lbs on start up at 20°. Then at temp about 30 according to the gauge. These are high volume low pressure pumps. Lb7 – 15w, 80lbs on start up at 20°. Then at temp about 30 according to the gauge. These are high volume low pressure pumps.

Where is the oil pressure on a Dodge?

The Dodge gauge is more like an idiot light. Itll be in the middle until you have no oil pressure then it’ll drop to zero. Think about it, its a pump that changes rpm with the engine, of course pressure will fluctuate. It does with all engines. Its just a matter of how accurate the stock gauge is.

Is it normal to have no oil pressure after starting an engine?

If the engine is running on idle after starting the will no oil pressure build. After kicking the engine the motor has oil pressure in idle. Is this normal????? I let you know if the engine will run prefectly.

How can I tell if my oil pressure sensor is failing?

This is a common sign of a failing oil pressure sensor. This is a small unit in the engine block that reads oil pressure inside the motor and relays this information to the vehicle’s computer as well as the oil pressure gauge.

Is it normal for the oil gauge to read 0?

When the engine not running it is normal for it to read 0 since the oil pressure is created by the engine running. To have this corrected, I would recommend having a certified professional from YourMechanic diagnose the odd oil gauge behavior and assist with repair.

What should the oil pressure be on a Chevy 5.3?

This is cause to investigate further because damage can occur when the pressure is too low. Furthermore, if you are reaching 80 PSI with your oil pressure reading, this is also cause for alarm. For exact specifications, you may want to consider the repair manual for your model and make.

How does a Chevy 5.3 oil pump work?

The oil pump work is to push oil under the galleries and bearings through narrow clearances. In the narrow passages, the pressure is built in the system to restrict the oil flow rate.

Is the traction control light on on my GMC Serria?

1,593 satisfied customers It is a GMC 2013 1500 4×4 sierra and the abs light is on the It is a GMC 2013 1500 4×4 sierra and the abs light is on the traction control light is on and it says service stabilitrak and service traction control. it happened about a year ago and they replaced t…

Where is the oil pressure screen on a GMC Sierra?

The oil pressure sending unit and screen are at the back top of the motor, under the intake manifold, on top of the afm manifold. I have an 07 GMC Sierra, 4×4 Crew Cab, SLE2 package, 144,000 miles. 5.3 litre. I change my oil faithfully at 3000 mile intervals, use Castrol GTX High Mileage oil and Purolator oil filters.

How many GM trucks have oil pressure issues?

From buying research to owner support, join 1.5 MILLION GM Truck Enthusiasts every month who use GM-Trucks.com as a daily part of their ownership experience. For those of you that have noticed oil pressure drops, etc.

How to reset the oil change light on a 2001 Chevy Silverado?

Insert your key into the 2001 Chevy Silverado ignition. Turn your key two clicks forward into the RUN position. Verify that your dashboard lights, radio and odometer turn on. Your 2001 Chevy Silverado engine should not start. Push and release the accelerator pedal fully three times within five seconds while monitoring the dashboard lights.

What kind of oil pressure does a GMC Yukon have?

Hello – battling low oil pressure on a 2011 GMC Yukon XL Denali (6.2) w/ 175k miles. Very well maintained, does not burn or leak oil. got oil pressure warning – replaced sending unit (there was not a …

Can a Chevy Silverado 1500 oil pressure sensor go bad?

10 people found this helpful. have your oil pressure checked with gauge, possible oil pressure sensor back by the distiributor going bad and also therse trucks are bad that the instrument cluster goes bad, gm had a extended warranty on them to 100,000 miles or 7 years 32 people found this helpful.

How does the Check Engine oil level light work?

Just like the windshield washer level indicator, it is only a mechanical switch. When liquid is added and the level rises, the switch turns off. You have damaged the contact/wiring/plug and the level system is indicating low. that is what I believed originally, Ray, but wanted to be sure. Are you aware of any dedicated fuse for that function?

Why does my Yukon Denali have low oil pressure?

