How to replace lower ball joint on Chevy Silverado?

This video outlines the complete process of removal and replacement of the upper control arm and lower ball joint on a 2008 Chevrolet Silverado 2500 HD 4X4 with torsion bar front suspension. The process is similar on many GM trucks and includes tips and tricks to help make the job easy and do it right. The entire process was unedited for time.

How much does a GMC Sierra front replacement cost?

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM. received a Ball Joint Front Replacement. GMC Sierra 1500 Ball Joint Replacement (Front) costs $270 on average. What is the Ball Joint Front all about?

Where are the ball joints on a Chevy Equinox?

Depending on the suspension design, ball joints can be found either in the front or the rear. The vehicle may need to be taken to a shop for wheel alignment after this service. Mobile mechanics do not have the machinery to align wheels.

When to replace the ball joint in the front of a Dodge Grand Caravan?

Check the entire suspension system for any problems. When applicable, make sure the ball joints are lubricated during a major service. What common symptoms indicate you may need to replace the Ball Joint Front? Clunking noise from front tires. Steering wheel shakes. Car moves to the right or left, especially going over the bumps.

How to replace a lower control arm ball joint?

Replacing a Lower Control Arm Ball Joint. Learn how to replace a lower ball joint by pressing it out of the control arm and pressing the new one back in. To watch the longer, in depth version, click the link below. Press out a Ball Joint (In-depth):

What do you do with a loose ball joint?

Ball joints equipped with a taper are typically used on tie rods and the connection between the control arm and steering knuckle. Once that taper on a ball joint breaks loose, it’s free so there is no struggle such as what you may find with a slide in cylinder shaped object.

How to tell if a ball joint is bad?

Learn how to diagnose a bad ball joint for both an upper and lower control arm. I also quickly show you how to tell if it is a bad tie rod, bushings, or a bad bearing just in case your ball joint is not bad. A bad ball joint will make noise which is the first symptom of knowing it’s bad.

How do you replace a ball joint on a truck?

Trucks and some cars – separate the steering knuckle from the ball joints with a ball joint fork and set aside. This process usually requires a lot of force and a BIG hammer! Carefully inspect and remove any snap rings that may be securing the ball joint in place. Using a ball joint press, press the old joint out of the control arm.

Can a ball joint be removed from a steering knuckle?

In most cases, a ball joint press and ball joint fork will be needed to remove the ball joint and separate the control arm from the steering knuckle, which both of these are available for free through AutoZone’s Loan-A-Tool program. For ball joints that are bolted on, simply unbolting the bolts will separate the joint from the control arm.

How to replace the ball joints to a 99 Ford Explorer?

3) Remove lower ball-joint castle nut and upper ball joint retaining bolt 5) Retract the axle out of the steering knuckle and suspend it using a bungee cord out of the way. 8) Pound the lower ball joint back out with a hammer or use a press tool. 9) Remove upper control arm and replace (It houses the upper joint).

Can a ball joint be removed from a control arm?

For ball joints that are bolted on, simply unbolting the bolts will separate the joint from the control arm. Some ball joints have factory hot-rivets to secure them to the Control Arm.

How do you put a new ball joint in a car?

Slide the new rubber boot over the ball joint’s stud and guide the new ball joint back up through the steering knuckle hole, where it came from. Bolt the joint into place using the hardware included.

How do you replace ball joint on McPherson strut?

Leave the castellated nut in place, just a few turns in to keep it in a safe place. If you’re working on a McPherson strut suspension remove the “pinch bolt” that clamps the ball joint stud. Pop loose the ball joint.

How do you know if ball joints need to be replaced?

Inspect the ball joints to make sure they need to be replaced. Figure out if your vehicle’s got a strut-style suspension or a control arm, then check the ball joint by either jacking up the control arm near the ball joint to check for wheel play, or by jacking up the car and using a pry-bar to check for wheel play in a strut-style suspension.

How do you put a new ball joint in a car?

What happens when you replace a ball joint in your car?

Bleed the brakes, if necessary. It’s a good opportunity to do any other repairs you might need to do with the brakes, since you’ve got them off. Replacing a ball joint can affect alignment. If a ball joint is worn enough, and the vehicle was previously aligned, it might be wise have the vehicle realigned.

How to replace a steering knuckle hole in a soccer ball?

Guide the new joint through the knuckle hole. Slide the new rubber boot over the ball joint’s stud and guide the new ball joint back up through the steering knuckle hole, where it came from. 2 Bolt the joint into place using the hardware included.

How to repair control arm and ball joint assembly?

A control arm and ball joint assembly from O’Reilly Auto Parts reduces repair time. If you need a new control arm and ball joint assembly, visit O’Reilly Auto Parts for your complete repair. When autocomplete results are available use up and down arrows to review and enter to select. Touch device users, explore by touch or with swipe gestures.

How are control arms used in a car?

Control arms allow wheels to move up and down while preventing forward and rearward movement. Other vehicles include control arms with built-in ball joints that must be replaced as a unit if they begin to fail. If any of these parts fail, they may compromise handling, comfort, and may result in serious separation…

Do you need to replace the ball joint in a control arm?

If it fits tight then you will need to remove the ball joint from control arm and see if a new ball joint will fit tight in the control arm or control arm still will need to be replaced. This is why you were advised to replace the whole control arm. Was this answer helpful? Thank you for your feedback! Sorry about that.

Can a CV axle be replaced with a ball joint?

To replace or perform repairs on or near the ball joint such as replacing a control arm or a CV axle the ball joint will need to be undone which means taking the nut off of the joint and applying pressure while striking the spindle or control arm bulk head with a hammer.

How do you remove a ball joint from a car?

The most difficult part of removing any ball joint is disconnecting the taper fit stud at the end of the joint. Some ball joints are made into the lower or upper control arm while in other applications the joint can be unbolted separately. It is strongly suggested to have the car aligned after replacing a ball joint. What Goes Wrong?

How do you replace the ball joint on a Cavalier?

The original ball joint in the Cavalier was retained to the control arm by three rivets which will require drilling to remove the ball joint. However, if the ball joint has been replaced before, simply remove the three nuts and bolts, and remove the ball joint from the control arm.

How to replace upper control arm ball joint?

Upper Ball Joint Replacement. This video will show you how to replace the Upper Control Arm Ball Joint on a Chevy Trailblazer, GMC Envoy, etc. Replacing a ball joint is fast and easy and can be done with basic hand tools and a ball joint press you can rent for free at your local parts store.

How do you install a new control arm?

Remove the ball joint from the control arm. Install the new ball joint with the three nuts and bolts provided with the new ball joint. Tighten the nuts and bolts using a ratchet and socket on the nut, and a hand wrench to hold the bolt head still.

Navigation