How do you disassemble a Pontiac V-8 engine?
Before disassembly begins, remove the flexplate from the engine while it is suspended from the hoist. This prevents damaging it or the ring gear while bolting it to an engine stand. It can be difficult to apply sufficient torque to remove the bolts while the engine is hanging loose.
Is it possible to remove an engine from a Pontiac?
Though the fluids were drained before removing the engine from the vehicle, a certain amount inevitably remains in its internal passageways.
How do you remove an engine from a Grand Am?
Grand Am Engine Removal Tips If you are removing the transmission at the same time as the engine, many Grand Ams will require you to pull the assembly out from the bottom of the car. The vehicle will have to be hoisted into the air and then the engine can be removed from the bottom.
How does the intake manifold work on a Pontiac?
Pontiac intake manifolds are sealed to the timing cover and use a rubber O-ring and a long bolt. The intake is used as a bypass to circulate coolant throughout the engine while the thermostat is closed during warm-up.
How do you replace a half shaft on a Pontiac Grand Prix?
You can remove and replace a Pontiac Grand Prix half-shaft in a few hours. Determine which CV half-shaft needs to be replaced. (driver’s side or passenger’s side). Break the lug nuts loose on the appropriate wheel using the tire wrench. Do this by placing the wrench over the head of the lug nut and turning it counterclockwise.
Where is the front jack on a Pontiac Grand Prix?
The front jack point of the Grand Prix is located near the radiator and is an extension of the frame of the car. Finish loosening and removing the lug nuts. Take the wheel off and set it aside. Unbolt both the top and bottom bolts on the brake caliper and secure it to the coil springs above it with the zip ties.
How big should the lug nuts be on a Pontiac Grand Prix?
Lower the car onto the ground and finish tightening the lug nuts to 100 ft lbs using the torque wrench. Your Grand Prix lug nuts can be tightened to a minimum spec of 75 ft lbs, but 100 lbs is recommended. I am a Registered Financial Consultant with 6 years experience in the financial services industry.
How many horsepower does a Pontiac engine have?
Pontiac Engines Lit CID Year 6.6 400 1967-1979 6.6 403 1977-1979 6.9 421 1961-1969 7.0 428 1967-1969
How long does it take to remove an engine from a Pontiac Bonneville?
Removing the engine in your Pontiac Bonneville, with the right tools and correct knowledge, should take part of a day. Whether your engine locked up, burned out, or you want to replace it with something with more power or better gas mileage, removing an engine can be hard work, so you might want to have a friend help you.
What’s the best way to assemble a Pontiac engine?
You can also use residue-free solvents and lint-free cloths to wipe contact surfaces just prior to assembly. You can never be too clean when building any engine! A Fel-Pro number-2806 Gasket Kit contains virtually every gasket required to completely assemble a typical Pontiac engine.
Before disassembly begins, remove the flexplate from the engine while it is suspended from the hoist. This prevents damaging it or the ring gear while bolting it to an engine stand. It can be difficult to apply sufficient torque to remove the bolts while the engine is hanging loose.
Though the fluids were drained before removing the engine from the vehicle, a certain amount inevitably remains in its internal passageways.
What kind of coolant does a Pontiac 400 have?
For instance, early engines utilized a reverse-flow coolant system, and the rocker system of engines through the mid 1960s was oiled through its studs. This particular 400 contains neither, and as such, the disassembly steps shown do not touch on them.
Pontiac intake manifolds are sealed to the timing cover and use a rubber O-ring and a long bolt. The intake is used as a bypass to circulate coolant throughout the engine while the thermostat is closed during warm-up.