Unfortunately, yes. If there are metal shavings, this is a sign of worn bearings. It could also be a sign of a failing Oil Pump. Both of which will give low oil pressure.

Why do I need an oil change on my GMC?

An oil change, which drains old oil and replaces with fresh new oil, helps to keep an engine properly lubricated. Years ago, engine oil changes were typically prescribed at a set interval, which was usually based upon mileage.

Why do you need an oil life monitor on a GMC?

Knowing when to change your oil is incredibly important, and the Engine Oil Life Monitor, found in most new GMC models, not only helps owners keep their GMC properly maintained, but also maximize their maintenance investment. An engine contains thousands of moving parts, like valves, pistons, camshafts, and so on.

When to get an oil change on a GMC?

When your vehicle is ready for an oil change, GM has a standard list of inspection for servicing your GMC: GMC also recommends these scheduled maintenance items throughout the life of the vehicle: After your oil change and servicing is complete, you might need to reset the OLS system in your GMC.

What’s the oil pressure on a Chevy Silverado 5.3?

My 5.3 is normally at 40-41 psi at idle. It was low at about 26 ish. Today when I was driving it suddenly went to 80psi and at idle around 76. When I turned the truck off and just turn the key on it goes up to about 43psi. But when starting up shoots back up to 80 psi. When key is off it goes back down to 0psi.

Where is the oil pressure sensor on a Silverado?

It is on the top of the block on the driver side behind the intake manifold and has a wire connector plugged in to the top of it. It is more likely the sender and not a stepper motor, especially if all the other steppers are working correctly. Plus, it is much easier to change the sensor than a stepper motor. Went and bought a sending unit.

What’s the oil pressure on my GMC Sierra?

I have a 2012 GMC Sierra with only 20k miles on it… this morning “Low Oil Pressure, Stop Engine” came on. I pulled over and restarted with no further issues. On the way home the check engine light came on. It says Oil Life is at 18% and when car is turned off the oil pressure is 3 PSI (is that normal?!).

When to change oil in Silverado Sierra GMC?

My friends 2010 runs about 40 psi after he changes his oil (synthetic) , he says when his oil pressure starts dropping real low he knows it time to change oil .. He says his low oil pressure light will come on sometimes . Usually under 5000 miles. This is were the they say it should be.

What’s the oil pressure on a 2004 Silverado?

I replaced the pressure relief under the oil fitter and the oil pump. The truck has 200,000 miles on it but runs great. At idle the pressure is still around 5 when hot and 20 cold. When reved it goes to 40 cold and 20 hot. Lucas stopped the lifter noise.

What’s the Check Engine light on my 2013 Silverado?

A week ago I got a check engine light in my 2013 Silverado with the 5.3. I scanned the code and it was a oil pressure code.

What kind of oil pressure does a Silverado have?

I have a 2010 Silverado with a 5.3 with about a 100000 miles on it .it has given me low oil pressure warnings off and on over the past few years . it has good oil pressure otherwise it would have blown up by now.

A week ago I got a check engine light in my 2013 Silverado with the 5.3. I scanned the code and it was a oil pressure code.

Why does my oil pressure read high on my Silverado?

If your 2003, 2004, 2005 or 2006 Silverado oil pressure gauge pegged out, has unusual fluctuations in it’s readings or reads high it can be caused by one of two problems. The first common cause is a faulty oil pressure sensor which is mounted on the engine. This is yet another common issue with 03-06 Silverados.

What to do if your fuel gauge is not working?

The first place to start is to check the ignition 12 volt power feed at the fuel gauge to see that it is powered up. If you DO NOT have 12 volts ignition on the fuel gauge, check the gauge fuse to see if it is good, and make sure the ignition switch is powering the ignition pink wire on the ignition blade…

When to know if your oil pressure gauge is faulty?

It alerts you when there’s a real problem going on in your engine. It is your indicator when your engine is running low on oil or when it is overheating, and if these problems go unaddressed, it could mean engine failure and hefty repair costs. That’s why it is important to understand when your oil pressure gauge is faulty.

