Why does my motorbike engine make a noise when I start it?
Start out by listening at different points around the engine, like the cylinder head valve caps, or the camchain tensioner mechanism. An engine will often sound noisy on start-up because components aren’t under load, the engine is cold and the oil hasn’t warmed up and started circulating freely.
What kind of noise does a bad wheel bearing make?
Noise can be misleading: a humming noise while driving can be caused by several different issues, starting with your tires, but it can also be the wheel bearing or CV joint. The classic sounds of a bad wheel bearing are cyclic chirping, squealing and/or growling noise.
Are there any problems with the Kawasaki Vulcan 900?
This issue occurs most often on the Kawasaki Vulcan 900. The drive pulley on the Vulcan drives the belt, and most owners facing the problem experience noises coming from the belt. When it comes to these Drive Pulley problems on the Vulcan, it can indicate issues with different components.
What makes a Vulcan 900 make a squealing noise?
Problems with the drive pulley will usually show themselves as noises coming from the belt. It sounds like the belt is rubbing up against something and producing a squealing noise. Owners of the Vulcan 900 who came across this problem stated that it showed up after the bike had fallen or had gotten into an accident.
Are there any issues with the Kawasaki Nomad?
I read they have issues,anyone out there who has a 09 or 2010 ,please advise if you have any problems. Transmission clunks belt whine, excessive heat from pipes or engine. I would appriecate any feed back .
Why does my nomad not make belt whine?
I understand that the key to not having belt whine is to make sure you have perfect alignment of the front and rear wheels so the belt is centered in the pulleys. After the break in period, using synthetic oil should calm down some of the transmission noise. The transmission is a bit clunky shifting from first to second gears.
This issue occurs most often on the Kawasaki Vulcan 900. The drive pulley on the Vulcan drives the belt, and most owners facing the problem experience noises coming from the belt. When it comes to these Drive Pulley problems on the Vulcan, it can indicate issues with different components.
What’s the difference between a 98 and a 09 Nomad?
The handling of the two bikes is significantly different. the ’09 almost feels “sporty” and corners much better than the ’98 does, but then 11 years of engineering can have that effect.
Start out by listening at different points around the engine, like the cylinder head valve caps, or the camchain tensioner mechanism. An engine will often sound noisy on start-up because components aren’t under load, the engine is cold and the oil hasn’t warmed up and started circulating freely.
Why does my car make a sputtering noise when I accelerate?
When an engine is tuned correctly, it typically sounds smooth and definitely not choppy. As the engine accelerates, the engines harmonics are equally smooth. A sputtering engine will rise and fall rapidly, may have periods of stalling or rapid acceleration or deceleration. What causes this sound?
Why does my car make a clunking noise when I shift gears?
Broken or loose transmission or engine mounts cause the transmission to move… If your transmission mount or engine mount becomes loose or breaks, you may hear clunking noises whenever you make a sudden change in speed or whenever you shift gears, due to the movement of the unsecure mount.
Why does my car engine sound like it’s going to fall off?
If your car engine sounds like the bottom end is going to fall off, it’s probably engine rod knock. The noise you hear is like a ball peen hammer tapping on a steel plate repeatedly. What’s actually happening is measured in thousandths of an inch.
What should I do if my motorcycle won’t start?
If the reading stays steady, your battery is good to go—and your motorcycle likely has another problem (or a few problems). Fortunately, there are other troubleshooting means that can help determine why your bike won’t start.
Why does my motorcycle not start with the side stand down?
Newer bikes (and some older ones) may refuse to start with the side stand down. Along with all the other high-tech sensors that are on board, your motorcycle might have a built-in code that keeps the ignition from starting if your kickstand is engaged.
Why do I hear a clicking noise when I start my riding mower?
The clicking noise comes from a part called the starter solenoid. The solenoid connects the battery to the starter motor when the solenoid is energized. The key switch and the safety switches in the starter circuit combine to energize the solenoid. If the solenoid is clicking, the circuit that triggers it is working.
Why do I Hear No sound when I start my car?
