What does the p0400 Mercedes Benz code mean?

EGR flow malfunction could be caused by a clogged EGR valve or EGR tube. Before replacing any parts try cleaning the EGR valve, tube and passages. The cost to diagnose the P0400 MERCEDES-BENZ code is 1.0 hour of labor.

What is the OBD 2 fault code p1404?

OBD II fault code P1404 is a manufacturer specific code that is defined by General Motors (Chevrolet in particular) as “Exhaust Gas Recirculation (EGR) Closed Position Performance”, and is set when the actual position of the EGR valve pintle does no coincide with the position of the EGR valve pintle the PCM (Powertrain Control Module)…

What does a code p0400 on an EGR mean?

A code P0400 may mean that one or more of the following has happened: Plugged EGR passage which restricts the flow of exhaust gasses Faulty EGR solenoid wiring/harness

What causes the VCM to set the p1404 DTC?

SEVERE OCCURRENCES MAY CAUSE THE VEHICLE CONTROL MODULE (VCM) TO SET A P1404 DTC BECAUSE THE VCM PERCEIVES THAT THE EGR VALVE IS STUCK OPEN. 1. USING THE TECH 2 SCAN TOOL, EXERCISE THE EGR VALVE, AND VERIFY THE [EGR] VALVE’S ACTUAL AND DESIRED POSITION TRACK.

What does a p1400 Ford engine code mean?

Check for damaged components and look for broken, bent, pushed out, or corroded connector’s pins. What does this mean? The cost to diagnose the P1400 FORD code is 1.0 hour of labor. The auto repair’s diagnosis time and labor rates vary by location, vehicle’s make and model, and even your engine type.

How does the p1400 Mitsubishi manifold differential work?

This is done by redirecting small amounts of exhaust gas back through the upper intake to get mixed in with the air/fuel charge. The resultant diluted air/fuel mixture (i.e., less oxygen per cubic foot) burns cooler and combustion chamber temperatures are reduced accordingly, thereby lowering NOx emissions.

What causes a Mercedes Benz EGR flow malfunction?

EGR flow malfunction could be caused by a clogged EGR valve or EGR tube. Before replacing any parts try cleaning the EGR valve, tube and passages. What does this mean? Cost of diagnosing the P0400 MERCEDES-BENZ code Labor: 1.0 The cost of diagnosing the P0400 MERCEDES-BENZ code is 1.0 hour of labor.

How much does it cost to diagnose a p0400 code?

The cost to diagnose the P0400 code is 1.0 hour of labor. The auto repair’s diagnosis time and labor rates vary by location, vehicle’s make and model, and even your engine type. Most auto repair shops charge between $75 and $150 per hour. How much do you know about cars? When is the code detected?

What does the code p0400 on the EGR mean?

Code P0400 is triggered when the EGR temperature sensor does not see a temperature change when the EGR is commanded to open. These sensors tend to get a lot of carbon buildup that causes them to lose sensitivity to the heat from the EGR gases.

What are the diagnostic codes for Mercedes Benz?

Mercedes-Benz Diagnostic Trouble Codes (DTC) for 1996+ models Powertrain P0100 Mass or Volume Air Flow Circuit Malfunction P0101 Mass or Volume Air Flow Circuit Range/Performance Problem P0102 Mass or Volume Air Flow Circuit Low Input P0103 Mass or Volume Air Flow Circuit High Input P0104 Mass or Volume Air Flow Circuit Intermittent

What is the option code for Mercedes W140?

Please note that the meaning of some codes changed over the time: E.g. code 212 which was Hinterachse Uebersetzung 1:3,92 / rear axle ratio 1:3.92 with W113 (230SL/250SL/280SL Pagode) and nowadays is ETS Elektronisches Traktionssystem / electronic traction support with S -Class W140 .

What does the Code 42 / 2 power steering mean?

Codes in the form of e.g. 42/2 power steering W114/115 denote the older code system. The system was changed to the newer one (e.g. code 422 power steering W114/115) whilst W114/115 series was in production.

When is the p0400 Mercedes-Benz code detected?

Labor: 1.0 The cost of diagnosing the P0400 MERCEDES-BENZ code is 1.0 hour of labor. The auto repair labor rates vary by location, your vehicle’s make and model, and even your engine type. Most auto repairs shops charge between $75 and $150 per hour. When is the P0400 MERCEDES-BENZ code detected?

What does the Mercedes Fault code p0801 mean?

Mercedes Fault Code Fault Code Meaning; P0801: Reverse Inhibit Control Circuit Malfunction: P0803: 1-4 Upshift (Skip Shift) Solenoid Control Circuit Malfunction: P0804: 1-4 Upshift (Skip Shift) Lamp Control Circuit Malfunction: P0805: Clutch Position Sensor Circuit Malfunction: P0806: Clutch Position Sensor Circuit Range/Performance: P0807

What are all the codes on a Mercedes Benz?

Use an advanced OBD-II code reader to read and erase Engine CEL, Transmission, ETS, ABS, Airbag and other systems. There are also codes for other control units such as transmission, ABS, SRS, ESP, 4ETS, airbag, A/C. Mercedes-Benz can have up to 47 control units. You can NOT diagnose them with a simple OBD-2 scanner.

How to get a quote for a p0400?

Get a quote and book an appointment online or speak to a service advisor at 1-800-701-6230. No more waiting rooms! Our mechanics will come to you to diagnose and fix the P0400 code. How can we help? Our service team is available 7 days a week, Monday – Friday from 6 AM to 5 PM PST, Saturday – Sunday 7 AM – 4 PM PST.

What does p0110 mean on a check engine light?

