How to change the oil pressure on a Honda Accord?

Remove the appropriate rocker arm oil pressure switch, depending on which DTC is stored (Fig. 1). • P3400 – Replace the Bank 1 rear rocker arm oil pressure switch. • P3497 – Replace the Bank 2 front rocker arm oil pressure switch. 2. Install the new rocker arm oil pressure switch with a new O-ring. Torque each to 16 ft.-lbs. (22 Nm).

When to replace the oil pressure switch on a Honda?

Each exhibits a unique set of symptoms, but the fix is the same for both: replace it. If the vehicle’s malfunction indicator lamp (MIL) is on and diagnostic trouble codes (DTC) P3400 (VPS Stuck Off Bank 1) and/or P3497 (VPS Stuck Off Bank 2) are present, Honda recommends that one or both of the rocker arm oil pressure switches be replaced.

Where are the sensors on a Honda Accord?

Fuel Tank Pressure Sensor Air Temperature Sensor ( Ambient / Intake 1 Manifold Pressure/Vacuum Sensor Power Steering Pressure Switch Throttle Position Sensor Transmission Position Sensor/Switch Variable Valve Timing Actuator Position Sensor Variable Valve Timing Pressure Switch Camshaft Position Sensor Crankshaft Position Sensor

What does low oil pressure mean on Honda?

With correct engine oil level, a “Check Engine Oil Level” message may appear on the MID or the navigation screen. The “Low Oil Pressure” indicator on the instrument panel may also be on. After verifying the wiring and connectors are in good condition, replace the oil pressure switch.

What is the code for Honda Element oil pressure switch?

Vocational, Technical or Tra… 2003 honda element code p2646. Honda tsb suggests replacement of the v-tec oil pressure switch. replaced switch and code returned this morning. any ideas? … read more My 2005 Honda Element check engine light just came on on the way home, and it started surging when I try to accelerate.

How do you replace pressure switch on accord?

Detach the electric connector of the VTEC pressure switch and the 2 nd electrical connector attached to the VTEC solenoid spool valve assembly. 2. Using the 22mm deep socket, extension bar and ratchet, break the seal on the pressure switch, but leave it in place.

How do you reset the oil pressure switch on a Honda?

1. Turn the ignition switch to the ON (II) position. 2. Press the select/reset knob repeatedly until the engine oil life indicator is displayed. 3. Press the select/reset knob for about 10 seconds. The engine oil life and the maintenance item code (s) will blink. 4. Press the select/reset knob for another five seconds.

How much is the oil pressure switch on a Honda Accord?

Shop AutoZone for Honda Accord Oil Pressure Switch. 10% OFF $75. Use Code: DIYSAVE10 Online Ship-to-Home Orders Only

How to change the oil pressure on a car?

How to Change an Oil Pressure Switch. 1 Step 1 – Locate the Switch. The placement of the oil pressure switch will vary with car make. As a general rule, however, you’ll find the switch close 2 Step 2 – Drain the Oil. 3 Step 3 – Remove the Switch. 4 Step 4 – Replace with a New Switch. 5 Step 5 – Add New Filter and Oil.

Why does the oil pressure light go on when there is no oil?

The oil pressure switch is also known as the oil pressure sensor. It will cause the low oil pressure light to go on if it detects a lack of oil, but an oil pressure switch isn’t infallible.

What to use to replace oil pressure switch?

Materials: 22mm deep socket, ratchet with extension (30cm is more than adequate), 10mm socket or spanner, torque wrench (recommended, but won’t stop you from carrying out the repair if unavailable) 1. Detach the electric connector of the VTEC pressure switch and the 2 nd electrical connector attached to the VTEC solenoid spool valve assembly.

Is there a problem with the oil pressure switch on a Honda?

We have noticed an increase in oil pressure switch-related problems with late-model Honda vehicles recently. Two switches that seem to be consistently problematic are the rocker arm oil pressure switch and the engine oil pressure switch. Each exhibits a unique set of symptoms, but the fix is the same for both: replace it.

How do you check for oil leak in Honda?

After changing the engine oil and filter, run the engine for five minutes and then check for leaks. 1. Turn the ignition switch to the ON (II) position. 2. Press the select/reset knob repeatedly until the engine oil life indicator is displayed. 3. Press the select/reset knob for about 10 seconds.

What causes excessive oil consumption on Honda engine?

If the engine oil level is below the end of the dipstick (there is no oil on the dipstick), the low engine oil level is likely causing the DTCs. Continue with excessive oil consumption troubleshooting. 3. If the engine oil level is on the dipstick (it may be low, but there is oil on the dipstick), go to the repair procedure.

When to replace the oil pressure switch on a Honda Accord?

In most cases you replace this switch because it’s leaking oil. Not the case on this Accord. I also show how to attach an oil pressure gauge to physically measure engine oil pressure. The oil pressure sender socket in the video is part number KD2569. An equivalent socket can be picked up at most auto parts stores if needed.

Can a faulty oil pressure switch be replaced?

In this video I show you how to diagnose and replace a faulty oil pressure switch on 94-97 Accords. In most cases you replace this switch because it’s leaking oil. Not the case on this Accord. I also show how to attach an oil pressure gauge to physically measure engine oil pressure. The oil pressure sender socket in the video is part number KD2569.

Where can I get an oil pressure switch?

The oil pressure sender socket in the video is part number KD2569. An equivalent socket can be picked up at most auto parts stores if needed. http://creativecommons.org/licenses/b… Due to factors beyond the control of Bushougoma, it cannot guarantee against unauthorized modifications of this information, or improper use of this information.

Navigation