How do you replace an intermediate steering shaft?
Replace the upper intermediate shaft. Install the upper intermediate steering shaft through the dash boot seal and slide the lower end into the steering gear coupling shaft. Raise the upper end of the intermediate steering shaft and install into the steering column shaft.
Can a GM steering shaft fit a GM Truck?
A new GM steering shaft has the updated design, so you should stick with that. This one did NOT fit the lower shaft in the slightest. I had to use my bench grinder and coarse sander to take off some of the metal to get it to fit.
What does GM intermediate shaft p / n 19153614 look like?
This condition may be felt while making low speed turns or on rough road conditions. Intermediate shaft P/N 19153614 has been redesigned to replace previous designed dampened and non-dampened Intermediate shafts and will not look like your original.
Why did I replace my steering shaft on my Silverado?
The original shaft has a telescoping rod, the replacement one does not. I bought this part to fix a clunky steering noise on my 2005 Silverado. I also bought the replacement Dorman bearing as well. After replacing both parts together I no longer have clunky steering.
Turn the steering wheel to expose the bolt on the upper part of the shaft under the dash and use the seatbelt to hold the wheel in position 5. Loosen the upper bolt and re3move it and the nut to free the upper shaft 6. Remove the three 10mm nuts holding the rubber shaft housing that’s mounted on the firewall 7.
What happens when the seal on an intermediate steering shaft breaks?
A broken seal is often the culprit when it comes to a problem with your intermediate steering shaft. This seal is what holds the needle bearings that we mentioned earlier. Where the seal breaks, the needle bearings become exposed and they can lose their lubrication.
What are the symptoms of a bad steering shaft?
Below are five of the most common symptoms of a bad intermediate steering shaft. When the intermediate steering shaft starts going bad, one of the first symptoms that people usually notice is strange popping or clunking sounds coming from the steering wheel each time they turn it.
How does the steering shaft connect to the gear box?
One of those parts is the intermediate steering shaft. It connects the steering wheel with your steering gear box or the rack and pinion in your vehicle. The intermediate steering shaft has what’s called a universal joint on one end which is what allows the shaft to connect to the gear box.
How to replace a steering shaft on a Toyota Sienna?
https://static.nhtsa.gov/odi/tsbs/201… The TSB involves re-greasing the telescoping intermediate steering shaft to cure the noise. In this video, the intermediate steering shaft was replaced with a used one on a 2006 Toyota Sienna front wheel drive. Hammer, (although I recommend an air hammer!) https://www.linkedin.com/company/spee…
How to replace a front wheel drive steering shaft?
The TSB involves re-greasing the telescoping intermediate steering shaft to cure the noise. In this video, the intermediate steering shaft was replaced with a used one on a 2006 Toyota Sienna front wheel drive. Hammer, (although I recommend an air hammer!) https://www.linkedin.com/company/spee… https://www.youtube.com/subscription_… Loading…
Where is the intermediate steering shaft located on a car?
The intermediate steering shaft connects the steering column underneath the dashboard to the steering rack pinion underneath the vehicle. It is comprised of a telescoping shaft with two universal joints to account for a steering column tilt angle and collapsibility.
Below are five of the most common symptoms of a bad intermediate steering shaft. When the intermediate steering shaft starts going bad, one of the first symptoms that people usually notice is strange popping or clunking sounds coming from the steering wheel each time they turn it.
Take the new intermediate shaft and insert it into the yoke sleeve. Make sure the flat spot is at 12 o’clock for the bolt to go through, then remove the bolt. Place the lower bolt into the sleeve and make sure it can thread in. The lower attachment has a 360* gap in the splines for the bolt. Make sure the wheels are still pointed straight forward.
How do I remove the steering column cover?
Remove the screws for the lower steering column cover with a screwdriver if the cover has screws. Otherwise, grasp the bottom steering column cover and squeeze it lightly to remove it from its clips and detach it from the column.
Where can I get A Tacoma 4WD steering shaft replacement?
This replacement requires no special tools or skills. For a 2005-2015 Tacoma 4wd the Lower Steering Shaft part number is 45203-04021 . – Available form online Toyota parts outlets for about 150-175. Seeing that my Tacoma is more than a bit over the hill I opted for aftermarket parts.