How to replace left front axle seal and CV axle?
If playback doesn’t begin shortly, try restarting your device. Exploring the science and engineering behind automobile design and repair. Videos you watch may be added to the TV’s watch history and influence TV recommendations.
How do you replace a water pump on an Audi A3?
A new gasket, rubber seal, or RTV sealant, as required, is installed and then the new pump. The bolts are torqued in sequence using a calibrated inch pound torque wrench. For applications where the water pump is driven by the timing belt, the timing belt must be removed.
How do you replace a water pump in a car?
Remove the new water pump from the box and match it to the old pump. Check the mounting flange for the fan clutch and the gasket surface they should match identically. Also, a new gasket or O ring will be included with the new water pump. This will help seal the pump to the block or timing cover and avoid leaks.
When to replace the CV axle on a 4Runner?
Discussion in ‘ 4th Gen 4Runners (2003-2009) ‘ started by wnelax04sr5, Sep 5, 2016 . An issue that arises often from lifting, offroading, or just general wear and tear, is that of a bad or going bad CV axle. some telltale signs can be clunking, binding during turns, or vibrations felt through the steering wheel and chassis.
If playback doesn’t begin shortly, try restarting your device. Exploring the science and engineering behind automobile design and repair. Videos you watch may be added to the TV’s watch history and influence TV recommendations.
What’s the best way to change an axle?
By this time, you can put the wheel back on the vehicle (again, the same as you would when changing a tire). After the wheel is on, you can lower the car off the jack and jack stands. Tighten the axle nut. Finally, you can retighten the axle nut once the vehicle is back on the ground.
What to do if front drive axle comes loose?
Check beforehand because using a pry bar until one of these came loose probably would be a bad idea. Warning: Some vehicles will spill transmission fluid as soon as the inner axle stub clears the seal. Be ready with a drain pan.
How to replace the Left Front CV axle on a 2000 rodeo?
Remove the tire and wheel. Remove the drain bolt to drain differential oil. During the work, be sure that the differential case is supported by the jack. Remove the brake caliper fixing bolt and hang the caliper. Remove the antilock brake system speed sensor. (If equipped with antilock brake system) Remove the locking hub.
By this time, you can put the wheel back on the vehicle (again, the same as you would when changing a tire). After the wheel is on, you can lower the car off the jack and jack stands. Tighten the axle nut. Finally, you can retighten the axle nut once the vehicle is back on the ground.
How does a CV axle work on a front wheel drive car?
A typical inner CV joint has three rollers on a tripod (spider) that can slide inside the CV joint housing, so the CV axle can extend or contract as needed. Typical CV axle (shaft) of a front wheel drive car with a Rzeppa outer CV joint and closed tripod-style inner joint. The inner CV joint can work under small angle too.
Check beforehand because using a pry bar until one of these came loose probably would be a bad idea. Warning: Some vehicles will spill transmission fluid as soon as the inner axle stub clears the seal. Be ready with a drain pan.
Can a front wheel drive axle be replaced?
Balls and grooves will show wear before the joint fails completely. Replacing a front-wheel-drive axle is straightforward, although physically demanding. Get the replacement axle before you start, as well as a new spindle nut and a cotter pin or two.
When do you need an axle seal replacement?
Let’s start with the first question. The axle seal replacement is not a part of regular maintenance, the seal only needs to be changed if it leaks. How do you know if an axle seal is leaking? Gear oil or transmission fluid drops on your driveway are some of the early signs.
Which is the right side of the axle to replace?
And it’s usually the right side that goes first because here in the lefthand-drive US of A, we turn sharper around righthand corners than lefthand ones. Sometimes the rubber boots covering the joints fail from age or are torn by road debris, letting the grease out and dirt and water in.