How do you disconnect a throttle wire plug?
Shown here is a disconnect tool that you use by inserting it into the round hole next to the pin hole. Press it down until you here a “click”. At this point you have disconnected the pin. Pull the wire out of the plug at this point.
How to remove throttle by wire plug Road 6 customs?
Remove one wire at a time, moving the tool to the next wire one by one. When you are ready to put it back together simple put the wires back in where they came out and push the white cap back down to lock them in place. You’re done!
How to repair a wiring harness and throttle position sensor?
Plug in the wiring harness connector if you are not going to change it. Cut the wires on the pigtail about 1 inch away from where they enter the main wiring harness. Strip about 1/2 inch of the insulation off the wires at the main wiring harness connector. Insert each one of the bare wires into a separate butt connector.
What kind of throttle connector do I need for Schwinn S1000?
High Performance 24V Control Module for 500-750 Watt Motor Model: XK-022C . Currie 36 Volt 30 Amp Controller – with 5 Pin Throttle Connector for Schwinn S1000, S750, Ezip E1000 & Izip i1000 Electric Scooters.
Why do you need a throttle body part?
Throttle Body Parts. Your throttle position sensor (TPS) constantly reports the position of your throttle plate (or butterfly valve) to the engine control unit (ECU), helping to control transmission shift points and fuel metering.
What are the connectors for an ebike throttle?
If you are new to ebikes? the first time you see this, it can give you a huge headache. For those ebikers just starting out, this article will cover connectors for the three phase wires for the motor, the hall-sensors, the throttle…plus, the ignition wire (either hot-wired, or attached to an on/off switch).
How does throttle body connect to gas pedal?
An electronic throttle body (or electronic throttle control) connects to the gas pedal/accelerator electronically without the use of cables.
What does the throttle position sensor do on a car?
Throttle Body Parts Your throttle position sensor (TPS) constantly reports the position of your throttle plate (or butterfly valve) to the engine control unit (ECU), helping to control transmission shift points and fuel metering. A failed TPS can mean delayed shifts, poor fuel management or even a no-start condition.
What causes throttle body harness to stop working?
Disconnect the throttle body harness connector, check the connector for any corroded, pushed out, spread or damaged terminals that can cause an intermittent connection. An intermittent loss of signal from one of the sensors may cause this DTC to set without setting a sensor fault.
How do you replace a throttle control motor?
ETC Motor Replace the throttle body, disconnect the battery when the replacing the throttle body assembly. After installation is complete, use a scan tool and select the ETC RELEARN function. Turn the ignition on, with the scan tool start the engine and test drive the vehicle. With the scan tool read DTCs. Did the DTC return? Yes, go to step 5.
What happens when you unplug throttle position sensor?
Car won’t accelerate, lacks power when accelerating, or accelerates itself. Engine won’t idle smoothly, idles too slowly, or stalls. Car accelerates, but won’t exceed a relatively low speed, or shift up.
Shown here is a disconnect tool that you use by inserting it into the round hole next to the pin hole. Press it down until you here a “click”. At this point you have disconnected the pin. Pull the wire out of the plug at this point.
What are the connectors on GM Electronic throttle body circuit?
Well, one is identified, in the service literature, as connector C1 and when you unplug it from the PCM, the part that houses the metal female terminals is a clear Blue color. The second connector is known, in the service literature, as connector C2 and the part that houses the female terminals is a clear Green color.
What to do if your throttle is not working?
If you feel the throttle body has no issues and you do not see any faults in the throttle body, but still you are getting the throttle failure signs, then you can try with resetting the throttle part. The throttle system works with the electrical connection of the engine, and it may get incorrect trouble codes in the electrical functions.
What causes the electronic throttle body to break?
The second most common problem I’ve seen, is the Electronic Throttle Body’s connector having a copper wire break inside the insulation at the point where the wire enters the connector. Since the insulation, of the wire itself, doesn’t break, you don’t realize there’s a problem.