How to replace GM PassLock ignition key lock cylinder?

Press the small release tab (see pictures) While turning key to the ON Position Installation is the reverse of the above procedures, see below for the relearn procedure Clear all Diagnostic Trouble Codes (DTC). Record and/or repair your DTCs before clearing. You can clear the codes by disconnecting the battery for 10 minutes.

How to test a new ignition lock cylinder?

Step 10: Test the operation of the new ignition lock cylinder. Before you reconnect the battery, make sure your new ignition lock cylinder moves to all four positions with the new key. Test this function three to five times to verify the repair was completed correctly.

Where is the cover on an ignition lock cylinder?

On most vehicles, there is a plastic or metal cover on the ignition lock cylinder. Remove the small screw that holds this cover on, typically located on the bottom of the switch. Once the screw has been removed, carefully slide the cover off the ignition lock cylinder. Step 6: Remove the lock cylinder.

How do you change the lock cylinder on a Buick?

Insert the key that came with the new unit into the new lock cylinder, and rotate the key in all the positions and back to the “Off” position. Plug the new lock cylinder electrical connector to the wiring harness. Place the covers on the steering column and tighten the mounting screws using the Phillips screwdriver.

How do you remove ignition key cylinder?

To remove key cylinder from ignition switch, insert key in ignition switch and remove the torx screw on the side of the cylinder. Rotate the key one click clockwise and the key cylinder will unseat from ignition switch. When key cylinder is unseated, it will be approximately 1/8 inch away from ignition switch halo light ring.

How much to change ignition lock cylinder?

The average cost for an ignition lock cylinder replacement is between $200 and $261 . Labor costs are estimated between $83 and $106 while parts are priced between $117 and $155.

Can a locksmith fix an ignition cylinder?

Yes. The beauty of choosing to have a locksmith help you with your ignition cylinder replacement is that they can offer mobile appointments as well as emergency services. Either a 24 Hour emergency locksmith or an auto locksmith will be able to assist you.

Can a locksmith get a key out of an ignition?

Also, a locksmith will be able to tell you whether or not it can be repaired or if you will have to get the ignition completely replaced . In this instance, you should keep in mind that the locksmith will most likely have to extract your car key before they begin any work since you have the key stuck in ignition.

How to relearn the pass lock sensor code?

The vehicle is now ready to relearn the Pass lock Sensor Data Code and/or password on the next ignition switch transition from OFF to CRANK. Turn OFF the ignition, and wait 5 seconds.

When do you need to relearn the ignition switch?

The Hall effect or Passlock sensor inside the lock cylinder housing goes bad intermittently and the Body Control module forgets the code or signal from the sensor and the 10 minute relearn procedure needs to be done in order to get the vehicle started. We do it all of the time at the shop for our customers.

Is there a way to reset the engine control module?

There are a few ways to reset your Engine control modules. One way is by disconnecting the battery cable for 2 to 3 minutes and waiting to see if the check engine light comes back on upon reconnecting the battery and start the car.

Do you have to relearn Pats to replace PCM?

Replacing PCM only — A or D type PATS If only the PCM is being replaced on a PATS control function type A or D vehicle, no relearn is required (please refer to the Ford PATS chart to determine PATS type). Simply put the original key in the ignition, turn to ON or RUN and wait for 20 seconds.

How to do a Relearn on a PassLock system?

To perform a relearn on a Passlock system, make sure there is a fully charged battery in the vehicle. The battery will be used for 30 minutes without the alternator available for charging. Connect a battery charger to the battery to ensure power is available while programming.

When to replace the Powertrain Control Module ( PCM )?

When replacing the Powertrain Control Module (PCM) on a PATS-equipped vehicle, a parameter reset or relearn procedure must be performed after the PCM is installed. Vehicles with PATS will not start until this on-car procedure is successfully performed.

How do you remove ignition switch from car?

Insert a straightened out paperclip into the slot just to the left of the key cylinder. This will lock the cylinder from starting. Inserting your screwdriver into the cylinder and turn it as far as you can to the right. Pull on both the paperclip and the screwdriver to gently slide the switch out of its current position.

How do you remove an ignition lock cylinder?

Step 8: Loosen the screws on top of the ignition lock assembly. The lock cylinder is secured to the lock assembly by a button on the bottom of the housing and two screws on top of the lock assembly. Loosen the two screws on top to allow you to remove the cylinder.

How do you test a new ignition key?

You may need to turn the new ignition key in the lock cylinder to the accessories position before inserting it into the ignition switch. Test your ignition switch by reconnecting the electrical connections and the negative battery terminal cable. Turn on your vehicle.

Do you need a key for ignition cylinder?

