How to reset the PassLock system on a 2000 Silverado?
If the Passlock system identifies the key as unauthorized, the engine stalls. Leave the ignition switch in the “Run” position as the “Security” light blinks on and off for approximately 10 minutes. Turn the ignition switch clockwise to start the engine immediately after the “Security” light stops flashing.
How can I disable the alarm system on a 1997 Jeep Grand?
If there is the Honda added security box installed at the lower left side of the kick panel turn the ignition key to the on position. Locate the small button on the box and hold it down for 90 seconds and the alarm will bypass. Call to the dealer, this was their response: With the ignition key try to start the vehicle.
What to do if your security system breaks on a GM car?
On older GM cars two small wires will break near the tumbler which will activate the system. In this case the tumbler must be repaired or replaced. Call to the dealer, this is their response: Hold the panic button on the key fob for 2 seconds. Close all of the doors and while using the key lock and use the key to unlock the lock the driver’s door.
How to reset Ford Lincoln Mercury immobilizer system?
Ford Lincoln Mercury Reset of the Immobilizer System Call to the dealer, this is their response: Hold the panic button on the key fob for 2 seconds. Close all of the doors and while using the key lock and use the key to unlock the lock the driver’s door. If that doesn’t work remove the negative battery cable for 15 seconds and reconnect.
Why does my GMC Truck alarm keep going off?
My truck alarm recently started going off randomly. I tried removing the battery from both of my key fobs, but it still occurred. My first Google results seemed to say that the battery could have a low charge, but they weren’t specifying a GMC brand vehicle.
What should I do if my GM security light is flashing?
Insert ignition key and turn to the “ON” position. Do not attempt to start the engine. Leave the key in the “ON” position for approximately 11 minutes. The security light will be steady on or flashing for the 11-minute period. Do not proceed to Step 2 until the security light turns off or stops flashing. 2.
How to reset the computer on a GMC Truck?
Click to expand… Click to expand… Click to expand… Click to expand… Click to expand… This system consists of: the Powertrain Control Module (ECM or PCM), Body Control Module (BCM) or Passkey theft deterrent module, and the ignition lock and key. In most cases, the theft deterrent duties are handled by a Passkey module.
How to reset PassLock reset system on Chevy?
1. Turn the key to ON and attempt to start the engine and release the key to the ON position. 2. The SECURITY light will illuminate. Wait 10 minutes until it turns off. 3. Turn the key to OFF for 10 seconds. 4. Turn the key to ON and attempt to start the engine.
How long does it take to reset PassLock 3?
Passlock III reset procedure, reset security system on chevy, buick, oldsmobile, cadillac, pontiac, saturn, hummer. Passkey III Reset procedure. Make sure the battery if fully charged because this procedure may take up to 30 minutes and you cannot start the vehicle during this time.
How do I reset the PassLock on my car?
1. Insert the master key with the black head into the ignition lock cylinder 2. Turn the key to ON but do not start the engine. The SECURITY light will turn on and stay on. 3. Wait 10 minutes or until the SECURITY light to turn off. 4. Turn the key to OFF for 5 seconds. 5. Turn the key to ON but do not start the engine.
How long does it take to erase a PassLock key?
If you’re adding a new key to the system, you MUST have all the older keys with you. All previously learned keys will be erased from the system as soon as you program the first key. After the first key has been relearned, immediately insert the next key to be programmed within 10 seconds.
How long does it take to reset PassLock on a Chevy?
Reset security system on chevy, buick, oldsmobile, cadillac, pontiac, saturn, hummer. Make sure the battery if fully charged because this procedure may take up to 30 minutes and you cannot start the vehicle during this time. The instrument panel cluster (IPC).
Passlock III reset procedure, reset security system on chevy, buick, oldsmobile, cadillac, pontiac, saturn, hummer. Passkey III Reset procedure. Make sure the battery if fully charged because this procedure may take up to 30 minutes and you cannot start the vehicle during this time.
How do I Turn Off the PassLock security light?
1. Turn the key to ON and attempt to start the engine and release the key to the ON position. 2. The SECURITY light will illuminate. Wait 10 minutes until it turns off. 3. Turn the key to OFF for 10 seconds. 4. Turn the key to ON and attempt to start the engine. If it starts and run, the system has reset.
If you’re adding a new key to the system, you MUST have all the older keys with you. All previously learned keys will be erased from the system as soon as you program the first key. After the first key has been relearned, immediately insert the next key to be programmed within 10 seconds.
If the Passlock system identifies the key as unauthorized, the engine stalls. Leave the ignition switch in the “Run” position as the “Security” light blinks on and off for approximately 10 minutes. Turn the ignition switch clockwise to start the engine immediately after the “Security” light stops flashing.
How to reset an automotive security system [ video ]?
Disconnect the battery using the negative cable wait one minute and reconnect. Call to the dealer, the service writer got us one of their technicians to help us and this was his response: unlock the vehicle with the key fob twice to recognize the key is valid. Push the panic button twice to disable the alarm. Roll the windows up and lock the car.
How can I Reset my Volkswagen security system?
Volkswagen Security System Reset. To deactivate the anti-theft system use the unlock button on the remote key. Unlock the driver’s door using the key and then switch the ignition switch to the on position. If that doesn’t work exit the vehicle and roll up all windows, then use the key to lock the driver’s door.