How to remove Idle Stop cap from a GM TBI?
On a factory TBI unit the idle set screw will be capped from the factory so you cannot mess with it. But you just knew one day you would. Not all caps look like the one pictured but this is the one that is hardest to remove. The easiest way is to first grind the cap flush with the surface of the throttle body.
What should the idle speed be on a GM TBI?
The exact setting is on the emissions label on the radiator shroud, but in general, the idle speed should be about 500 RPM in Drive, 700 in Park / Neutral, or if you have a manual transmission, somewhere between 600-800 RPM.
What is the TBI code on a 1990 Chevy truck?
Consult a service manual or see below for any check engine light code definitions. You can use a late 80’s or early 90’s GM TBI definition. If you have access to a scan tool use a hook up for a 1990 350 cu. in. 5.7L Chevrolet truck. For some scan tools enter VIN 10th“L” 3rd“C” 8th“K”.
Why is my TBI fuel injection light on?
Troubleshooting your TBI Fuel Injection System Most of the problems encountered while installing your fuel injection system or after a time of operation are very simple. If your check engine light is on you more than likely have a hard fault meaning something is grounded out, unplugged, operating out of range or has gone bad.
How many GMC trucks have throttle body injection?
New and Remanufactured Throttle Body Assemblies for 305, 350, 454 Chevy, GM, GMC Trucks, Cars, Vans and 6 Liter and 7 Liter Trucks. Serving our valued customers for over 30 years.
Consult a service manual or see below for any check engine light code definitions. You can use a late 80’s or early 90’s GM TBI definition. If you have access to a scan tool use a hook up for a 1990 350 cu. in. 5.7L Chevrolet truck. For some scan tools enter VIN 10th“L” 3rd“C” 8th“K”.
Troubleshooting your TBI Fuel Injection System Most of the problems encountered while installing your fuel injection system or after a time of operation are very simple. If your check engine light is on you more than likely have a hard fault meaning something is grounded out, unplugged, operating out of range or has gone bad.
Where can I drop off my GMC TBI?
Repack your core in the box that your TBI assembly came in, adhere the UPS label, and give to any UPS Driver or drop off at any UPS drop box. No paper work or long lines.
Is the idle set screw capped from the factory?
On a factory TBI unit the idle set screw will be capped from the factory so you cannot mess with it. But you just knew one day you would. Not all caps look like the one pictured but this is the one that is hardest to remove.
What should I do if my idle control motor is disconnected?
The engine should still start and run without any issue despite the idle control motor being disconnected. Be sure to tuck the wiring you disconnected up in the engine bay so it doesn’t get caught in any moving parts. Look for a difference in idle speed.
How can I tell if my idle control valve is working?
To check if an idle control valve is working properly, start by turning on your engine and letting it run for a minute or 2. Then, when it’s at an idling speed, take note of the RPMs in your car. Next, turn the engine off and disconnect the idle control motor under your hood.
What does it mean when idle control does not increase?
If the engine idle does not increase, it means there is an issue at the idle control motor of its circuit preventing the signal from changing the idle. You can purchase a bidirectional scan tool at your local auto parts store. Make sure the wiring harness is firmly connected to the idle control motor before conducting this test.
What should resistance be for idle control motor?
Connect an Ohm meter to the two and measure the resistance between them. Fords are designed to operate with the resistance in the solenoid in a range between 7.0 to 13.0 ohms. If the resistance is outside that range, the idle control motor needs to be replaced.