How to replace the camshaft position sensor on a Hyundai Santa Fe?

How to replace the camshaft position sensor on a Hyundai Santa Fe?

Camshaft position sensor packed in the other day and there were no video’s on here to show how to replace it ( perhaps because of how easy it was ), So here goes. Fault: Car kept cutting out and failing to start, ignition would turn over but nothing else. Fault Code on the diagnostics machine P0340. Part Number 39300-27000.

Can a bad crankshaft sensor cause the engine to stall?

If the crankshaft position sensor or its wiring have any issues, it can cause the crankshaft signal to be cut off while the engine is running, which can cause the engine to stall. This is usually a symptom of a wiring problem, however a bad crankshaft position sensor can also produce this symptom.

Can a bad crankshaft sensor cause a check engine light?

Another issue of a potential problem with the crankshaft position sensor is an illuminated Check Engine Light. If the computer detects a problem with the crankshaft position sensor’s signal, it will activate the Check Engine Light to alert the driver of the problem. A Check Engine Light can also be set off by a wide variety of other issues.

How does the crankshaft position sensor work in a car?

It monitors the position and rotational speed of the crankshaft and sends the information to the engine control unit so it can make appropriate adjustments based on operating conditions.

What are the electrical problems in a Hyundai Santa Fe?

The piston seals in the abs modules’s hydraulic valve could leak brake fluid into the electronic control unit (euc) . An electrical short in the abs module could increase the risk of an engine compartment fire.

When did the Hyundai Santa Fe come out?

Hyundai Santa Fe – mid-size crossover, created on the platform Hyundai Sonata. The car was named after the city in New Mexico. In 2001, this model was the first crossover Hyundai, released at the same time as the Ford Escape / Mazda Tribute and Pontiac Aztek.

When did the Hyundai Santa Fe blind monitoring system come out?

Beginning in 2014, the blind blind monitoring system is included in the basic kit. In 2017 the car will be equipped with a system of opening doors “hands-free”. In 2016, the model was upgraded, changing the appearance (bumpers, grille, headlights, etc.) and equipment.

Where is the camshaft position sensor on a Honda Accord?

elynbert, the camshaft position sensor monitors the position of the camshaft. It is mounted at the right hand side (looking from the front of the engine)of the cylinder head. You should make out the plug with the wire and see that the sensor is being mounted with 1 10mm bolt. 1. Disconnect negative battery cable. 2.

Why is my camshaft not working on my Hyundai Accent?

Error code P0012 is not confined to a bad camshaft sensor. This code indicates that there is a timing problem which needs to be checked. The camshaft sensors and coil packs were replaced on a Hyundai Accent with 65,000 miles, however, the engine will not start?

How do you remove a camshaft position sensor?

You should make out the plug with the wire and see that the sensor is being mounted with 1 10mm bolt. 1. Disconnect negative battery cable. 2. Disconnect wire connector from sensor. 3. Remove sensor mounting bolts. 4. Remove the sensor from the rear of cylinder head. 1. Install camshaft position sensor in rear of cylinder head. 2.

Camshaft position sensor packed in the other day and there were no video’s on here to show how to replace it ( perhaps because of how easy it was ), So here goes. Fault: Car kept cutting out and failing to start, ignition would turn over but nothing else. Fault Code on the diagnostics machine P0340. Part Number 39300-27000.

Why is my camshaft position sensor not working?

Since it says circuit, that means the problem could lie in any part of the circuit – the sensor itself, the wiring, or the PCM. Don’t just replace the CPS (camshaft position sensor) and think that will definitely fix it.

How much is a camshaft sensor from Advance Auto Parts?

Advance Auto Parts has 19 different Camshaft Position Sensor for your vehicle, ready for shipping or in-store pick up. The best part is, our Hyundai Santa Fe Camshaft Position Sensor products start from as little as $46.32. When it comes to your Hyundai Santa Fe, you want parts and products from only trusted brands.