How does the keyless entry work on a Pontiac?
Press and hold the Unlock and Lock buttons on the keyless entry for approximately 15 seconds. When the chime sounds, the remote is programmed. The keyless remotes for Pontiac vehicles are not compatible with other vehicles and vice versa. The remote you are attempting to program must be specifically for the Pontiac vehicle.
How do you turn on a keyless remote?
Press and hold Unlock and Lock on the keyless remote for approximately 15 seconds. You will hear two chimes–one approximately every eight seconds. Release the buttons. Remove the key from the ignition. Reinsert the fuse into its slot. Insert your key and turn it to On without starting the engine.
Is there a keyless entry remote for a Pontiac Solstice?
Most Pontiac keyless entry remotes, such as the Grand Am, Grand Prix, G6 and Solstice, must be programmed by the dealer. However, some Pontiac vehicles have customer-programmable keyless remotes. Close all of your Aztek’s doors. Press and hold the “Unlock” button on your driver’s side door control panel.
When did the Pontiac Firebird come out in the US?
Designed as a pony car to compete with the Ford Mustang and Mercury Cougar, it was introduced on February 23, 1967, simultaneous with GM’s Chevrolet division platform-sharing Camaro. This also coincided with the release of the 1967 Mercury Cougar, Ford’s upscale, platform-sharing version of the Mustang.
What kind of taillights did the Pontiac Firebird have?
The Firebird’s rear “slit” taillights were inspired by the 1966–1967 Pontiac GTO. Both a two-door hardtop and a convertible were offered through the 1969 model year.
What kind of crankshaft did the Pontiac Firebird use?
The SD-455 consisted of a strengthened cylinder block that included four-bolt main bearings and added material in various locations for improved strength. Original plans called for a forged crankshaft, although actual production SD455s received nodular iron crankshafts with minor enhancements.
What was the horsepower of a 1969 Pontiac Firebird?
Power output of the other engines was increased marginally. There was an additional Ram Air IV option for the 400 cu in (6.6 L) V8 engines during 1969, complementing the Ram Air III; these generated 345 hp (350 PS; 257 kW) at 5000 rpm and 430 lb⋅ft (583 N⋅m) of torque at 3400 rpm; and 335 hp (340 PS; 250 kW) respectively.
How do you turn on a radio on a keyless entry?
Press and hold the Unlock and Lock buttons on your keyless entry for 30 seconds. When you hear a warning chime, the remote is programmed. Open the interior fuse compartment door. Examine the diagram on the back to find the fuse labeled Radio. Remove this fuse from its slot. Insert your key into the ignition.
Press and hold the Unlock and Lock buttons on the keyless entry for approximately 15 seconds. When the chime sounds, the remote is programmed. The keyless remotes for Pontiac vehicles are not compatible with other vehicles and vice versa. The remote you are attempting to program must be specifically for the Pontiac vehicle.
Most Pontiac keyless entry remotes, such as the Grand Am, Grand Prix, G6 and Solstice, must be programmed by the dealer. However, some Pontiac vehicles have customer-programmable keyless remotes. Close all of your Aztek’s doors. Press and hold the “Unlock” button on your driver’s side door control panel.
How do I relearn my GM keyless remote?
Put your key in the ignition and turn it all the way clockwise until you hear the engine come on. Make sure that the gear shift is set to park. Press and hold the Vehicle Information button until the display reads “Press V to Relearn Remote Key. ” If for some reason the display does not appear, restart your car, and repeat the previous steps.
What should I do if I Lost my GM key?
If you have lost your keys, or have just bought a new car, you will need to program a new keyless remote. There are three broad categories when it comes to GM keyless remotes: pre-2007, 2007–10 with VIC, and 2007 – 10 without VIC. If your car is a GM post-2010 model, you should contact your nearest car care professional.
How do I Turn on programming mode on my car?
Open your driver side door, and then shut it immediately. Listen for the chime to confirm that you are in programming mode. Press and hold Unlock and Lock on the keyless remote for approximately 15 seconds. You will hear two chimes–one approximately every eight seconds. Release the buttons. Remove the key from the ignition.
How to program the keyless entry on a Pontiac Grand Prix?
Enter your car, sit in the driver’s seat and close all of the doors, windows and the trunk on your car. Insert your key in the ignition on your Grand Prix and turn the key one click to the left to the “Accessory” option within the ignition options.
Can You program a new Pontiac Grand Prix remote?
