What does P1778 Nissan step motor function mean?

P1778 NISSAN Meaning The step motor’s 4 aspects of ON/OFF change according to the signal from the Transmission Control Module (TCM). As a result, the flow of line pressure to the primary pulley is changed and the pulley ratio is controlled. This diagnosis item detects when the electrical system is OK, but the mechanical system is NG.

What are the malfunctions of DTC p1773?

P1773 malfunctions of DTC P1773 and C2104. 2010 outlander. Just trying to narrow… I have a customer who has a 2011 Mitsubishi Outlander Sport. Good afternoon. I have a customer who has a 2011 Mitsubishi Outlander Sport. As he was driving down the road, the service transmission … read more Certificate Of Completion, A…

What are the error codes for CVT transmission?

Codes: P1778, P0746 and P0868: Hi All, My Car Has a CVT XTRONIC My car has a CVT XTRONIC transmission. A quick summary of my question: my car is diagnosed with these error codes;P0746, P1778 and P0868. Do I need to replace the transmission? Or a transmission specialist would be able to fix the issues?

What does 178 mean on a CVT transmission?

Find a transmission shop that works on them as a lot of guys are not in tune with them yet. Manufacturers are slow to teach outside mechanics about them. The two codes are listed in picture for causes, but 178 is the step motor which means it works okay electrically, but mechanically there is something wrong.

Is the Trans fluid pressure low on a P1778?

Because I do have a P1778 code. But I also have a P0868 which is “trans fluid pressure low”. I have the V6 model, not sure if that matters? BTW, I live in the counry about 30 miles from the Twin Cities, and I sometimes have to go there. The drivers on the road near and in the cities are much more aggressive drivers than us country folks.

What causes a transmission fluid temperature sensor to set to p0868?

Some common causes of code P0868 could include the following- Damaged, burnt, shorted, disconnected, or corroded wiring and/or connectors In some cases, a defective transmission fluid temperature sensor might contribute to the setting of code P0868, although this is rare

What to do when your Nissan P1778 Got you Down?

7)take a piece of dental floss about a foot long and hold the spring loaded arm back against the stepper motor and return the valve body back to the transmission. 8)after you have a few bolts in place remove the floss before you tighten all the way.

What should I replace CVT fluid in Nissan P1778?

10)rejoin the fluid pan to the transmission and replace with quality cvt fluid. Amsoil makes a great product. I hope this helps and if you have questions please feel free to ask. Well done, you’ve shown that with the right amount of elbow grease, you can salvage what might otherwise have sent you looking for another car.

What does 178 mean on a Nissan Leaf?

The two codes are listed in picture for causes, but 178 is the step motor which means it works okay electrically, but mechanically there is something wrong. It is kind of hard to believe that Nissan would charge more than what you paid for the car unless the person selling it knew of a problem and dumped.

What are the possible causes of P1778 code?

P1778 Possible Causes 1 Faulty Step Motor 2 Step Motor harness is open or shorted 3 Step Motor circuit poor electrical connection

What does p0880 mean on a transmission controller?

Each time the engine is started, the PCM performs a self-test of all controllers. If no acceptable TCM power input signal (battery voltage) is discovered, a code P0880 will be stored and a malfunction indicator lamp may be illuminated, In some models, the transmission controller will also enter limp-in mode if a code of this type is stored.

What does the OBD II fault code p0868 mean?

What Does Code P0868 Mean? OBD II fault code P0868 is a generic code that is defined as “Transmission fluid pressure (TFP) sensor –low”, and is set when the PCM (Powertrain Control Module) detects that the transmission fluid pressure is lower than the minimum allowable value.

What is the p0868 transmission fluid pressure sensor?

P0868 – Transmission fluid pressure (TFP) sensor -low Trouble Code Fault Location Probable Cause P0868 Transmission fluid pressure (TFP) sensor Wiring, short to earth, TFP sensor, ECM/

P1778 Possible Causes 1 Faulty Step Motor 2 Step Motor harness is open or shorted 3 Step Motor circuit poor electrical connection

What is the fault code on a Nissan?

The car is a 2011 with 140,000 miles. It went into super granny limp mode and would not accelerate over 5 mph. I checked for fault codes and P1778 came up. I erased the fault and it drove fine… accelerated better than ever and the fault didn’t return.

How much does it cost to repair a Nissan P1778?

The cost of diagnosing the P1778 NISSAN code is 1.0 hour of labor. The auto repair labor rates vary by location, your vehicle’s make and model, and even your engine type. Most auto repairs shops charge between $75 and $150 per hour.

What does the error code p1776 mean?

Error Code P1776 is defined as Transmission Control Switch Circuit is Out of Self-Test Range. It is set when the KOER (Key On Engine Running) self-test Transmission Control Switch (TCS) is not cycled. This error code is a manufacturer-specific trouble code, meaning it does not apply to all vehicles makes.

The cost of diagnosing the P1778 NISSAN code is 1.0 hour of labor. The auto repair labor rates vary widely across the country, and even within the same city. Most auto repairs shops charge between $75 and $150 per hour.

What’s the death code for a Nissan Altima?

P1778 got you down? About 6 months ago I received the death code P1778 (stepper motor) in my 2008 Altima.

How to repair Nissan step engine code P1778?

How is the P1778 NISSAN code repair? Start by checking the “Possible Causes” listed above. Visually inspect the related wiring harness and connectors. Check for damaged components and look for broken, bent, pushed out, or corroded connector’s pins.

P1778 got you down? About 6 months ago I received the death code P1778 (stepper motor) in my 2008 Altima.

What should I do if I keep throwing P1778?

Though having been there before your stepper motor may be on the way out. Start with flush, then trans cooler. If your still throwing p1778 then change stepper motor. The fluid may just be low and worn…

When does a Nissan step motor function is ng?

As a result, the flow of line pressure to the primary pulley is changed and the pulley ratio is controlled. This diagnosis item detects when the electrical system is OK, but the mechanical system is NG. This diagnosis item detects when the state of the changing the speed mechanism in the unit does not operate normally.

What does the code P1778 mean on a Nissan Murano?

Thank Eduardo. Hello P1778 is the code for an issue with the stepper motor function. The CVT transmission on this vehicle uses a 4 position stepper motor to propel the vehicle. If the stepper motor goes bad, or has an issue it will set off the check engine light to notify the driver of the issue.

What is the Hello code on a Nissan Murano?

Hello P1778 is the code for an issue with the stepper motor function. The CVT transmission on this vehicle uses a 4 position stepper motor to propel the vehicle.

How to check Nissan step motor function code?

Check the “Possible Causes” listed above. Visually inspect the related wiring harness and connectors. Check for damaged components and look for broken, bent, pushed out, or corroded connector’s pins. The cost of diagnosing the P1778 NISSAN code is 1.0 hour of labor.

Navigation