Why are my wipers not working on my Mercedes?

It is common for the fuse to burn out if you press the window switch to active the wipers, but the wipers have frozen, or there is snow on the windshield. Replacing the fuse may be all that you need to do to fix the wiper problem on your Mercedes-Benz.

What are the most common windshield wiper problems?

Mercedes Wiper Problems Go to top 1 I- Windshield wiper motor runs, but the arms don’t move. 2 II- Turn Signal, Horn, Wipers all have stopped working. 3 III- Installed new wipers and the wipers stopped working. 4 IV- Wiper hesitates to move or move very slowly. 5 V- Mercedes Windshield Wipers work erratically. …

Why are the wipers, heater, and headlights not working?

One day, I’ll turn the car on, and the wipers, blower, and turn signals do not work. Sometimes I drive for 15 minutes, and they all come on. Sometimes they don’t. Every time I’ve taken the car in for service the problem goes away before I get to the dealer, and they tell me they can’t do anything about it if they can’t replicate the problem.

Where are the fuses on a Mercedes windshield wiper?

Your Mercedes-Benz has three to four fuse boxes. They are located on the side of the dashboard, engine bay, rear seat or even in the trunk. Find the fuse chart for your car and locate the corresponding fuse for the windshield wiper motor. Make sure the fuse is not burned out.

What does it mean when your windshield wipers stop working?

When the switch is engaged, the motor rotates, and a network of linked arms, connected by several pivot points, converts this rotation into the back-and-forth motion of the wiper blades. When your wipers stop working, it is a good sign that one of these critical elements is damaged or broken.

Is it safe to use windshield wiper blades in snow?

While windshield wipers are capable of removing light snow and ice, they are not designed to clear away heavy snowfall or ice frozen onto the windshield. If you decide to use your wiper blades for this reason, then you risk damaging the blades.

The wipers won’t work if the hood is not closed. If it’s not that, does the washer work? If the washer sprays but the wipers don;t swipe, then it’s the motor or wiring or fuse to the motor.

When do windshield wipers stop working but can hear motor?

It’s an alarming experience when your wipers stop working in a heavy downpour, especially at highway speeds. You don’t miss wipers until they don’t work. Windshield wipers not working but can hear motor? When your wipers stop working, and you can hear the wiper motor running. The problem is most likely a disconnected wiper motor link arm.

How are the wipers attached to the car?

The motor, wiper drive mechanism and wiper arms are all attached to it. When activated a wiper motor rotates continuously and more sophisticated motors rotate left to right. The challenge is to transform rotational movement of the wiper motor into lateral movement of the wipers blades.

What happens when the wiper motor is activated?

When activated a wiper motor rotates continuously and more sophisticated motors rotate left to right. The challenge is to transform rotational movement of the wiper motor into lateral movement of the wipers blades.

What causes my windshield wipers to stop working?

When your wipers stop working, and you can hear the wiper motor running. The problem is most likely a disconnected wiper motor link arm. Refitting the link arm is usually a simple process. You’re lucky, this is a pretty simple job, however some cars are easier than others.

How are the wiper spindles attached to the motor?

Link rods are attached to the wiper motor and also to the wiper spindles. They are attached by a bushing, commonly a plastic socket on the link rod, a metal ball on the motor and wiper spindle. The plastic bushings simply wear out and refitting it may work for a while but eventually will need to be replaced.

What happens if the intermittent wiper switch fails?

However, when one part malfunctions, it can cause potential safety concerns. One of the most common parts to fail is the intermittent wiper relay switch. The electronic relays that are installed in today’s cars, trucks and SUV’s have to operate in very hot and grueling conditions or are subject to constant abuse.

When do I Know my wiper relay is bad?

One of the quickest indicators that a problem exists with the intermittent wiper relay is when the wipers are not intermittent and only work at one speed. The relay switch sends an electrical signal to the module that controls the operation of the wiper motor and gears inside.

When do windshield wiper blades only work one speed?

The windshield wiper blades have one speed. One of the quickest indicators that a problem exists with the intermittent wiper relay is when the wipers are not intermittent and only work at one speed.

Are there rain sensing wipers in Lexus ES300?

Yes…here in Texas we have drizzle too! Lexus “rain sensing” wipers are a JOKE. They suck. I want my ES300 intermittent wipers back. I’m totally disappointed that Lexus would put such a poorly performing feature on their automobiles. It shows that poor engineering and product testing was done before committing to production.

Why are my wipers failing on my Lexus ES?

Here are some potential causes as to why your wipers are failing. This article applies to the Lexus IS, ES, GS, and RX (2005-2013). Wipers should clean the windscreen over most of the visible glass and return to “park” with the wipers stowed.