If you have replaced your remote with a new one, it will not function until you have programmed it. While the dealer can program a new remote for you, it probably won’t be free. You can do it yourself and save the money in just a few minutes.
Can a 2005 Pontiac Grand Am keyless entry remote be replaced?
The keyless entry remote for your 2005 Pontiac Grand Am is programmed to the car through a specific set of commands and steps. If you have replaced your remote with a new one, it will not function until you have programmed it. While the dealer can program a new remote for you, it probably won’t be free.
Where is the fuse box on a Pontiac Grand Prix?
While the dealer can program a new remote for you, it probably won’t be free. You can do it yourself and save the money in just a few minutes. Locate the fuse box under the dash of your Grand Prix, just inside the driver’s side of the car.
How does the remote work on a car?
Insert your key into the ignition. Turn the key quickly from Off to Run three times within five seconds. Stop in Run. Listen for the doors to lock to signal that you are in programming mode. Press and hold the Unlock and Lock buttons on your keyless entry for 15 seconds. When the doors lock, then unlock, the remote is programmed.
Press and hold Unlock and Lock on the keyless remote for approximately 15 seconds. You will hear two chimes–one approximately every eight seconds. Release the buttons. Remove the key from the ignition. Reinsert the fuse into its slot. Insert your key and turn it to On without starting the engine.
How do I relearn the remote on my car?
Press the “i” button on your driver control center, until Relearn Remote Keys appears. Press the Se button on your control center–the display will change to Remote Learning Active. Press and hold the Unlock and Lock buttons on the keyless entry for approximately 15 seconds.
How can I unlock my locked GM radio?
Dial 1-800-537-5140 to connect with GM’s toll-free radio hotline. Once you’re connected, you’ll be asked to provide your vehicle’s radio identification number, along with a special dealer access code. You’ll then be rewarded with a 4-digit retrieval code, which will allow you to unlock your radio.
How do you unlock the driver’s side door?
Press and hold the “Unlock” button on your driver’s side door control panel. Continue to hold it until instructed otherwise. Insert your key into the ignition, but do not turn it. Remove the key, and then insert it again. Remove it, and then insert it a final time and leave it in the ignition. Release the Unlock button on the control panel.
How to bypass the PassLock sensor on a 2002 Pontiac Grand Am?
This web page will guide you through the steps necessary to bypass the “Passlock Sensor” on a 2002 Pontiac Grand Am, and keep the “SECURITY” light off forever. The steps necessary are similar on the other models listed above. There are generally only minor differences in how to get the radio out to get to the wires.
Dial 1-800-537-5140 to connect with GM’s toll-free radio hotline. Once you’re connected, you’ll be asked to provide your vehicle’s radio identification number, along with a special dealer access code. You’ll then be rewarded with a 4-digit retrieval code, which will allow you to unlock your radio.
Where is the ignition switch on a GM PassLock?
Pull the radio out of it’s cavity. Disconnect the wiring connector and the antenna wire, and set the radio aside. On the left side of the radio cavity, there will be an opening, through which you will be able to see the Ignition Switch.
Where do I find the PassLock code on my car?
IMPORTANT: The vehicle learns the Passlock Sensor Data Code and/or password on the next ignition switch transition from OFF to CRANK. You must turn the ignition OFF before attempting to start the vehicle. Start the engine. The vehicle has now learned the Passlock Sensor Data Code and/or password.
Press the “i” button on your driver control center, until Relearn Remote Keys appears. Press the Se button on your control center–the display will change to Remote Learning Active. Press and hold the Unlock and Lock buttons on the keyless entry for approximately 15 seconds.
Press and hold the Unlock and Lock buttons on your keyless entry for 30 seconds. When you hear a warning chime, the remote is programmed. Open the interior fuse compartment door. Examine the diagram on the back to find the fuse labeled Radio. Remove this fuse from its slot. Insert your key into the ignition.
Insert your key into the ignition. Turn the key quickly from Off to Run three times within five seconds. Stop in Run. Listen for the doors to lock to signal that you are in programming mode. Press and hold the Unlock and Lock buttons on your keyless entry for 15 seconds. When the doors lock, then unlock, the remote is programmed.
When does a Pontiac Grand Am out of gas?
(PRWEB) February 21, 2005 — If you own a 2001 Pontiac Grand Am, you’d better hope you’re not stuck somewhere bad when this hits: You go to start your car, and the engine cranks, but it seems like your out of gas, and won’t start.