Can a crankshaft sensor be replaced on a Jeep Cherokee?
Replacing the crankshaft position sensor is a hassle, but this article will help to smooth that over. This article applies to the Jeep Cherokee XJ (1984-2001). The crankshaft position sensor (CPS) is a common cause of stalling in the Jeep Cherokee. If the PCM fails to receive a signal from the sensor, it automatically shuts off the engine.
How to replace crankshaft on Jeep Cherokee XJ?
Light up the back of the engine compartment so you can see the sensor. Get under the Jeep and look for the small module sticking out the back of the engine. There should be a black electrical harness that makes its way up. To remove it, you’re going have to find the right combination of socket and extensions to access the bolt.
What causes the crankshaft to stall on a Jeep Cherokee?
The crankshaft position sensor (CPS) is a common cause of stalling in the Jeep Cherokee. If the PCM fails to receive a signal from the sensor, it automatically shuts off the engine.
How to replace crankshaft position sensor on Jeep Grand Cherokee?
This is going to be a how to on replacing the crankshaft position sensor on the 4.0L motor in the Grand Cherokee. This is by no means the ONLY way or “correct” way to replace the sensor. This is only the way I changed the sensor.
What’s the crankshaft position sensor on a Jeep Laredo?
Always use O.E.M. if you can afford it or plan to keep it. 1996 Jeep Grand Cherokee Laredo with the inline 4.0 six. 258000 miles. I had problems for years with the “Crankshaft Position Sensor,” crank no start.
Why is my Jeep not cranking at all?
However this one was a failure out of the box. Completely rebuilt everything in the Jeep, new motor, axles, trans, etc…installed all new sensors and ECM, Jeep would crank and run for a few minutes and die. Then wouldn’t crank at all.
Why did I buy a Mopar crankshaft sensor?
I purchased this MOPAR CPS because after 30 years of building Jeeps you learn that the cheap aftermarket CPS are junk. However this one was a failure out of the box. Completely rebuilt everything in the Jeep, new motor, axles, trans, etc…installed all new sensors and ECM, Jeep would crank and run for a few minutes and die.
Always use O.E.M. if you can afford it or plan to keep it. 1996 Jeep Grand Cherokee Laredo with the inline 4.0 six. 258000 miles. I had problems for years with the “Crankshaft Position Sensor,” crank no start.
Why is my Jeep Grand Cherokee not working?
The cause of the issue was a short in the crankshaft position sensor that disabled all powertrain and braking systems. All systems share the same 5 volt circuit into pcm. See all problems of the 2011 Jeep Grand Cherokee . The contact owns a 2004 Jeep Grand Cherokee.
How big is a Mopar crankshaft position sensor?
Make sure this fits by entering your model number. Package Dimensions: 7.83 L x 1.55 H x 6.94 W (inches) These items are shipped from and sold by different sellers. Show details Only 1 left in stock – order soon.
Replacing the crankshaft position sensor is a hassle, but this article will help to smooth that over. This article applies to the Jeep Cherokee XJ (1984-2001). The crankshaft position sensor (CPS) is a common cause of stalling in the Jeep Cherokee. If the PCM fails to receive a signal from the sensor, it automatically shuts off the engine.
Make sure this fits by entering your model number. Package Dimensions: 7.83 L x 1.55 H x 6.94 W (inches) These items are shipped from and sold by different sellers. Show details Only 1 left in stock – order soon.
The crankshaft position sensor (CPS) is a common cause of stalling in the Jeep Cherokee. If the PCM fails to receive a signal from the sensor, it automatically shuts off the engine.
How do you replace the crankshaft position sensor?
It’s held in place by two 10mm nuts (see picture below, one nut is hidden just out of view). Remove those by using a 10mm socket on the bottom one and a 10mm wrench on the top one. Then use a screwdriver to gently pry the cover up over the studs.
Is there a crankshaft sensor for Jeep Cherokee?
Shop AutoZone for Jeep Cherokee Crankshaft Position Sensor. 10% OFF $75. Use Code: DIYSAVE10 Online Ship-to-Home Orders Only
Which is the best parts company for Jeep?
For over 25 years, Quadratec has proudly provided Jeep enthusiasts the best parts and accessories available. Our company was founded on one principle: Provide the highest level of service and top quality products to all our customers – every day.
What’s the name of the new Jeep Wrangler?
You will see Wranglers (JK, TJ and YJ), Cherokees (XJ), CJs, Grand Cherokees (WK, WK2, ZJ, WJ) and even the new Cherokee KL. Questions? Give us a call. And while you are at it, check out our Torque Blog and subscribe to our popular YouTube Channel.
How do you install CPS on a Jeep Cherokee?
Remove the old CPS and cable from the Jeep. Install the new CPS in the location that you removed the old one from, using the two 7/16-inch bolts. Route the cable from the new CPS up to the clip on the bell housing and install the cable under it.
Where is the CPS on a 2001 Jeep Cherokee?
The 2000 and 2001 will have the CPS in the same location on the bell housing, but the wire connector may be on the passenger side, not as shown in the diagram below. Simply follow the wire from the sensor to the connector. . Bob likes this.
Is there a 2001 Jeep Cherokee that will not start?
Discussion in ‘ Cherokee ‘ started by jim14424, Aug 22, 2016 . I have a 2001 Jeep Cherokee limited, that will crank but will not start. I have replaced the crankshaft position sensor, and the camshaft position sensor. I do have fuel getting to the engine, but no spark. I check the coil pack, but do not see spark.
What does the CPS do on a jeep?
The CPS is responsible for reading the location and speed of the crankshaft and sending that information to the Jeep’s central processing unit (CPU), where the information is used to calculate spark timing for the ignition system.
Where is the CPS on a Jeep Cherokee?
Trace the cable from the CPS to the the top of the engine and locate the weather-proof connector where it plugs into the main wiring harness. Unplug the connector, being careful not to break the tab on the connector. Remove the old CPS and cable from the Jeep.