Why does my Chevy Tahoe have no oil pressure?

This feature is not available right now. Please try again later. If the oil pressure gauge in your Chevy Silverado, Avalanche, Tahoe, or Suburban is reading no oil pressure, excessive oil pressure, or if the oil pressure gauge is simply bounching around or not working then this may be your fix.

Why is my oil pressure so high when I am not driving?

The gauge should never read very high when you’re not driving because the engine should be fairly cool due to inactivity. If you park or idle your car after driving and your pressure gauge reading does not return to a lower number, the gauge is defective. There are many reasons why an oil pressure gauge may be broken.

Can a bad oil pressure sensor cause low oil levels?

An Oil Pressure Warning Light will often accompany oil pressure sensor faults. Like any other sensor or switch in your engine, eventually the oil pressure sensor will have repair issues that need to be addressed. Failing to recognize the symptoms of a bad oil pressure sensor can lead to low oil levels, which can be very problematic for your engine.

How can you tell if your oil pressure unit is failing?

Oil Pressure Reporting Erratically This is perhaps the most telltale sign of a malfunctioning sending unit. If your oil pressure gauge or engine oil warning light have very sporadic behavior—the gauge moving from low to high or high to low randomly or the light coming on and off frequently—you can be sure there’s a problem with the sending unit.

Like any other sensor or switch in your engine, eventually the oil pressure sensor will have repair issues that need to be addressed. Failing to recognize the symptoms of a bad oil pressure sensor can lead to low oil levels, which can be very problematic for your engine.

What does it mean when your oil pressure is low?

When the oil pressure is low, it means that the engine is not getting the needed lubrication and this can lead to serious engine damage. Once you see the low oil pressure light illuminated, do not drive your vehicle until the issue is fixed. Here are the most common causes of low engine oil pressure: 1. Low Engine Oil Level

Why is the oil pressure so low in my Vortec?

Raising the engine speed to above 1000 rpm causes the oil pressure to increase to about 45 psi. If the engine speed is increased even more, oil pressure tops out at about 55 psi. Given the mileage on the vehicle, I’m wondering if the lower-than-normal oil pressure at idle is due to internal engine wear.

What does a low oil level sensor mean?

However, this symptom should not be avoided. This warning sign could indicate a problem with the engine’s oil pressure or that the oil lines are blocked by debris. If this symptom comes up, it should be taken very seriously, as low oil pressure or blockage in the lines can result in complete engine failure.

How do you reset the oil life on a GMC Sierra?

Follow the instructions below to reset the engine oil life system on your GMC Sierra: Don’t start the engine! Done! For all models, the oil life system can also be reset as follows: Turn the ignition to ON position without starting the engine. Fully press and release the accelerator pedal 3 times within five seconds.

How much oil should I put in my GM Sierra?

First off, the General Motors standard for acceptable oil usage in the Sierra is 0.946 liter every 3200 km. If you notice that your truck is regularly running above that (or it just feels high to you) it’s can never hurt to make an appointment at your local shop for an oil consumption test.

Is there a solution for 5.3 GM engine burning oil?

While having performance affecting flaws in your vehicle can be frustrating, know that there are solutions for the 5.3 GM engine burning oil that can keep your pickup running smooth (and don’t require you to start shopping for that brand new Sierra ).

How to replace GMC k1500 oil pressure switch?

Your body type? If playback doesn’t begin shortly, try restarting your device. An error occurred. Please try again later. (Playback ID: QKNnL57sW1HYYF0s)

What should I heat my GMC Sierra 1500 with?

You’ll need to heat the tranny pan for sure and maybe the lines and cooler to get it to move. Drag would be the fastest. Rent a large tarp and a hermon nelson type heater (works good 2 to 3 hrs at -30 and you should be moving).

Why does my GMC Sierra 1500 not work?