What causes the intermittent wiper to stop working?

If you make a change in the settings and the wipers don’t react, it’s most likely due to a malfunction in the intermittent wiper relay. This can lead to a potentially unsafe driving situation as sometimes we encounter weather conditions that require the use of the intermittent switch.

When to know if your wiper relay is bad?

Your wiper relay could be bad if the low and high speed wiper positions function properly but the intermittent function stops working. Any combination of positions working or not working is a good indication of a faulty relay. Step 1: Locate your relay. Many late model vehicles can have multiple locations for fuses and relays.

What to do if your windshield wiper is not working?

Make sure that the link between the wipers and the wiper motor is not broken. Next, try tightening the bolt that holds the wiper arm in place. It is possible that there is a problem with the controller area network or the front signal acquisition module (SAM).

What should I use to lubricate my Mercedes wiper?

-a slow wiper movement as the wiper moves on the windshield. You should lubricate the wiper mechanism at the center (bottom) of the windscreen. Remove the cover from the wiper arm and use a lithium grease such as Liquid Wrench White Lithium Grease. Here is a helpful tutorial on how to lubricate windshield wiper mechanism on a Mercedes-Benz.

Why did my Skoda front wipers stop working?

Someone (no names mentioned) recently put bottled water into the car window washer instead of the 50/50 windscreen wiper mix. Of course all was fine until this cold snap hit the South East of England and we have been having sub zero temperatures and rain and snow which froze the water in the pipes and in turn burned out the front window wiper fuse.

Where are the fuses on a Mercedes Benz GL450?

If your GL450 is experiencing electrical problems, you should always check the fuses first, because they are relatively easy to check and cheap to change. Some Mercedes-Benzs have multiple interior fuse boxes including in the trunk – the video above will show you where the interior fuse box of your 2009 GL450 is located.

What causes a wiper fuse to burn out?

That way, if the motor is overloaded for any reason, the fuse will burn out first, instead of the more expensive wiper motor. If the wiper motor fuse burns out, check for any obstructions that may cause the motor to be overloaded.

Where is the fuse on a Mercedes windshield washer?

It could also be in the fuse box under the rear seat in some models. Find the fuse that belongs to the windshield washer fluid motor. Pull it out and make sure it make sure it is not burned out. Use a digital multimeter to check if the power goes to the windshield pump. You need to set your multimeter to measure DC 20-volt mode.

What’s the name of the Mercedes Benz parking light?

Parking light. P21/5W. Front turn signal. P21/5W. Rear turn signal. P21W. Tail light. 5007 or 12821 or R5W. Tail light.

What kind of parts does a Mercedes Benz use?

MERCEDES-BENZ Parts | RockAuto ALL THE PARTS YOUR CAR WILL EVER NEED Show Prices In US Dollars ($)Australian Dollars (AU$)Brazilian Real (R$)Canadian Dollars (CAD$)Swiss Francs (CHF)Euros (€)British Pounds (£)Japanese Yen (¥)Mexican Pesos (Mex$)Norwegian Krone (kr)New Zealand Dollars (NZ$)

Where is the power seat switch on a Mercedes CLK?

Reach the power seat switch on the door of the E-Class / CLK-Class and move the seat all the way forward. Once the seat reaches moves completely forward continue to hold the switch forward for at least 3 more seconds. Move the seat all the way to the back.

Why does the seat move backwards in a Mercedes?

You try to slide the seat backwards and the seat slides forwards. The seat only moves forwards no matter which way you move the switch. This happens because the Electric Seat Adjustment (ESA) control modules (N32/1 left or N32/2 right) which are responsible for controlling the seat no longer remember the limits where the seat can extend.

What causes seat synchronization issue in Mercedes Benz CLK?

This happens because the Electric Seat Adjustment (ESA) control modules (N32/1 left or N32/2 right) which are responsible for controlling the seat no longer remember the limits where the seat can extend. To resolve this problem, we will need to re-synchronise the seats which you can do in a couple of minutes.

Is the frameless side windows on a Mercedes?

Frameless side windows without the B pillars, a still fresh looking exterior, keyless entry door handles which can break and your own personal seat belt butler- which can break as well.

Where is the plug for the windshield wiper motor?

If you are not getting power to the plug that goes into the windshield wiper motor, then you need to do some further troubleshooting. The next item to inspect would be the windshield wiper switch or what is also called the combination switch. The combination switch is located in the steering column.

What are the problems with a Mercedes windshield washer?

Possible Issues 1 Disconnected Washer Fluid Line / Hose (See fix below.) 2 Mercedes washer fluid reservoir leak 3 Defective Mercedes Windshield Fluid Pump 4 Burned out fuse

Why does my windshield wiper blade not move?

