How do you make photo coasters waterproof?

How do you make photo coasters waterproof?

You’re going to want to coat the image and coaster with at least three coats of Mod Podge, allowing it to dry for 15 minutes (or until clear) between coats. Once the final coat has dried, spray all of the coasters with a clear acrylic gloss spray, which ensures that they’re waterproof/drink proof.

How do I make tile coasters?

1. Step 1: Cut the Paper. Cut your paper, or photos, to 3.5″ square.
2. Step 2: Glue Paper to Tile. Using the Mod Podge and brush, glue the scrap book paper to the center of a tile.
3. Step 3: Apply Mod Podge over the Top. Cover the top of the tile with a layer of Mod Podge.
4. Step 4: Cut & Apply the Felt.
5. Step 5: Seal the Coasters.

How do I turn a photo into a coaster?

How to Make DIY Photo Coasters

1. Step 1: Paint the edges of the tiles.
2. Step 2: Trim your photos down for your DIY photo coasters.
3. Step 3: Glue photos to center of tile.
4. Step 4: Prepare the resin.
5. Step 5: Spoon out resin onto your DIY photo coasters.
6. Step 6: Repeat for each tile.
7. Step 7: Get rid of the little bubbles.

How do you transfer pictures to coasters on tiles?

Cut your photo so that there’s minimal white space around the edges. To prep the tiles, wipe with a damp towel to remove any dust. Brush a light coat of Mod Podge on both the tile and on the photo (the front of the photo, NOT the back). Place the photo onto the tile, taking care to line up the photo with the tile.

How do you hang pictures on tile?

How To Hang Photo Tiles

1. Step 1: Experiment with different layouts on the floor before you hang your tiles.
2. Step 2: Use a tape measure or ruler to keep the spacing of your tiles uniform.
3. Step 3: Remove the backing from the adhesive tape.
4. Step 4: Using your hands, apply light, even pressure to the face of the photo tile.

How do you waterproof tile coasters?

Apply 2 coats of a clear spray sealer to the coasters to seal and waterproof them. Make sure to do this in a well ventilated area. Spray the top, sides, and bottom side. Let the sealer dry for 20 minutes or so.

What kind of paint do you use on tile coasters?

Sometimes I get asked how to make coasters by directly hand-painting on them, so here’s how: You can paint on your tiles using special oven-bake ceramic paint like the Pebeo Vitrea paints, bake them (using the instructions that come with the paint), and then coat the tiles with envirotex like I describe on the rest of …

Can you use tiles as coasters?

Making coasters from tiles. You don’t even need special equipment, just your spare tiles, PVA glue, and Sharpies or pictures or photographs. It’s also a good idea to use felt, cork or sticky felt pads to put on the back of the tiles to protect your table surfaces.

What can I use to back tile coasters?

Felt, Fleece or Cork scraps for backing + Hot Glue to attach the backing Paint the rough, unfinished side edges of the coasters. Once the tile has dried, grab your photos… {black and white photos are also fun to use on this craft!} Trim photo into a square shape, to fit the tile. Now, be sure not to rush the project, and give it plenty of time.

What should I do with my photo coasters?

Package them up, give them as gifts, or put them to good use in your own home. The tile coasters above are going to be an engagement gift for a friend. The resin is tough and protects your photos well. It also makes for easy clean up- just wipe them off with a damp cloth if they get any stains on them.

How do you glue a photo to a tile?

Paint a thin layer of Mod Podge directly onto the back of your photo (edge to edge) and stick the photo to the tile. You are basically using the Mod Podge as a glue. Make sure you press down on all four corners to ensure the photo isn’t peeling up around the edges. Allow this to completely dry before moving to your next step.

How long does it take for photo coasters to dry?

For a thin coat such as this, it will take between 48-72 hours for a full cure. Within 24 hours you should be able to handle them. However, we recommend to wait the recommended time to insure they are completely dry and you don’t leave any dings on your photo coasters.