How do you adjust the clutch on a Honda CRV?
Press the clutch pedal to the floor. Release the clutch pedal 10 – 16 mm (0.39 – 0.63 in.) from the fully depressed position, and hold it there. Adjust the position of the clutch interlock switch (K) so that the engine will start with the clutch pedal in this position.
How do you change the clutch on a Honda CRV professional?
Put a small dab of high melting point grease – not a copper-based product – on the first motion shaft splines, and make sure the new driven plate slides freely back and forth. This not only spreads the grease evenly, but also makes sure you have the correct kit.
When did the Honda CRV professional come out?
The Honda CR-V was launched in 1995 and is a popular multi-purpose vehicle. Now onto its fourth generation, this handy guide should prove to be a worthwhile read for any garage in the UK aftermarket faced with clutch replacement on the third generation 2.2 CDTi model.
What do you need to repair Honda CRV professional?
No special tools are required to complete the repair, but you need to support the engine, gearbox and subframe. We used four transmission jacks, but you could use two jacks and some rope to support the subframe.
Slacken the two bolts from the gearbox mount and remove. Before raising the vehicle, remove two bell housing bolts from the top of the gearbox. The bolt closest to the bumper is in a slightly tricky position and holds in place a wiring harness (Fig 5 below). Remove both front wheels and raise the vehicle.
The Honda CR-V was launched in 1995 and is a popular multi-purpose vehicle. Now onto its fourth generation, this handy guide should prove to be a worthwhile read for any garage in the UK aftermarket faced with clutch replacement on the third generation 2.2 CDTi model.
No special tools are required to complete the repair, but you need to support the engine, gearbox and subframe. We used four transmission jacks, but you could use two jacks and some rope to support the subframe.
What’s the DMF number on a Honda CRV?
The DMF should also be tested for free play and rock between the primary and secondary masses. LuK tool number 400 0080 10 is specifically designed for this purpose on all LuK manufactured DMFs. Full instructions and tolerance data for all LuK DMFs are contained on a CD that comes with this special tool.
Adjust the stroke of the clutch pedal by loosening the lock nut that is the bottom of two on the clutch pedal, and then turn the adjusting bolt until it no longer has any contact with the pedal. Loosen the lock nut that is located on the push rod (found on the top and the side of the pedal).
How do you adjust the clutch on a Honda Prelude?
Turn the push rod either in or out to get the adjustment that you need. Tighten the lock nut on the push rod, tighten the lock nut on the pedal until it touches the pedal, then tighten it 1/4 to 1/2 of a turn more. Look at the place where the master cylinder of the Honda Prelude connects with the pedal.
Where is the clutch adjuster on a Honda Accord?
Look at the top of the clutch pedal, near the pedal point, and you will see the adjuster for the Honda Accord’s clutch there. Turn the adjusting nut on the end of the clutch cable clockwise and test the pedal after each adjustment.
What should the clutch stroke be on a Honda?
Pedal stroke should 0.58 to 0.60 inches, the height of the clutch pedal from the floor should be 0.712 inch, the free play should be .06 to 0.10 inch and the clutch pedal disengagement should be 0.288. Adjust the clutch pedal if it does not fit with the Honda specifications.
Adjust the stroke of the clutch pedal by loosening the lock nut that is the bottom of two on the clutch pedal, and then turn the adjusting bolt until it no longer has any contact with the pedal. Loosen the lock nut that is located on the push rod (found on the top and the side of the pedal).
Look at the top of the clutch pedal, near the pedal point, and you will see the adjuster for the Honda Accord’s clutch there. Turn the adjusting nut on the end of the clutch cable clockwise and test the pedal after each adjustment.
Turn the push rod either in or out to get the adjustment that you need. Tighten the lock nut on the push rod, tighten the lock nut on the pedal until it touches the pedal, then tighten it 1/4 to 1/2 of a turn more. Look at the place where the master cylinder of the Honda Prelude connects with the pedal.
Pedal stroke should 0.58 to 0.60 inches, the height of the clutch pedal from the floor should be 0.712 inch, the free play should be .06 to 0.10 inch and the clutch pedal disengagement should be 0.288. Adjust the clutch pedal if it does not fit with the Honda specifications.