How to troubleshoot a Jeep XJ Cherokee problem?
“If the power lock system is inoperative with either front door power lock switch, test the Passenger Door Module (PDM)…If the power lock system is inoperative with only the driver side front door power lock switch, test the Driver Door Module (DDM).” I can help you troubleshoot beyond these symptoms, too.
When do you know your Jeep Cherokee ignition switch is bad?
If your Jeep Cherokee is starting right up, but then immediately dies, that is a very good indication that the ignition switch is bad. Here’s what happens. You aren’t getting power to the ignition or fuel pump while the key “rests” in the run position.
Why is the instrument cluster on my Jeep Cherokee not working?
Checked the fuses, as well as the hot to the cluster from the fuse and back to the battery. Next plan is the grounds and then the connectors. Not liking this instrument panel
How can I Fix my Jeep XJ Cherokee door?
Possible remedy: There is a slot on the rear facing edge of the door that has an adjustable slide for the door button. Work the button and watch this lever move. You can loosen the Torx screw and move the lever/button adjuster to allow for a full throw of the outside handle button when you press the button.
“If the power lock system is inoperative with either front door power lock switch, test the Passenger Door Module (PDM)…If the power lock system is inoperative with only the driver side front door power lock switch, test the Driver Door Module (DDM).” I can help you troubleshoot beyond these symptoms, too.
Why are there no parking lights on my 92 Cherokee?
92 cherokee limited No Parking Lamps,Dash,lights! Well this started after the battery went dead. First the head lamp flashed after installing new battery. reset security with key lock and unlock drivers and passenger door. Head lamps stopped flashing after locking and unlocking passenger door.
Checked the fuses, as well as the hot to the cluster from the fuse and back to the battery. Next plan is the grounds and then the connectors. Not liking this instrument panel
Why does my Jeep Cherokee stall while driving?
A significant number of drivers have reported that not only did their Jeep Cherokees lose engine power while driving, but in nearly all cases, stalling occurred without any warning and with no indicator lights on the instrument panel.
What are the features of a 1999 XJ Cherokee?
The XJ Cherokee in the article is our 1999 Cherokee Sport 4-door with power windows, power door locks, power mirrors and remote keyless entry (RKE). The passenger side front door module is the “brains”, containing both relays and switches. A quote from Chrysler helps:
Where is the right front switch on a Jeep Cherokee?
With the relays and switching that take place within the PDM (right passenger front switch module), it’s best to replace this right front door module/switch assembly— in any case .
What kind of transmission does a Jeep XJ have?
In 1988, a much needed improvement replaced the BA10/5 ; the AX15. This more durable transmission was the five-speed offered with the XJ through 1999. The 1984-1986 XJ series had two choices of transfer cases. XJ’s with Command Trac, Jeep’s part-time four-wheel-drive option, used the NP207.
When did Jeep XJ change to 4.0 engine?
With the change to the 4.0 engine, the engine bay of the Stage II Jeep XJ was changed in 1987, including small changes to the firewall, inner fenders and most significantly the front clip.
How many miles does a Jeep Cherokee take to stall?
Jeep Cherokee XJ’s and Cherokee KJ’s with less than 25,000 miles have experienced stalling problems, but most cases seem to involve vehicles with 75,000 miles or more on them, and it is with particular reference to these older vehicles that the PCM is most relevant.
Can a jeep be converted to a GM engine?
Jeep XJ Cherokee / Wagoneer & MJ Comanche One of the most fascinating powertrain conversion platforms among the Jeeps are those into the Jeep XJ Cherokee. The conversion results can be fantastic. With improvements in power, fuel economy, reliability and broad range driveability, there is nothing like an XJ with a GM V8.
How do you change the wiper motor on a Jeep Wrangler?
You have to unbolt the struts from the windshield frame and lay the frame out on the hood to switch the wiper motor. Getting the plug undone is the tricky part. The part that is on the motor side will fit through the opening in the top of the dash, but the part on the Jeep harness side doesn’t.
What are the switches on a Jeep Cherokee?
Instrument Cluster, Radio, Rear Wiper/Washer Switch, A/C Heater Control or Heater Control, Rear Window Defogger Switch, Extended Idle Switch, Front Fog Lamp Switch, Rear Fog Lamp Switch, Transmission Range Indicator Illumination (PRNDL), Transfer Case Switch Illumination
How can I get my windshield wipers to work?
My squirters work just fine, its just the windshield wipers. The wiper motor is fairly cheap, I have seen them on Ebay for around $35. You have to unbolt the struts from the windshield frame and lay the frame out on the hood to switch the wiper motor.
Is there a two door version of the Jeep Cherokee?