P0110 is a diagnostic trouble code (DTC) for “Intake Air Temperature Sensor Circuit Malfunction”. This can happen for multiple reasons and a mechanic needs to diagnose the specific cause for this code to be triggered in your situation. Our certified mobile mechanics can come to your home or office to perform the Check Engine Light diagnostic.

What does the p0100 Mercedes-Benz MAF sensor mean?

P0100 MERCEDES-BENZ Meaning The Mass Air Flow (MAF) sensor is placed in the stream of intake air. It measures the intake flow rate by measuring a part of the entire intake flow. It consists of a hot film that is supplied with electric current from the Engine Control Module (ECM).

What does p0110 stand for in Mercedes-Benz intake air?

P0110 MERCEDES-BENZ Meaning The Intake Air Temperature (IAT) sensor is built into mass air flow sensor or in some vehicles mounted to the air filter duct housing. The sensor detects intake air temperature and transmits a signal to the Engine Control Module (ECM).

What does the p0115 code on the dash mean?

This is because the P0115 code is referring to the ECT SENSOR, and the dash gauge is operated by, usually a one-wire SENDER. Basically a different sensor that the code doesn’t refer to.)

What happens to the p0115 coolant temperature sensor?

As the temperature of the coolant changes, the resistance changes on the ground signal to the PCM. When the engine is cold, the resistance is high. When the engine is warm, the resistance is low. If the PCM detects a voltage condition that seems abnormally low or high, P0115 will set. An example of an Engine Coolant Temperature ECT sensor

What does p0120 mean on the TPS sensor?

P0120 Meaning. The throttle position sensor (TPS) responds to the accelerator pedal movement. This sensor is a kind of potentiometer which transforms the throttle position into output voltage, and emits the voltage signal to the Engine Control Module (ECM).

What causes a p0120 code on a throttle return?

Potential causes of the P0120 code include: Sticking throttle return spring MAP or TPS connector corrosion Misrouted harness causing chafing Bad TPS Bad PCM

What are the p0120 and p2135 codes?

I have 2 codes P0120 and P2135, I first replace the pigtail and TPS sensor same problem and codes (Reduced engine power). so i bit the bullet and replaced the throttle body along with another new TPS (it came attached ) still same problem…any help?… codes P0340 and P0120 please help!

How much does it cost to diagnose a Mercedes Benz code?

The cost of diagnosing the P0400 MERCEDES-BENZ code is 1.0 hour of labor. The auto repair labor rates vary widely across the country, and even within the same city. Most auto repairs shops charge between $75 and $150 per hour. When is the P0400 MERCEDES-BENZ code detected?

What causes a p0120 TPS a circuit malfunction?

Potential causes of the P0120 code include: Sticking throttle return spring MAP or TPS connector corrosion Misrouted harness causing chafing If you have access to a scan tool, with KOEO (Key on engine off) observe the TPS voltage.

What was the cause of the p0400 system malfunction?

P0400 – Exhaust gas recirculation (EGR) system -flow malfunction Trouble Code Fault Location Probable Cause P0400 Exhaust gas recirculation (EGR) system – Hose leak/blockage, basic setting not ca

How long does it take to diagnose a p0400 code?

Before replacing any parts try cleaning the EGR valve, tube and passages. The cost to diagnose the P0400 code is 1.0 hour of labor. The auto repair’s diagnosis time and labor rates vary by location, vehicle’s make and model, and even your engine type.

A code P0400 may mean that one or more of the following has happened: Plugged EGR passage which restricts the flow of exhaust gasses Faulty EGR solenoid wiring/harness

What is the p0400 code on a 2005 Ford Focus?

2005 ford focus has po106 po400 po452 po191 po300 codes seems to run fine you can clear out codes po452 instantly comes back any help or ideas would be appreciate… help ,get p0400 code on nissan frontier with 2.4 Lt. has only 40000 miles on it. my best guess is egrc solenoid. am i on the right track? would appreciate any help…

Where can I find the Mercedes Fault code?

Any of the scanners listed above can read and clear the Check Engine / Service Engine Fault Codes. The codes above are retrieved by plugging a diagnostic scanner into the OBD-II port located under the dash, and scanning for fault codes. Location of OBD II port used to retrieve Mercedes-Benz fault codes.

What causes a Mercedes P2004 code to break?

Mercedes P2004 Cause. Weak material used in construction of the intake manifold air lever is the main common cause of Mercedes P2004 codes. If you have a broken manifold air lever you may want to consider replacing your old lever with a high strength aluminum design.

What kind of engine does a Mercedes P2004 have?

Affected Models: C230 2006-2007 C280 2006-2012 C350 CLK350 E350 ML350/450 R350,SLK280/300/350,Engine M272 M273

What does the fault code on a Mercedes mean?

Mercedes Fault Code: P261F71 1 Check Engine Light 2 Little to no acceleration 3 Coolant leak 4 Brake Pedal Pressure 5 Engine overheating More …

What does p0400 stand for in engine control module?

All our repairs are backed by our 12-month / 12,000-mile warranty. P0400 is an OBD-II generic code that the engine control module (ECM) detected the engine exhaust gas recirculation (EGR) valve is not flowing recirculated exhaust gases when it is commanded to open the flow of gases into the intake manifold.

Mercedes Fault Code: P261F71 1 Check Engine Light 2 Little to no acceleration 3 Coolant leak 4 Brake Pedal Pressure 5 Engine overheating More

What are the symptoms of an OBD-2 trouble code?

If the PCM detects that the amount of exhaust gases entering the cylinder were insufficient or non-existent, this code is set. No symptoms will likely be noticed by the driver other than the MIL (malfunction indicator lamp). However, non visible symptoms will be increased combustion temperature and increased Nox emissions.

Navigation