How do I clear my maintenance required light?
How do I reset the “Maint Reqd” light?
- Turn ignition switch to the ON position.
- Set the Odometer/Trip Display to TRIP A mode.
- Turn the ignition switch to the OFF position.
- Depress and HOLD the Trip Meter RESET button while turning the ignition switch to the ON position.
- The Service Maintenance Reminder Light will.
How to reset the maintenance required light on a 2004-2009?
Press the ODO/TRIP button under the display in the center of the dash until odometer reads the mileage (not Trip A or Trip B) 3. Turn the power to the “OFF” position by pressing the power button once while *not* stepping on the brake pedal.
How do you reset the maintenance required light on a Prius?
2015-2020 Prius (OIL RESET) Maintenance Required Indicator Reset STEP 1. Push the START BUTTON, don’t start the ENGINE (Accessory Mode Only) STEP 2. First Clear the System message by pressing the BACK Button on Driver Info Button.
When does maintenance required light go back to zero?
Since you have manually reset the maintenance required light, its counter is back to zero. It will continue to count miles from the odometer until the 5,000 miles mark is reached. Once this happens, the light will again appear on your dashboard.
What does the maintenance required light on a Toyota mean?
This Japanese automobile manufacturer is known for producing some of the most reliable vehicles in the world, but sometimes, even Toyotas flash a maintenance required light on their dashboard. This is true for all new Toyota models and it’s a light the driver shouldn’t ignore. Have you seen the light flashing on your car’s dashboard as well?
How do you reset the Mant. required light?
- Turn ignition switch to the ON position
- Trip Display to TRIP A mode
- Turn the ignition switch to the OFF position
- Depress and HOLD the Trip Meter RESET button while turning the ignition switch to the ON position.
How do I reset the maintance light?
Here’s how you do a maintenance light reset: Put your key in the ignition. Turn the key to position one. This is the position just before starting the car. Push the trip meter reset button on the dashboard. Hold it down for a second or two. Continue to hold the odometer button for around ten seconds. The light should flash, beep, and then go out. Once off, release the odometer button. Start your car.
How can you reset the service light?
- but don’t start the engine.
- Press the button on the lower left part of the steering wheel. The display panel will tell you why the vehicle needs servicing.
- Find and press the reset button on the left side of the instrument panel.
How do you turn off the maintenance required light on a Toyota Sienna?
Turn your ignition key to the ‘ACC’ or ‘LOCK’ position. Press and hold the trip meter reset nob (next to your Toyota Sienna’s odometer). While holding the trip meter reset nob, turn the ignition to ‘ON’, but do not start your Toyota Sienna. Hold the meter reset until the MAINT REQD light switches off.
What if maintenance required light?
The Toyota maintenance light can appear on your dashboard as “MAINT REQD”. It’s a light that remains active permanently, letting you know that you need to go for an oil change in a certified auto shop. Changing the oil in your Toyota can improve fuel efficiency and make your vehicle run as smooth as silk.
Why is my maintenance required light blinking?
It’s basically just telling you that your car will need some kind of scheduled service soon. It could be an oil change, a tuneup, or maybe you need a new timing belt. The maintenance required light may being flashing 500 miles before your car is due for service.
What does the “maintenance required” light mean?
The maintenance required light (maint reqd) indicates that factory service interval has been met. These intervals happen at different mileage or time intervals (typically 5000 miles/6 months).
How do you reset the maintenance required light?
Turn of Maintenance Required Light. Here’s what to do: With the car off and key out, hold in the odometer select/reset button. Insert the key and turn to the run position without starting the car. Keep holding the button in. The Maintenance Required Light will blink once and then in another 5-10 seconds.
How do I reset the required maintance light?
Turn ignition switch to the ON position
- Trip Display to TRIP A mode
- Turn the ignition switch to the OFF position
- Depress and HOLD the Trip Meter RESET button while turning the ignition switch to the ON position.
How do I reset maintenance light?
Turn your vehicle’s ignition to the “acc” setting while holding the button. Do not crank the vehicle. Hold the position for five seconds and turn the ignition key off. Release the button. The maintenance light will be reset and will illuminate again the next time service is due.