How can I reset the airbag light on my Mitsubishi?
You can reset the airbag light on your Mitsubishi right from your home garage or driveway, saving yourself time and money. The airbag light will illuminate on the instrument panel as “SRS,” which stands for “Supplemental Restraint System.”. Usually this light only turns on when the vehicle has been in an accident.
How to repair Mitsubishi L200 air bag code 41?
This page is about Mitsubishi L200 air bag problem code 41. #41 Airbag Code Repair order (“Recheck SRS at each replacement.”) Visually check the wiring harness connection. Replace the harness if it has visible damage. Replace side air bag module (LH). (Before disposal, it must be deployed.) Replace the diagnosis sensor unit.
Is there a diagnostic code for a Mitsubishi L200?
You might need to buy a scanner online which will show Mitsubishi trouble codes and clear the warning light for good. If you need to reset a dashboard light or diagnose a fault on your Mitsubishi L200/Triton we would advise you to go for the iCarsoft i909 Mitsubishi OBD Code Reader.
Which is launch CRP for Mitsubishi L200 air bag light?
For the record I used a Launch CRP129 with current 2017 official software v11.30. Like the OP, I had replaced the AIRBAG clockspring successfully – you know this is correctly done when the DTC for B1401 Driver’s Airbag squib ACTIVE changes to B1401 …….
Is the Mitsubishi L200 air bag light still on?
Hi, I have got a 2008 l200 with the air bag light on. I first replaced the squib with a new one off ebay and the light still remains on. On dissasebling the original squib i found a break in the ribbon cable so confirmed it was broken.
You might need to buy a scanner online which will show Mitsubishi trouble codes and clear the warning light for good. If you need to reset a dashboard light or diagnose a fault on your Mitsubishi L200/Triton we would advise you to go for the iCarsoft i909 Mitsubishi OBD Code Reader.
You can reset the airbag light on your Mitsubishi right from your home garage or driveway, saving yourself time and money. The airbag light will illuminate on the instrument panel as “SRS,” which stands for “Supplemental Restraint System.”. Usually this light only turns on when the vehicle has been in an accident.
How to troubleshoot Mitsubishi SRS airbag warning light?
Turn on the ignition and allow the scanner to power on. Select your Mitsubishi model and year. For example, in 2017, Lancer. Select SRS / Airbag Control unit from the main menu. Select Read Fault Codes. Write down all the codes and also make sure they are NOT PRESENT.
Where is the SRS light on a Mitsubishi airbag?
The airbag light will illuminate on the instrument panel as “SRS,” which stands for “Supplemental Restraint System.”. Usually this light only turns on when the vehicle has been in an accident.
Where is the airbag scanner on a Mitsubishi Lancer?
Plug the Mitsubishi airbag scanner into the OBD2 port under the dashboard, driver’s side. Turn on the ignition and allow the scanner to power on. Select your Mitsubishi model and year. For example, in 2017, Lancer. Select SRS / Airbag Control unit from the main menu. Select Read Fault Codes.
How to reset the SRS light on a Mitsubishi Eclipse?
Wait for the scanner to read the codes and then press “Clear trouble codes” or “Reset” or some similar command to reset the airbag light. Unplug the scanner from the port and start the engine. Verify that the SRS light has turned off. “Mitsubishi Eclipse & Eagle Talon 1995 thru 2005 (Haynes Repair Manual)”; Haynes; 2008
The airbag light will illuminate on the instrument panel as “SRS,” which stands for “Supplemental Restraint System.”. Usually this light only turns on when the vehicle has been in an accident.
Plug the Mitsubishi airbag scanner into the OBD2 port under the dashboard, driver’s side. Turn on the ignition and allow the scanner to power on. Select your Mitsubishi model and year. For example, in 2017, Lancer. Select SRS / Airbag Control unit from the main menu. Select Read Fault Codes.
Wait for the scanner to read the codes and then press “Clear trouble codes” or “Reset” or some similar command to reset the airbag light. Unplug the scanner from the port and start the engine. Verify that the SRS light has turned off. “Mitsubishi Eclipse & Eagle Talon 1995 thru 2005 (Haynes Repair Manual)”; Haynes; 2008