How do you replace brake pads on a Mercedes AMG?
“Massage” the caliper’s pistons to get them back into place. Fasten the caliper hub with the large 14mm bolts. Connect the caliper slide pins in place, and give the calipers a good shake to make sure that the pads are fitted properly and not loose. Fit the wheel to the hub and torque the wheel bolts to 90 ft-lbs.
What to do when you need to replace your brake pads?
Be careful not to spray brake cleaner on rubber (brake line, caliper piston boot, dust covers, etc). Apply disk brake pad grease on the contact areas of the brake pad. This is where the caliper piston meets the back of the brake pad, and where the brake pads slides onto the metal clips that snap onto the caliper bracket.
How do you replace brake pads on a Mercedes Sprinter?
Use a G clamp or push-back tool to compress the brake piston back into the casting. I have always found it beneficial when doing this to lift the dust boot slightly and give a quick blast of WD40 or similar to assist the free movement of the piston back into the caliper. Once this is done you can proceed.
Where are the brake pads on a Mercedes C class?
This is where the caliper piston meets the back of the brake pad, and where the brake pads slides onto the metal clips that snap onto the caliper bracket. Your brakes pads may be directional and marked with an arrow. Install the arrows in the direction of wheel rotation unless the directions say otherwise. Figure 17.
How do you replace front brake pads on a Mercedes?
Removing the front brake pads is easy. Simply slide them away from the rotor and out of the caliper bracket. If your new brake pads did not come with the metal clips on the caliper bracket, you can reuse the old ones if they are not damaged. Be careful removing them as they will bend easily. Carefully pry them off the bracket with your screwdriver.
When to replace front brake pads and rotors?
Years: 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005. Genuine OEM Mercedes-Benz Front Rotors. Check fitment. Before you start replacing parts it is a good idea to inspect the condition of the pads and rotors. While brake pads are easy to inspect, rotors require that you measure the thickness of the disk to see if it is within limits or not.
How to install brake pads step by step?
Make sure to apply brake lubricant at the slider contact points before installing the hardware. Note the wear-sensor position orientation to install the pads correctly. Different pads have varying wear-sensor placement. Some pad sets have wear sensors on just the inner pads, some on all four pads, and some do not have wear sensors.
Where are the brake rotors on a Mercedes Benz?
Identification of the braking system components. To determine if your brake rotor is in specification, locate the minimum thickness stamp on the rotor. It may be on the front, back, or side. The spec will most likely be listed in millimeters.
Where are the brake master cylinders on a Mercedes C class?
C-Class brake master cylinder. Move to the right rear brake caliper and unbolt the brake wear sensor from the caliper. The bolt is 8mm. These are typically only found on the passenger side, but there is a variance between models and years.
How many brake pads does a Mercedes Benz have?
(1 set per car, contains both left and right pads) Note: For cars with Electronic Traction System, or Acceleration Skid Control (Code 212, or 471). (1 set per car, contains both left and right pads) Note: For cars with Electronic Traction System, or Acceleration Skid Control (Code 212, or 471). (1 set per car, contains both left and right pads)
Where can I find two piece brake pads?
They are found on the p30 c63. There is also a two-piece rotor found on the p31 version. These are three to four times the price, but offer better braking performance. Some aftermarket companies make two-piece rotors as well. The price is typically in the middle, and they are the lighter assembly of the bunch.
“Massage” the caliper’s pistons to get them back into place. Fasten the caliper hub with the large 14mm bolts. Connect the caliper slide pins in place, and give the calipers a good shake to make sure that the pads are fitted properly and not loose. Fit the wheel to the hub and torque the wheel bolts to 90 ft-lbs.
C-Class brake master cylinder. Move to the right rear brake caliper and unbolt the brake wear sensor from the caliper. The bolt is 8mm. These are typically only found on the passenger side, but there is a variance between models and years.
Where to CHECK BRAKE FLUID in Mercedes AMG?
Factory jack point locations, inside the wheelbase of the car. Break your lugnuts loose before lifting the vehicle in the air. This will make removing the wheel much easier. To begin, check the brake fluid level by twisting the cap on the brake fluid master cylinder off.
They are found on the p30 c63. There is also a two-piece rotor found on the p31 version. These are three to four times the price, but offer better braking performance. Some aftermarket companies make two-piece rotors as well. The price is typically in the middle, and they are the lighter assembly of the bunch.