What are the fault codes for MaxxForce 15?
International MaxxForce 15 (All Years) Fault Codes CODE DESCRIPTION SPN 27 FMI 0 EGRP fault: over temperature SPN 27 FMI 3 EGRP signal Out of Range HIGH SPN 27 FMI 4 EGRP signal Out of Range LOW SPN 27 FMI 7 EGRP does not agree with commanded posit
What are the codes for 2013 International ProStar MaxxForce 13?
I have 2013 international prostar maxxforce 13. And show does codes SPN 3719, FMI 0 SPN. 1378, FMI. 31 SPN. 3055, FMI. 0 And lose … read more Vocational, Technical or Tra… Vocational, Technical or Tra…
What kind of oil is SPN 100 FMI 18?
I’m getting code spn 100 fmi 18 engine oil below warning pressure and spn 100 fmi 1 engine oil system below critical pressure. the pressure drops … read more Disclaimer: Information in questions, answers, and other posts on this site (“Posts”) comes from individual users, not JustAnswer; JustAnswer is not responsible for Posts.
What is the code for MaxxForce DT fuel delivery?
The code was DTC N/A SPN 94 FMI 1 Fuel Delivery Below Critical. We just had one of these. Try to clamp off the return from the fuel filter canister (Grey/silver line).
What are the DTC codes for Ford Focus?
P0122 – Throttle Position (TP) Circuit Low Input The TP sensor circuit is monitored by the PCM for a low TP rotation angle (or voltage) input through the comprehensive component monitor (CCM). If during key ON engine OFF or key ON engine running the TP rotation angle (or voltage) changes below a minimum calibrated limit, the test fails.
What’s the maximum DTC for a p0118 focus?
P0118 – Engine Coolant Temperature (ECT) Circuit High Input Indicates the sensor signal is greater than Self-Test maximum. The ECT sensor maximum is 4.6 volts or -50°C (-58°F). Note on some vehicles that are not equipped with an ECT sensor, CHT can be used and can set this DTC.
When did the International MaxxForce 15 come out?
First announced in 2009, it was put into production and placed into trucks by August 2011. However, this engine was very short lived due to its ability to not meet engine requirements that it was announced in September 2012 that it would be discontinued.
What is idle shutdown code on MaxxForce DT?
Idle shutdown is normal. 597-2 Brake switch circuit fault. 95% of all Internationals have this code. Ignore it. 3660-5 Injector #2 close coil open circuit.
What are the DPF codes for MaxxForce DT?
Idle shutdown is normal. 597-2 Brake switch circuit fault. 95% of all Internationals have this code. Ignore it. 3660-5 Injector #2 close coil open circuit. Usually an injector problem. Some service scanners report these codes erroneously. 3719-15 soot load lowest warning level, level 1 DPF needs regen.
Why does SPN 157 / FMI 16 appear after fuel filter repair?
Did SPN 157/FMI 16 appear after the fuel system was repaired or fuel filter maintenance was performed? Yes; the code may be set due to air in the fuel system. Clear codes and road test to verify complaint. If code does not set, release the vehicle. If code sets, Go to step 2. No; Go to step 2. Turn the ignition ON (key ON, engine OFF).
Is the 2013 Maxforce having a low boost?
I have a 2013 Maxforce having low boost. I checked the actuator and it works so then I plugged the Actuator to see if that make any difference. I am having about 7 psi more boost after plugging it and it pulls good on hills too and also as soon as the turbo kicks in I hear screeching sound.
What does low pressure mean on a MaxxForce?
Those codes are not engine, but body controller stuff. Upper is high pressure, lower is low pressure. The sound could be a failed turbo or just a leak. Those codes are not engine, but body controller stuff. Upper is high pressure, lower is low pressure. The sound could be a failed turbo or just a leak.
How to connect breakout box to MaxxForce?
Connect 180-Pin Breakout Box with ECM E1 and E2 harness to ECM E1 and E2 engine harness connectors, and leave ECM disconnected. Connect Breakout Harness ZTSE6016 to EGR engine harness, and leave EGR valve disconnected. Use DMM to measure resistance.
What do you need to know about MaxxForce Pro Star 2012?
Sensor or connector terminals: damaged or pinched wires; corroded terminals; loose, bent, or broken pins; or broken connector housing. Using Electronic Service Tool (EST) with ServiceMaxx™ software, load the 2010 Actuator session. Select EGR Position from the Actuator drop-down menu on the right side.
What does FMI stand for in failure mode?
•“FMI” is the Failure Mode Indicator. This number represents the type of failure detected. Refer to Failure Mode Indicators (FMI) below for more information. 2 BODY CONTROLLER DIAGNOSTIC TROUBLE CODES (S08327) FAILURE MODE INDICATORS (FMI) DEFINITIONS
What are the conditions to start a MaxxForce DT?
This may point to problems not seen previously and log a new active code. Conditions to start include: good battery voltage at the ecm and starter, engine rpm a minimum of 130 rpm although I like to see 150, engine oil pressure, oil supply to the high pressure oil pump, ICP during cranking above 650 although spec is higher.
Where is the oil pressure regulator on a MaxxForce 9?
If you engine is a MaxxForce 9, the oil pressure regulator is on top of the oil filter housing. What codes do you have? What codes do you have? I wish I could give you that info but I have yet to dig into what I’ll need puter wise for these things.
Why does my MaxxForce DT have low ICP?