Both two- and four-door versions of the XJ Cherokee were offered throughout its lifetime, each having exactly the same track and wheelbase measurements. Two-door models, however, received longer doors and front seats that could fold forward to assist in rear passenger entry and exit.
When did the Jeep Cherokee get a new engine?
A stiffer unibody frame brought improvements to noise, vibration, and harshness (NVH) measurements. Also contributing to NVH improvements were new door seals that reduced wind noise at higher speeds. In the middle of the 1999 model year, vehicles with the 4.0 L engine received a revised intake manifold.
Why does my RKE not work on my XJ Cherokee?
The RKE also does not work (and have changed to fresh batteries). If the fix is just as you mentioned in your tutorial (i.e. changing the PDM or DDM) that would be great. Also, cheers for all the helpful tutorials you do mate, you’re a real champ!
Both two- and four-door versions of the XJ Cherokee were offered throughout its lifetime, each having exactly the same track and wheelbase measurements. Two-door models, however, received longer doors and front seats that could fold forward to assist in rear passenger entry and exit.
A stiffer unibody frame brought improvements to noise, vibration, and harshness (NVH) measurements. Also contributing to NVH improvements were new door seals that reduced wind noise at higher speeds. In the middle of the 1999 model year, vehicles with the 4.0 L engine received a revised intake manifold.
When did the Jeep Cherokee Wagoneer come out?
A variation on the Cherokee from 1983 to 1990 was the Jeep Wagoneer. These were unrelated to the similarly named full-sized Grand Wagoneer models that had carried the Wagoneer name before this point.
The XJ Cherokee in the article is our 1999 Cherokee Sport 4-door with power windows, power door locks, power mirrors and remote keyless entry (RKE). The passenger side front door module is the “brains”, containing both relays and switches. A quote from Chrysler helps:
Possible remedy: There is a slot on the rear facing edge of the door that has an adjustable slide for the door button. Work the button and watch this lever move. You can loosen the Torx screw and move the lever/button adjuster to allow for a full throw of the outside handle button when you press the button.
With the relays and switching that take place within the PDM (right passenger front switch module), it’s best to replace this right front door module/switch assembly— in any case .
Is the Jeep Cherokee XJ a good car?
According to FourWheeler, the earlier Jeep Cherokee XJ models are not the golden years. Models before 1987 had early model transfer-case options that didn’t hold up as well.
What kind of transmission does a Jeep Cherokee XJ have?
From 1987 and on, the Jeep Cherokee XJ primarily had four-speed automatic transmissions. However, in 200, the NV35000 five-speed manual transmission appeared. It’s pretty rare and may be expensive if you can find one.
Why is the alternator on my Jeep not charging?
Looks like the field coil of the alternator isn’t getting power. There are 3 wires attached to the alternator. One is a big fat wire that goes to the battery, this is the alternator output. The other two wires feed power to the field coil.
What to do if your Jeep remote is not working?
1. Remove the battery. 2) Use 1/3 of a sticky note, fold it, and place it within the round battery slot (on the floor beneath where the battery is placed. 3) Put the battery in on the folded note. WALAAA! Thank you so much, this worked for me!!! It simply is a problem with the battery positioning within the fab. 1. Remove the battery.
A significant number of drivers have reported that not only did their Jeep Cherokees lose engine power while driving, but in nearly all cases, stalling occurred without any warning and with no indicator lights on the instrument panel.
What does the PCM do on a Jeep Cherokee?
The PCM (Powertrain Control Module) is a computerized system that monitors and controls various systems on a Jeep Cherokee, including vital operations such as engine timing, the transmission (gear shifting), anti-lock braking, fuel to air ratio mixing and quite a few others.
Why does my Jeep not start when there is no power?
There is a wire that goes to the power distribution box on the finder close to the battery, if you don’t have power to it nothing will work. Could be a dirty connection there or there is also a large main fuse in the PDB that supplies power to all circuits in the jeep. I would check the fuse box for problems.
Where does the power supply go on a Jeep Cherokee?
There is a wire that goes to the power distribution box on the finder close to the battery, if you don’t have power to it nothing will work. Could be a dirty connection there or there is also a large main fuse in the PDB that supplies power to all circuits in the jeep.
What kind of Jeep Wrangler wont turn over?
Enter your ride HERE to be a part of MAY’s Ride of the Month Challenge! I have a 92 wrangler 4.0 6cyl with 5 speed, 200,000 miles on it and it just died. I have no electrical, wont turn over, no lights.
Why does my Jeep 4.0L have no spark?
It’s almost impossible for all 6 COP ignition coils to fail at the exact same time… so the most likely cause for this no spark condition is a bad crankshaft position sensor. But before you go out and replace the crank sensor, you need to test it (to make sure it’s fried).