If it ran good, you parked it, it got f’in cold and now it doesn’t work maybe you have some water in the system, a line may be frozen (never heard of this though). On the passenger side of the tranny there are the two coolant lines. The top port is the coolant return bottom is the tranny output. Follow them up to the rad or external tranny cooler.

Where are the coolant lines on a GMC Sierra 1500?

You should see the cable rotate the shifter. If it ran good, you parked it, it got f’in cold and now it doesn’t work maybe you have some water in the system, a line may be frozen (never heard of this though). On the passenger side of the tranny there are the two coolant lines. The top port is the coolant return bottom is the tranny output.

Can you test a 2003 GMC Sierra 1500?

The 2003 GMC Sierra 1500 has not been tested. Like what you see? Find the best deal on a GMC Sierra 1500 today. There are for sale near you. Certified child passenger safety technicians conduct hands-on tests of a car’s Latch system and check the vehicle’s ability to accommodate different types of car seats.

What kind of oil does a 2003 GMC Sierra use?

GMC Sierra 2500 HD / 3500 6.6L 2003, SAE 10W-30 Synthetic Blend Heavy Duty Diesel Motor Oil, 1 Gallon by Lucas Oil®. This product is made of high-quality components to meet and exceed strict quality requirements. Designed using… GMC Sierra 2500 HD / 3500 6.6L 2003, SAE 15W-40 Heavy Duty Diesel Motor Oil, 1 Gallon by Lucas Oil®.

What kind of engine does a GMC Sierra 1500 have?

Key Specs. of the 2003 GMC Sierra 1500. Base trim shown. Body Type: Truck See similar vehicles. Engine: 300-hp, 6.0-liter V-8 (regular gas) Drivetrain: 4×2. Towing Capacity: 10,200 lbs.

What to do if your car has no oil pressure?

Once the engine has warmed up the oil pressure returns to what could be considered “normal”. After the cold start, no oil pressure problem, the engine and the oil pressure is fine for the rest of the day. Let it even set overnight though and I have a repeat no oil pressure with start up.

What kind of engine do you need to tow a Sierra?

Sierra’s 9,200-lb rating requires a properly equipped AT4 Crew Cab Short Bed 4WD model with 5.3L V8 engine. Before you buy a vehicle or use it for trailering, carefully review the trailering section of the Owner’s Manual. The weight of passengers, cargo and options or accessories may reduce the amount you can tow.

Is the 5.3 litre Chevy engine what you need?

August 13, 2020 by Tom Harbid The Chevy 5.3 L V8 engine, also known as the Vortec 5.3 or the EcoTec3 is generally looked at as a reliable and trustworthy engine. The Vortec 5300 is a small block V8 that was produced in 1999 for the first time.

What should fuel pressure be on Silverado truck?

Does it stay down near 52, drop further, or does it come back up to 58? If you jumper the fuel pump test lead (labeled “fuel pump prime connector” in Chilton’s wiring diagram and is a red wire coming out of the power distribution box that just dead ends.

What kind of fuel pump does a Sierra 1500 have?

Use the fitment form at the top of the page to select your exact year and engine type for your GMC Sierra 1500. GM Genuine Parts Fuel Pump Module Assemblies are designed, engineered, and tested to rigorous standards, and are backed by General Motors.

Truck is a 2003 Silverado with approx. 110,000 on it. Yep. First thing to look at. Do check your oil, of course, but I’m sure that’s fine. Light came on due to a red area reading.

What should the oil pressure be at idle?

Manual says the pressure should be 40 psi at idol, but the gauge is inaccurate. You can test it by T-tapping a pressure gauge in line with your oil pressure sending unit, and see if you are actually running the correct pressures. Question 1, how often do you change your oil?

What’s the oil pressure on a 2003 Silverado?

I have a 2003 Silverado with the 5.3. Has been babied and taken care of with regular oil changes of 10W30 and Lucas additive. When you start the truck up, it runs maybe 60 psi and drops to around 40 psi at warm idle.

Navigation