SPN 164- Low ICP during crank is your starting issue. Could be one of the following . – Bad IPR valve , Bad HP oil pump, Dirt in the HP oil Pump inlet screen, HP oil leak under the valve cover ( pucks or injectors)or oil quality . International dealers now have a new HPOP system test procedure that uses thee CPA analyzing software.
What happens if SPN 132 FMI 11 MAF sensor fails?
If SPN 132 FMI 11 – MAF sensor calibration failed – Insufficient number of data points sets, engine conditions are not stable to accept MAF calibration 1. Check to ensure entry conditions were all met (if EOT or ECT become lower than 176 F, test will fail) 2.
What is SPN FMI for mass air flow sensor?
DIAGNOSTIC TROUBLE CODES SPN FMI DESCRIPTION 132 11 MAF sensor calibration failed – Insufficient number of data points 132 13 Mass Air Flow sensor out of calibration 132 14 MAF sensor calibration failed TROUBLESHOOTING Instructions on how to record a ServiceMaxx recording for a casefile: 1.
What are symptoms of SPN 164 FMI 1?
SPN 164 FMI 1 (DTC 2335) ICP Unable to Build During Engine Cranking SPN 164 FMI 17 (DTC 3374)ICP Unable to build during test SPN 164 FMI 18 ICP below desired level SPN 164 FMI 13 ICP adaptation in-range fault SPN 8492 FMI 1 (DTC 3334)ICP Below desired SPN 1443 FMI 2 (DTC 2242) ICP adaptation in-range fault Observations or Concerns:
FMI” is the Failure Mode Indicator. This number represents the type of failure detected. Refer to Failure Mode Indicators (FMI) below for more information. Active” or “Previously Active” will be displayed to identify whether a fault is currently active or if the fault was previously active.
What does SPN stand for on a body controller?
DEFINITIONS •“SPN” represents the Suspect Parameter Number. This number identifies the item for which diagnostics are being reported. •“FMI” is the Failure Mode Indicator. This number represents the type of failure detected. Refer to Failure Mode Indicators (FMI) below for more information. 2 BODY CONTROLLER DIAGNOSTIC TROUBLE CODES (S08327)
What is the IHC Maxforce 10 code for 2013?
2013 IHC MAXFORCE 10 CODE SPN 5541 FMI 4 KEEPS POPPING UP. Vocational, Technical or Tra… I have an International tractor with a Maxx force 13 engine. I have an International tractor with a Maxx force 13 engine. My truck lost power and I have 3 codes.Spn 5542 fmi 15 tcp1top above desired Spn 5541 fmi … read more Vocational, Technical or Tra…
What is the IHC Maxforce 7 fuel actuator code?
2016 IHC MAXXFORCE 7 was billowing black smoke replaced cracked dpf, much better now but light black smoke on acceleration puffs. Has recurring permanent codes. SPN 1244 FMI 5 FUEL ACTUATOR #2 SHORTED … read more
What is the Maxforce 13 code for 2013?
Hi i have 2013 maxxforce 13 with codes tc1top 5541/3 and 5542/15 . Computer shows desired pressure at 0 when idling with actual pressure 35+ psi … read more
Is the 2013 International ProStar MaxxForce 13 engine lost power?
2013 international prostar maxxforce 13… 2013 international prostar maxxforce 13 engine with loss of power and cant pass 58-60 mph after 10 minutes of initial start Andy I have 2 chats open with you right now. Which one you want to keep I just sent you last 8 of the vin in the other window
Why are DPF and Doc removed from ProStar MaxxForce 13?
If you have the wrong micron rating of fuel filter , it causes higher fuel inlet restriction , therefore , lower fuel pressures . Dpf and doc were removed 5 months ago and were cleaned and baked.
What does SPN stand for on a diagnostic code?
Previously active diagnostic trouble codes can only be cleared by a service tool, such as Diamond Logic® Builder (DLB). Some previously active codes may not be cleared by this method. “SPN” represents the Suspect Parameter Number. This number identif es the item for which diagnostics are being reported. FMI” is the Failure Mode Indicator.
What is the diagnostic trouble code for FMI?
Diagnostic Trouble Code Index 12 APPENDIX B: DIAGNOSTIC TROUBLE CODE INDEX465 Diagnostic Trouble Code Index DTC SPN FMI Circuit CONDITION DESCRIPTION
What should the oil pressure be on a MaxxForce 13?
Not really sure why someone would take the filter out and leave it out. Minimum safe oil pressure is 10 psi. 15 psi is fine. It is a bit lower than what is “typical”. Most are around the 20 psi mark. Minimum safe oil pressure is 10 psi. 15 psi is fine.
Why is my MaxxForce engine not working properly?
If playback doesn’t begin shortly, try restarting your device. Welcome to my channel “The Transporter”. I will take you for a ride and show you how a trucking business is made and operated.
Where to find SPN code for 16 engine?
SPN codes description SPN Code SPN Name SPN Description 16 Engine Fuel Filter Differential Pressure (see also SPN 1382) Differential pressure measured across the fuel filter located between the fuel tank and the supply pump. See SPN 1382 and Figures SPN16_A & SPN16_B.
Which is the service manual for MaxxForce 7?
Procedures, specifications, Maintenance Manual and parts defined in published technical service EGES-345-1 International® MaxxForce® 7 literature may be altered.
What was the cost of the Navistar MaxxForce engines?
That was on top of the $700 million development cost of the engines. The MaxxForce engines tarnished the manufacturer’s reputation. Sales plunged. Navistar lost almost half its market share as costs soared and losses climbed. Navistar said it expects the settlement will “accelerate our efforts” to move past the MaxxForce debacle.