How do you remove the fan from a water pump?
Screw off the bolt (s) on top of the fan shroud using a socket wrench. There may be a couple bolts, or there may be one large one on the front. Slide the fan clutch off the front of the water pump and lift it out of the engine compartment. Cool off the engine completely before you attempt to remove the fan clutch.
How do you turn off a water pump?
Step 1 Position the strap wrench to the water pump’s pulley to keep the pulley from turning while you take off the bolt on the front of the water pump where the fan clutch is attached. Loosen the large nut on the front of the water pump by turning it counterclockwise with a wrench. You may have to hit the wrench with a small mallet to get it going.
What’s the best way to fix a water pump?
Position the strap wrench to the water pump’s pulley to keep the pulley from turning while you take off the bolt on the front of the water pump where the fan clutch is attached. Loosen the large nut on the front of the water pump by turning it counterclockwise with a wrench.
Do you need to remove radiator to replace water pump?
Your vehicle’s repair manual will tell you which components you’ll need to remove to get to the car water pump. On some engines, you may need to remove the radiator, shroud and hoses to access the water pump. You may also need to remove the fan, pulleys and harmonic balancer, which will require a specialized puller.
Screw off the bolt (s) on top of the fan shroud using a socket wrench. There may be a couple bolts, or there may be one large one on the front. Slide the fan clutch off the front of the water pump and lift it out of the engine compartment. Cool off the engine completely before you attempt to remove the fan clutch.
Step 1 Position the strap wrench to the water pump’s pulley to keep the pulley from turning while you take off the bolt on the front of the water pump where the fan clutch is attached. Loosen the large nut on the front of the water pump by turning it counterclockwise with a wrench. You may have to hit the wrench with a small mallet to get it going.
How can I loosen the nut on my water pump?
Loosen the large nut on the front of the water pump by turning it counterclockwise with a wrench. You may have to hit the wrench with a small mallet to get it going. If it doesn’t turn, then try to turn it clockwise.
Position the strap wrench to the water pump’s pulley to keep the pulley from turning while you take off the bolt on the front of the water pump where the fan clutch is attached. Loosen the large nut on the front of the water pump by turning it counterclockwise with a wrench.
How do you remove a fan from a Jeep Cherokee?
Remove the fan and clutch assembly from the engine compartment. Remove the bolts and nuts that attach the fan to the clutch by turning the bolts counterclockwise with the wrench.
How do you change the water pump on a jeep?
Loosen the four water pump pulley bolts, using the wrench, and remove the drive belt by simply lifting it off the pulley. Remove all the hoses from the water pump by detaching their clamps. If they’re stuck, twist them with the pair of pliers to break the seal and pry them off.
How to remove cooling fan from Jeep garage?
1. Clean gasket mating surfaces. 2. Using a new gasket, position water pump and install mounting bolts as shown. . Tighten water pump mounting bolts to 58 N•m (43 ft. lbs.) torque. 3. Spin water pump to be sure that pump impeller does not rub against timing chain case/cover.
How to remove a water pump from a jeep?
3. Remove accessory drive belt (Refer to 7 – COOLING/ACCESSORY DRIVE/DRIVE BELTS – REMOVAL). 4. Remove lower radiator hose clamp and remove lower hose at water pump. 5. Remove seven water pump mounting bolts and one stud bolt. CAUTION: Do not pry water pump at timing chain case/cover.
How to remove water pump from 4.7L engine?
The water pump on 4.7L engines is bolted directly to the engine timing chain case/cover. A gasket is used as a seal between the water pump and timing chain case/cover. The water pump can be removed without discharging the air conditioning system (if equipped). 1. Disconnect negative battery cable from battery.