There are a variety of different ignition cylinder designs for vehicles, some of which require the original key to turn the lock cylinder to the accessories position to fix the part in the most efficient way.

What are the symptoms of a broken ignition lock?

Some of the common symptoms of a damaged or broken ignition lock cylinder include the vehicle not starting or power not supplied to the vehicle when the ignition is turned. Most modern cars that have keyless remote starting have a key that has a computer chip inside of it.

How to do a Relearn on Passkey III?

To perform a relearn on a Passkey III system, make sure there is a fully charged battery in the vehicle. The battery will be used for 30 minutes without the alternator available for charging. Connect a battery charger to the battery to ensure power is available while programming.

How long does it take to relearn the ignition switch?

When performing this relearn, all previously learned keys will be erased. Additional keys may be relearned immediately after the first key has been learned by inserting the additional key and turning the ignition switch to on within 10 seconds of removing the previously learned key. Turn key to the “ON” position without starting the engine.

When do I need to relearn the security key?

Start the If the vehicle starts and runs normally, the relearn is complete. If additional keys need to be relearned: Insert the next key to be Turn the key to the “ON” position within 10 seconds of removing the previously used key. Wait for security light to turn It should happen fairly quickly.

How to relearn the GM ignition switch procedure?

GM ignition switch 10 minute relearn procedure 1 Security Indicator Lamp operation. The Body Control Module controls the security indicator lamp in the instrument cluster by sending messages to the instrument cluster over the class 2 serial data 2 Passlock Operation. 3 GM 10 minute relearn procedure.

The vehicle is now ready to relearn the Pass lock Sensor Data Code and/or password on the next ignition switch transition from OFF to CRANK. Turn OFF the ignition, and wait 5 seconds.

What to do if you have a PassLock / ignition issue?

Here is my dilemma, I have a passlock/ignition issue. Here is what it does: 1. Get in the truck 2. Stick the key in 3. Without even turning the key, the truck tries to crank, sometimes 2-3 times 4. Take key out 5. Passlock light comes on 6. Wait 10 minutes and then crank Those steps happen about once a week.

What to do when your PassLock light goes off?

A temporary fix is to leave your key in the ignition, at the “auxiliary” position for about 10-15 minutes until the security light shuts off. When the light shuts off you can try to start the engine again. Rinse, repeat, and cry. A more permanent solution is to either replace the ignition lock cylinder or bypass the sensor.

What happens if you put the wrong PassLock on a car?

PASSLock ignition locks vary by the version (PASSLock I or II), the type of connector, and if wired, the length of the wire. Installing the incorrect ignition lock will usually result in the vehicle not being operable.

Why did General Motors start the PassLock system?

Aug 1st, 2005 The PassLock system was designed to prevent vehicle theft by disabling fuel to the engine if attempts are made to start the vehicle without the correct bitted key. PASSLock increased the level of security while retaining the ease of service and costs offered by standard ignition lock systems.

How does the PassLock sensor on a car work?

Voltage to the lock cylinder case sensor is provided by the BCM. The BCM measures the voltage on the sensor circuit. The voltage value indicates whether the Passlock sensor has been activated by the rotation of the lock cylinder or whether the lock cylinder has been removed, indicating a tamper situation.

What’s the name of the ignition lock cylinder?

The ignition lock cylinder is the cylindrical tumbler and key that is used to power on and start the vehicle. While many newer vehicles are now being manufactured with push button and keyless power and starting systems, traditional ignition lock cylinders are still commonly found on many road…

Why is my ignition lock cylinder not working?

The ignition lock cylinder is connected to an electronic ignition switch, they work power on and start the vehicle. If the ignition lock cylinder wear out or breaks, it may prevent the vehicle from starting when the key is inserted and turned. A no start condition can also be caused by a wide variety of other issues,…

Where is the electronic ignition switch located on a GM car?

A typical symptom of failure is the security light illuminating on the dash. Also, keep in mind the electronic ignition switch is located just behind the lock cylinder. It is the plastic part that the ignition lock cylinder fits into. It contains the actual electrical connections and wiring and it sends current to numerous different components.

What to do if your car key won’t turn in?

Please do not poke around inside the ignition lock cylinder. A dirty ignition can be fixed by spraying small doses of an electrical cleaner in the ignition then gently sliding the key in and out of the ignition cylinder many times. ( DO NOT use this method on Honda, Acura, Toyota or any vehicle that uses a high security key ).

How to permanently disable GM pass lock system?

•Disable Pass Lock system to prevent from being stranded in the future. This tutorial varies depending if the ignition is located: If your ignition is located in the dash then you will be removing the panels on the passenger underside (toe board) of the dash.

Navigation