How do you replace the headlight on a Lexus IS?

Set the bolts aside and pull the headlight out just until you see the power cables. Unclip and then unplug this wire connector. The final step is to unlock the plastic headlight clip that holds the headlight to the frame. Gently lift up on the clip and the headlight should come out completely.

What kind of light bulbs do Lexus headlights use?

The only real variation in exterior lighting on the Lexus IS is in the headlights. Halogens, Bi-xenon, and even LED bulbs are available. They are not, however, interchangeable. Lexus models with halogen headlights will need two different bulbs for the high and low beams. Cars equipped with HID’s only need the one bulb. Figure 1. HB3/9005 (halogen).

Why are there so many lights on a Lexus?

There are so many lights on the Lexus IS that it can be hard to know what kind of bulb is needed when one goes out. Knowing the type of bulb and the wattage required makes fixing blown bulbs a far less stressful (and less expensive) option.

How many bulbs do you need for Lexus high beams?

Lexus models with halogen headlights will need two different bulbs for the high and low beams. Cars equipped with HID’s only need the one bulb. Figure 1.

What to do when your low beam headlight blows out?

You can often tell when a headlight blows out while you’re driving, but confirm which bulb has actually blown out by leaving your headlights on and getting out of the vehicle to check. Then get back in your vehicle and turn on your high beams. Some vehicles use a single bulb for both high and low beams while others do not.

How do you wire a sealed beam headlight?

If you are planning on wiring your sealed beam headlight, it is simple to do on your own. Here are a few quick steps and materials that you will need to get the job done with ease. Begin on turning the car off and then opening the hood. You may want to make sure that you allow the car to cool down. Sealed Beam Headlights.

How do you remove a headlight bulb from a car?

The headlight bulb should still be in a socket connected to wiring coming from your vehicle. Disconnect the wires by unclipping them from the bottom of the headlight bulb housing and pull on it gently to disconnect it.

Where are the adjustment bolts on a Lexus headlight?

Turn on your headlights and prop open the hood of your Lexus. Look for the adjustment bolts on the low beam headlight, which rests higher in the headlight assembly than the high beam. The top adjustment bolt controls the lateral direction of the beam and the lower bolt controls the vertical direction of the beam.

What causes a Lexus headlight to scatter?

A stained headlight causes light to scatter. At times moisture may build up or condense in your headlight’s interior assembly, hindering their effectiveness. This may require only removing the whole light and putting it in oven heated to 225 degrees Fahrenheit to melt the moisture.

What to use to fix foggy headlights on a Lexus?

Keep on spraying the headlight with soap as you wet sand it. Spray on three coats of Dupli Color Acrylic Enamel two, light coats and one medium wet coat after 10 minutes. Using two 2000 grit sand paper soaked overnight with soap, wet sand until the orange peel is removed.

Where are the bolts on a Lexus fog light?

There are only three 10mm bolts holding the headlight in place. Pay particular attention to the bolts. Of the three bolts, the one on the side of the lamps is a little longer than the other two. Set the bolts aside and pull the headlight out just until you see the power cables.

What to do if your Lexus headlight is stained?

Using wet sandpaper on headlight. Covered by the outer headlight glass is a projector lens that focuses light into a strong beam. If your Lexus’ lens is stained, dirt scatters light in different direction and its output is hindered by 40 percent.

What’s the best way to clean a headlight?

This may require only removing the whole light and putting it in oven heated to 225 degrees Fahrenheit to melt the moisture. Alternatively, you can wrap the headlight with three garbage bags and dip it in water heated to 100 degrees Fahrenheit for 10 to 15 minutes.

How do you replace the front bumper on a Lexus?

For the right side, turn the wheel as far to the left as possible. This gives you the access space you’ll need to disconnect the two plastic clips and four 10mm bolts that attach the lower portion of the bumper to the frame. Repeat for the left side. Figure 5. Lower bumper connectors in front wheel wells.

Can you replace the fog light on a Lexus IS?

Here’s how to replace the headlight and fog light assemblies yourself. This article applies to the Lexus IS (2005-2013). Headlights and fog lights are the most popular modification that could make a significant difference between a stock and modified Lexus.

Where is the fuse for the dome light on a Lexus?

Locate the fuse box under the driver side’s dashboard. Examine fuse #8 in the fuse box, which is responsible for the interior lights, including the dome light. If the fuse is blown, replace it with another 10A fuse. If the dome light is still dead, move on to the next step.

How do you change the flasher on a Lexus IS?

OEM flasher relay. Connect the new quick-connect clips on the new flasher relay if they fit. Otherwise, you will need to remove the clips and manually replace the wires into their correct positions to work with the new flasher. Connect the battery’s negative cable.

Is there a replacement driver side headlight assembly?

DEPO 312-1172L-AS7 Replacement Driver Side Headlight Assembly (This product is an aftermarket product. It is not created or sold by the OE car company) . Temporarily out of stock. .

What are the problems with Lexus headlight lenses?

If your Lexus original factory OEM Headlight Lens Cover Plastic Lenses Glasses have problems, like been Yellowish Scratched Lenses Crack, Cracked, Broken or have fading, faded and fogging, foggy, haze, aging etc.

Do you need to replace the headlight lens cover?

Don’t need to replace the whole headlight assembly, you only need to repair your plastic headlight lens cover, it means only need to replace the lenses cover and then your headlights can back to condition as new. 2007-2012 Lexus ES240 ES350 XV40 Headlight Lens Cover Foggy Headlamp Plastic Lenses Covers Shell Replacement

How do you replace a Phillips headlight bracket?

Pull the connector apart to unplug. There are three small Phillips head screws in the bottom of the headlamp holding the bracket. Remove these screws to get the bracket off and ready for replacement onto the new HID headlamp. Once removed, this bracket may need to be cut in order to custom fit onto the new HID headlight.

Navigation