When you try to start your car, you may hear no sound at all. This silence may be due to electrical issues: A discharged or failed battery A failed system component (for example, relay or safety switch)
Why do I hear silence when I start my car?
This silence may be due to electrical issues: 1 A discharged or failed battery 2 A failed system component (for example, relay or safety switch) 3 Corroded electrical connections (including battery terminals) that prevent electrical current from reaching the starter motor.
What are the hand gestures on a motorcycle?
Following are the five main hand gestures you may encounter: 1. The Nothing – This is the “default” hand position of most cross-encounters.
Are there any tricks you can do on a motorcycle?
Listen closely, Grasshopper… Here are 10 handy little motorcycle riding tricks that will make you smoother, safer and, in some cases, faster. They’ll work on any bike, any time, whether you’re cruising, tearing up a mountain road or heading out around the world.
What do you say with your left hand on a motorcycle?
The Geek – Left hand raised high in the air as if to say, “Hi mom!” This one is specifically reserved for the new rider, who is “SO excited to be one of the gang!” Also may be seen being used by Moped or scooter riders. Recommendation: Just don’t.
What should I do if my motorcycle is sputtering?
Start by checking the easiest spot first which would be the spark plugs. Take out your spark plugs and make sure there is no nasty build up on them or any type of corrosion. Also make sure the point isn’t worn down and that the gap between the center and the ground electrode is the appropriate distance.
How to tell if your motorcycle has a lean mixture?
Typical symptoms of a lean mixture are: 1 Backfiring as the throttle is closed (primarily during coast-downs) 2 Lurching acceleration 3 White or light gray spark plugs 4 Requiring excessive amounts of choke to run/start 5 White or light gray muffler end pipes 6 Bluing (on chrome systems) of the exhaust header down-pipes
What causes a motorcycle to have an explosion?
Other culprits could include corroded or cracked spark plugs or spark plug wires, a faulty ignition coil, a clogged air filter, or engine timing issues. The three things you need to create an explosion in the combustion chamber of a motorcycle are air, fuel, and a spark.
Why does my car rattle on cold start?
If you hear engine rattle noise from your engine on cold start, and the engine rattle noise goes away after a few seconds, and the engine rattle noise comes from the side of the timing cover we will explain what could cause that. Most new engines nowadays are equipped with timing chain.
Why does my Harley Davidson make a knocking noise?
Twin cam engine cutaway. The crankshaft flywheels in the twin cam engine are pressed together and have the potential to twist or slip, which will cause a knocking noise in the bottom end or near the gear case; plus, a much more noticeable engine vibration.
When does the noise in the engine go away?
And, the noise itself is NOT present until crossing the 2500 rpm range. It enters as a sort of ‘cackle’ sound that begins at about 2600 to 2700 rpm, and essentially remains present up to about 3500, and then diminishes and is gone by about 4K. It is directly related to throttle pressure and ‘load’ as presented by the terrain and conditions.
Twin cam engine cutaway. The crankshaft flywheels in the twin cam engine are pressed together and have the potential to twist or slip, which will cause a knocking noise in the bottom end or near the gear case; plus, a much more noticeable engine vibration.
What causes a knocking noise at the bottom of the engine?
Bottom-End (Crankshaft) Noise. The crankshaft flywheels in the twin cam engine are pressed together and have the potential to twist or slip, which will cause a knocking noise in the bottom end or near the gear case; plus, a much more noticeable engine vibration.
How to diagnose engine noise in a motorcycle?
The first step in diagnosing an engine noise is to narrow down which area the sound is coming from and under which conditions the noise occurs. A mechanic’s stethoscope is a great tool to use when diagnosing engine noises, as the probe can reach into tight places to monitor the sounds of the engine.
Why does my 103 motor make a clunking sound when I turn it off?
Some 103 motors tick a little worse than others. It’s really not anything to be overly concerned about. Make sure that you are running a quality oil. We like Spectro oils best. The clunking sound that you hear when you turn your bike off is your compensator assembly. It is a poor design.