How tight should a chain be on a chainsaw?
A properly-tensioned chainsaw chain should still be just a little loose on the chainsaw guide bar, but the chain needs to be tight enough that you can’t pull the drive links out of the bar nose.
Why can’t I tighten the chain on my chainsaw?
If you can’t tighten the chain, you may not be implementing the proper tightening procedure. To adjust the chain, loosen the nuts that hold the guide bar in place. Attempting to turn the tension screw without loosening the nuts first may be the reason you can’t tighten the chain.
Why does my chainsaw keep throwing the chain?
Too much slack in your chain can cause the saw blades to jump the bar. This is commonly referred to as throwing the chain. Even if your chain saw is not throwing its chain, the tension might not be correct. Place a dime between the chain and bar, then increase the tension until the chain is snug against the dime.
Why does my chainsaw blade get dull so fast?
If your chain dulls quickly, then it could be a couple of things. Check your user’s manual to ensure that you are using the right sized file for your chain. Alternatively, you could be applying too much pressure when you file. This will create cutting edges that are too thin and dull quickly.
Where is the tension screw on a chainsaw?
the
The chain should have a slight give when you pull it, but the drive links below the sharp edges should remain in contact with the bar (the solid metal oval piece that the chain wraps around). There is a tension screw located near the base of the bar on the chainsaw.
Why does my chainsaw keep getting loose?
This one comes down to physics. When metal gets warmer, it expands. When you’re using your chainsaw, as the chain heats up, it will literally get larger. This is probably the most common reason that a chainsaw will start tight, and then get loose.
Is it OK to cut wet wood with a chainsaw?
No, it is not bad to cut the wet wood with your chainsaw. Dewdrops, raindrops, or the snow on the wood will not cause any harm to your chainsaw. It is, in fact, much easier to cut through the wet wood than dry wood because the extra moisture on the wood will act as a natural lubricant.
Why does my chainsaw chain stretch so fast?
One of the most common reasons why the chainsaw chain gets loose so fast is because of wear off caused by time and usage. New chains will need to be tightened more often because they stretch a lot during the first few uses. This is the ‘break-in’ period of your chain.
Why does my chainsaw dull so fast?
Cutting through wood that’s dirty can sometimes dull a chainsaw and there’s two factors attributed to dirt. If you’re cutting through logs and your angle of approach is too steep, a simple cut through could nick dirt or even worse, rocks on the floor causing your chainsaw to jerk, thus dulling.
What causes chainsaw chain to tighten during use?
This is caused by the chain being too tight, or being used when it is too dull. The bar will receive grooves in it which will then cause the chain to run in an awkward way. Loosen the two bolts holding the bar onto the body of the chain saw and remove the bar.
How tight should your chainsaw chain be?
The chain on even the best budget chainsaw shouldn’t be too loose to the extent of falling off the blade. It also shouldn’t be too tight such that it hugs the bade snugly without flexing. Ideally, the chain should be a bit loose on the guide bar but should be tight enough such that you cannot pull its drive links out of the bar nose.
How do I put my chainsaw chain on properly?
Secure the chain around the sprocket (a cog-type part found near the chain tension nipple) and align it along the grooves of the bar. You will see a hole for the chain-tension nipple on the end of the bar. Line these up so the nipple fits in the hole on the bar. Pull the chain to tighten it, using the screw to achieve the desired tension.
How do you change chainsaw chain?
How to Replace Your Chainsaw Chain Step 1: Remove the Old Chainsaw Chain. Step 2: Release the Chainsaw’s Tension. Step 3: Loosen the Tensioning Screw. Step 4: Threading the Chain onto the Saw. Step 5: Put the Side Plate Back On.