What are the F1-11 and e2-11 codes?

What are the F1-11 and e2-11 codes?

2012 Honda CR-V was involved in a collision. Driver side (steering) airbag was deployed. Scanned the vehicle and got these codes; F1-11, E2-11. … read more 2012 Honda CR-V was involved in a collision and only the steering wheel airbag was deployed as a result. When scanned, these codes were … read more Bought an 06 civic at auction. I am.

When to set F1-11 DTC e4-11?

– DTC E4-11 is set if the system triggered a passenger’s side airbag deployment but the airbag was prevented from deploying by the ODS. Replace the right side impact sensor (first).

Do you need to replace the seat belt tensioner on an F1-11?

So,for the F1-11 you need to replace the driver side seat belt tensioner since the airbag did not deploy. For the E2-11, you will need to replace the passenger side airbag even though it did not deploy because it was triggered, but not deployed due to no one in the passenger side seat.

Why is my Trane air conditioner error code E19?

Explanation: Error of electronic expansion valve open in the outdoor unit (when it is detected more than once) Explanation: Error of electronic expansion valve close in the outdoor unit (when it is detected more than once) *PLEASE SEND ME ANY COMMENT, SUGGESTION OR CORRECTION YOU MAY HAVE. I occure E19 error what happen ?

2012 Honda CR-V was involved in a collision. Driver side (steering) airbag was deployed. Scanned the vehicle and got these codes; F1-11, E2-11. … read more 2012 Honda CR-V was involved in a collision and only the steering wheel airbag was deployed as a result. When scanned, these codes were … read more Bought an 06 civic at auction. I am.

What to do if you get an f3-e code on your oven?

Select the ‘cancel’ function and wait 60 seconds. If error code reappears then replace the touch pad, or touch pad and control board (clock) if all one assembly. All F3-E Codes – Oven Temperature Sensor (RTD) or Warming Drawer Defect – Replace oven temperature sensor (RTD).

What is the 4 digit failure code for Whirlpool?

4 Digit Failure Codes(for 2 digit codes see below) F1 – E0 EEPROM communication error 1. Disconnect power for at least 30 seconds. 2. Re-apply power and observe for at least one minute. 3. If code re-appears, replace control board (also called ERC or clock). Note: Applies to all F1-E… codes except F1-E3.

– DTC E4-11 is set if the system triggered a passenger’s side airbag deployment but the airbag was prevented from deploying by the ODS. Replace the right side impact sensor (first).

What do the warning lights on my Honda mean?

Luckily for you, we are on hand to let you know what each warning light means. Whether it’s a dashboard warning light for your Honda’s engine/emissions, driver assistance, brakes, fuel levels, or something as simple as what lights are being used, it’s important to know your Honda.

How to get a radio code for a Honda Civic 2008?

Start the car. Turn off the radio. Hold #1 and #6 buttons for a while. You should see an eight digit code, in some cases you’ll get other codes too but copy the eight digit or be real cool and all of them as they appear together so you know you get it right.

Where is the service check light code on a Honda?

1. Connect SCS service connector special tool No. 07PAZ-0010100, or equivalent, to service check connector located under the passenger’s side of dash. 2. Turn the ignition on. 3. MIL will indicate DTC’s by outputting a number of flashes.

What is the fault code for a Honda Accord?

P1297 Electric Load Detector (ELD) Circuit Low Voltage P1298 Electric Load Detector (ELD) Circuit High Voltage P1300 Random Misfire P1324 Knock Sensor Power Source Circuit Low Voltage P1336 Engine Speed (RPM) Fluctuation Sensor Intermittent Interruption P1337 Engine Speed (RPM) Fluctuation Sensor No Signal