How do you replace the nsbu switch on a Duramax?
Remove the 2 bolts that attach the NSBU switch (the front driveshaft will get in the way a bit but you should be able to access the bolt with the socket) and pull off the old NSBU switch. There’ll be some resistance when you pull it off.
Can you get an oil change on a Duramax?
Yes, you can do most of the maintenance yourself: oil changes, fuel filter changes, air filter, tire rotations, etc. The Duramax V8 holds 10 quarts of oil. The extra oil and the fuel filter add cost to the equation. Getting the oil change done at a dealership or a shop will run $100 at a minimum.
What kind of maintenance does a Duramax do?
Heavy duty trucks, especially turbo-diesels, are costly to maintain. Yes, you can do most of the maintenance yourself: oil changes, fuel filter changes, air filter, tire rotations, etc. The Duramax V8 holds 10 quarts of oil. The extra oil and the fuel filter add cost to the equation.
How long does it take to replace Duramax injectors?
The dealership estimates this job between 11-12 hours of labour. The injectors are underneath the engine’s valve covers. If two injectors failed, then it’s likely others will fail as well. It’s better to bite the bullet and replace all eight at once, and save of more labour costs.
How much torque does a GM Duramax have?
We’ve said it before and we’ll say it again, “The best bang-for-the buck for increasing fuel economy and torque in your 6.6L GM Duramax is a diesel tuner, or programmer.” Now the hard part….which on read more The PPE Standard Xcelerator will give you up to an additional 225HP/335 Torque.
How to lock a flywheel on a 6.6L Duramax engine?
Locks flywheel in place when removing harmonic balancer on 6.6L Duramax engines with Allison automatic transmissions Saves time by locking the flywheel at the transmission instead of having to remove the starter for water pump replacement Use 36mm 12-point socket with 3/4 square drive to remove harmonic balancer bolt and retorque on installation
What should I expect from my Chevy Duramax service?
• Steering components should be lubricated during every oil change service. • Air filter should be inspected during every service and replaced accordingly. • Brake fluid and power steering fluid should be inspected during every service and flushed accordingly.
Yes, you can do most of the maintenance yourself: oil changes, fuel filter changes, air filter, tire rotations, etc. The Duramax V8 holds 10 quarts of oil. The extra oil and the fuel filter add cost to the equation. Getting the oil change done at a dealership or a shop will run $100 at a minimum.
Remove the 2 bolts that attach the NSBU switch (the front driveshaft will get in the way a bit but you should be able to access the bolt with the socket) and pull off the old NSBU switch. There’ll be some resistance when you pull it off.
What does the GM original equipment ignition switch do?
It is a multi-position switch that activates the ignition, accessory, and cranking circuits in your vehicle. This original equipment ignition starter switch has been manufactured to fit your GM vehicle, providing the same performance, durability, and service life you expect from General Motors.
What happens when the ignition switch fails on a Chevy truck?
When this switch fails while driving the truck will stop after a few audible chimes. In addition, the gear shift lever will become stuck in the drive position and you will not be able to get it into neutral and the key will be stuck in the ignition.
What do you need to know about ACDelco ignition switches?
An ACDelco GM Original Equipment Ignition Starter Switch is a GM-recommended replacement for your vehicle’s original component. It is a multi-position switch that activates the ignition, accessory, and cranking circuits in your vehicle.
Where is the neutral switch on a car?
A neutral safety switch works just like a clutch switch except that it keeps an automatic transmission from starting in gear. The neutral safety switch will allow the engine to start with the transmission selector in park and neutral. The switch is located in two places on the vehicle.
Where is the neutral switch on a column shifter?
The switch is located in two places on the vehicle. Column shifters have the neutral safety switch located on the of the transmission. Mechanical floor shifters have the neutral safety switch located on the of the transmission.
What should I do if my neutral switch fails?
If you have the column or floor shifter in park or in neutral and the engine does not start, then the neutral safety switch may have failed. Also, if the column or floor shifter is in gear and the engine is able to start then the neutral safety switch may have failed. Step 1: Place the column shifter or floor shifter in park.