How to replace AC blend door actuator on Jeep Grand Cherokee?
2011 Grand Cherokee replace ac blend door actuator on the… 2005 Jeep Grand Cherokee A/C only blowing cold on drivers side. Passenger side vents are blowing room normal air. … read more
How to replace AC blend door actuator on right side?
2011 Grand Cherokee replace ac blend door actuator on the right side how can put right position or alignment? 2011 Grand Cherokee replace ac blend door actuator on the… 2005 Jeep Grand Cherokee A/C only blowing cold on drivers side. Passenger side vents are blowing room normal air. … read more
Why is my Jeep JGC blend door not working?
What I discovered was this is a very common problem with my model of JGC (1999-2004). I love my Jeep, but the person that designed this blend door actuator system needs to find new work. The design is inherently weak, and relies on a calibration phase that puts intense pressure on the weakest points in the system.
Why does my Jeep Wrangler have a bad blend door actuator?
If you have a clicking/knocking when opening your JK door or setting the climate control to full cold it is most likely a bad blend door actuator. If you have a clicking/knocking when opening your JK door or setting the climate control to full cold it is most likely a bad blend door actuator. Skip navigation Sign in Search Loading… Close
How much does a Jeep Grand Cherokee door actuator replacement cost?
The average cost for a Jeep Grand Cherokee HVAC blend door actuator replacement is between $467 and $572. Labor costs are estimated between $405 and $511 while parts are priced at $62. This range does not include taxes and fees, and does not factor in your specific model year or unique location.
How to remove the blend door actuator on a jeep?
Remove the lower portion of the heater duct. You can now visually inspect the blend door actuator up against the center console, attached to the blend box, but the screws will seem impossible to remove! To get to those screws, you must remove the upper portion of the heater duct. It’s made as a clam shell so it comes apart in two pieces.
Is the blend door gear on my JGC overland broken?
I have a 2011 JGC Overland, and the blend door gear on the driver’s side is broken. I ordered the gear and set out to replace it myself, but I’m stumped. As you can see in the picture there is a screw that sits behind an aluminum piece of the core dash structure.
What are the symptoms of a bad blend door actuator?
The symptoms of a bad blend door actuator include a lack of heat or air conditioning, or failure of air to blow through some or all of the vents. The actuator motors may also make a noise if they’ve failed, but this isn’t always the case.
What kind of actuator does a Jeep Grand Cherokee use?
We offer a full selection of genuine Jeep Grand Cherokee Blend Door Actuators, engineered specifically to restore factory performance. Please narrow the Air Blend Door Actuator results by selecting the vehicle.
Why is my Jeep Grand Cherokee blend door not working?
I have a problem with the blend door motor on the driver side in my Jeep Grand Cherokee 2014. The heating is working on high only and I can’t adjust the temperature. The Dealer calibrated the blend doors but the problem still came back. I think the blend door motor is not regulating across the temperature range.
We offer a full selection of genuine Jeep Grand Cherokee Blend Door Actuators, engineered specifically to restore factory performance. Please narrow the Air Blend Door Actuator results by selecting the vehicle.
How to replace a blend door actuator in a jeep?
Hold the actuator in place with your hand and see if its operator correctly by using Heat and AC. STEP NINE: Replace the F@ $%ING screws. STEP TEN: Grab a beer and give yourself a pat on the back!
How does the blend door work on a Jeep Grand Cherokee?
That gear needs to rotate counter clockwise about a quarter turn to open the blend door. But you can’t rotate the gear that far without it hitting the top housing. Also that would not mesh correctly then with the bottom gear.
What do I need for blend door actuator?
You will need a 1/4 wrench and t15 torx. Cut the t15 torx bit in half with a angle grinder. JB weld it or tape it to the wrench. It will save you so much time.
That gear needs to rotate counter clockwise about a quarter turn to open the blend door. But you can’t rotate the gear that far without it hitting the top housing. Also that would not mesh correctly then with the bottom gear.
How to fix second door on Jeep Cherokee?
Install the second door, sliding the connector pin into the far side of the second door. Align and snap in the near connector. Reinstall the near actuator and test.
2011 Grand Cherokee replace ac blend door actuator on the… 2005 Jeep Grand Cherokee A/C only blowing cold on drivers side. Passenger side vents are blowing room normal air. … read more
2011 Grand Cherokee replace ac blend door actuator on the right side how can put right position or alignment? 2011 Grand Cherokee replace ac blend door actuator on the… 2005 Jeep Grand Cherokee A/C only blowing cold on drivers side. Passenger side vents are blowing room normal air. … read more
What’s the problem with the AC on a Grand Cherokee?
Grand Cherokee Ltd AC problem When running the AC heat comes out of the left side and the Right side is cold. The switching for the lower and windshield does not work only for the face. On Heat mod … read more
Grand Cherokee Ltd AC problem When running the AC heat comes out of the left side and the Right side is cold. The switching for the lower and windshield does not work only for the face. On Heat mod … read more
Where can I buy a Jeep Grand Cherokee a / C heater?
Shop AutoZone for Jeep Grand Cherokee A/C Heater Blend Door Actuator. 10% OFF $75. Use Code: DIYSAVE10 Online Ship-to-Home Orders Only