Where are the fuses in a Jeep Wrangler YJ?
Fuses and relay Jeep Wrangler 1986-1995 For the Jeep Wrangler (YJ) 1986, 1987, 1988, 1989, 1990, 1991, 1992, 1993, 1994, 1995 model year. Fuse box in passenger compartment. fuse box diagram. legend. 1 – 15 Amp (Lt. Blue) – Turn Signals, Back-Up Lights. 2 – 20 Amp (Yellow) – Courtesy Light, Cargo Light, Radio (1991).
Why are the gauges on my Jeep YJ not working?
It is not that uncommon for Jeep Wrangler YJ dash gauges to go out and the fix can be fairly easy…. if you can find the problem. I show the steps I went through on how to fix the gauges on my 1994 Jeep wrangler YJ. 2: Cleaning the ground wires on the engine. 3: Removing the instrument cluster to check the connection of the gauges.
Why does my Jeep wander off the road?
by Tim Petruccio. Wandering can be caused by a single problematic source in your Jeep’s steering, suspension, tires, or brakes. Some vehicles can wander so bad that it actually causes a pulling sensation to the left or right when you have your hands on the steering wheel.
Why does my Jeep WJ have death wobble?
Over time, the tie rod end on the upper portion of the Panhard or Track Bar develops “play” in it due to wear and miles on the vehicle (some applications like the Grand Cherokee WJ, Ford truck, and the Dodge Ram have a rubber bushing configuration instead, which also wears out).
Is there a problem with my 2000 Jeep Grand Cherokee?
No one has added a helpful site for this 2000 Grand Cherokee problem yet. Be the first! Read reviews of repair shops in your area. Enter your zip code: Search CarComplaints.com for these popular complaint phrases…
Why does my Jeep Grand Cherokee shut off while driving?
My 2000 Jeep Grand Cherokee shuts off while driving. The first few times It shut off I was able to restart it with in a few minutes. I changed the crank sensor and that worked for a couple of weeks. It then did it again. I had to wait 20 minutes for it to start back up again. About 30 minutes later it did it again..
Why does my Jeep Cherokee keep stalling?
While certainly frustrating, these stalls can also have serious consequences. Here is why your Jeep Cherokee keeps stalling: Many stalling problems can be attributed to the PCM or crankshaft sensor and there are steps you can take to fix these issues yourself or at the very least point your mechanic in the right direction
Why do I need to disable Auto start on my Jeep?
Auto Start-Stop is ‘designed’ to save us some gas money, it might save us a few dollars per year, but that’s actually not the goal of the manufacturer. This guide will show you how to disable this annoying feature on Jeep Cherokee, Grand Cherokee and Wrangler & Compass.
Are there any problems with the Jeep Cherokee?
Our ’99 had issues with the power window/door lock system, the A/C dash panel air flow and the “No Bus” gauge drop-off problem. Each of these problems is common to the XJ Cherokees and TJ Wranglers, making forums all over the internet. On our Cherokee, I worked through the troubleshooting and solutions for each.
How to fix Jeep Cherokee driver power windows?
ALSO: If your windows are “slowing down” or “working “Sometimes”” it is mostly going to be the motor and regulator IN THAT troublesome door. This fix is for when all of the windows are functioning properly BUT ONLY from the driver pannel. PS. This IS reversable and to be clear, the “ALL WINDOW LOCK-OUT” is basically being by-passed.
Are there any problems with the Jeep Wrangler?
Exasperated owners may say “it’s a Jeep thing,” but the truth is, every car or truck you can think of has its own unique quirks and issues, and Jeeps are no exception. Jeeps like the Cherokee, Grand Cherokee, and Wrangler are known to run into certain problems time and again. Of course, I don’t want to discourage anyone from driving a Jeep.
What causes a fault code on a Jeep Grand Cherokee?
Transmission plug adapter is located under the car and often starts leaking oil. Once oily, the plugs have bad electrical connection and transmission goes into limp mode and starts showing fault codes. It is easy to check the plug – look under the car and check if the plug is oily.
How to know if your Jeep has a problem?
Inspect the HVAC black plastic case in the passenger side footwell for evidence of leak. Coolant will run down the case and under the carpet. Leak is usually slow/minor. 2. Problem:*Engine cranks but will not start. May have died while driving. Related symptoms: Fuel gauge shows ’empty’, however the fuel tank is not empty.
What’s the problem with the heater on my Jeep?
Related symptom: Odd smell from A/C dash vents. Passenger side carpet may be wet/moist. Cause:*The heater core is leaking. Fix:*Replace the heater core. Alternative/temporary repair: Locate the 2 heater hoses going to the firewall underhood.