For a little while now, the passenger side wiper wouldn’t always move, and when it did, not very far. This kind of problem can often happen in colder areas where the wiper blade freezes to the window and then the driver (me) tries to use them.

Where do you lubricate the windshield wiper on a Mercedes?

You should lubricate the wiper mechanism at the center (bottom) of the windscreen. Remove the cover from the wiper arm and use a lithium grease such as Liquid Wrench White Lithium Grease. Here is a helpful tutorial on how to lubricate windshield wiper mechanism on a Mercedes-Benz. If playback doesn’t begin shortly, try restarting your device.

What does it mean when your windshield wipers wont turn off?

A failed relay can mean the wipers won’t work at all, or they may continue to work even when turned off. Changing the wiper relay is the easiest approach and it might solve your problem. Wiper relays usually cost less than $20.

Why are my windshield wipers not working on my Mercedes C230?

Assume on/off relay is probably fine because there is some functionality. Hood latch sensor issue ruled out because wipers did not work while driving over 5kmh. By process of elimination I assumed combo switch is faulty. My 2004 mercedes Benz c230 windshield wipers do not work.

Why are my windshield wipers not working on intermittent speed?

Diagnostics: Fuse 46 fine. Wipers do Not work on intermittent, I or II speed. Wipers Do swipe for wash cycle (pushing combo switch in once). Assume on/off relay is probably fine because there is some functionality. Hood latch sensor issue ruled out because wipers did not work while driving over 5kmh.

Possible Issues 1 Disconnected Washer Fluid Line / Hose (See fix below.) 2 Mercedes washer fluid reservoir leak 3 Defective Mercedes Windshield Fluid Pump 4 Burned out fuse

What do you do when your windshield wipers stop working?

Also switched relays L ‘Wiper speed 1 and 2’ and Q ‘Wiper on/off ‘ relay with each other,did not had any impact. Is it the wiper motor?

Where are the washer fluid pumps on a Mercedes?

Click to expand… The pump are on the bottom of the washer fluid reservoir. The easiest way to access it is to lift the car, then remove the wheel and the plastic underbody panel between the bumper and tire (it’s called the “fender liner extension”). You’ll see the pumps and the hoses there.

Why does my rain sensor Wiper not stop?

The windscreen was recently replaced by Autoglass due to stone crack. Even though the rain sensor has been connected up (and checked by Autoglass) the wipers run continually when put onto the intermittent (rain sensor) setting – even when dry! I have cleaned the windscreen but no joy.

Why are my windshield wipers moving so slow?

This problem is common and is typically caused by defective Light and Rain Sensor for Automatic Headlights and Windshield Wipers. If this sensor is defective, the wipers may move too fast or slow for no reason. The solution to this problem would be to replace the rain sensor.

How can I tell if my windshield wipers are working?

Set your multimeter to measure DC Voltage. Unplug the power cable from the windshield wiper motor and check for power. Make sure you are pressing the windshield wiper switch to activate the wipers, or you will never get any reading. Step 3: If power is going to the windshield wiper motor you should get a reading between 11 and 14 volts.

Why are the spindles on my windshield not working?

The spindles are what the wiper arms are fixed to. They work hard and can bind as they get older. The binding can cause the link rods to pop off. Running the wipers on a dry windshield can cause the links to jump off, but the real problem is as you know a worn out link rod socket bushing.

Why is my windshield wiper not working on my car?

Replace the windshield wiper motor right away. The windshield wiper fuse is burnt out. When the windshield wiper motor is overloaded, the associated fuse burns out. The fuse is designed to be a weak spot in the windshield wiper circuit.

What are the problems with the Mercedes wipers?

Here is a list of possible issues: 1 Mercedes Wipers Not Working 2 Windshield Wiper Switch Stopped Working 3 Mercedes Windshield Wiper Stays Running / Won’t Stop 4 Mercedes Benz windshield wipers not working 5 Mercedes windshield wiper problem 6 Mercedes E, S, C Class Wipers quit moving 7 Mercedes Wipers stuck on top More

How are the wipers attached to the windshield?

The wiper assembly is like a chassis for the wiper system, it’s bolted to the bulk head just below the windshield. The motor, wiper drive mechanism and wiper arms are all attached to it. When activated a wiper motor rotates continuously and more sophisticated motors rotate left to right.

Where are the spare fuses in a Mercedes W320?

Spare – Spare fuses located in 2nd row (observer correct amperage)- Additional fuses are located underneath the rear seat bench on the right, and the nextr to the light switch in the cocpit- Fuse extractor in car tool kit Fuse box under the seat, near the battery (210 545 05 00): Fuse Ampere rating [A]

What should I do if my windshield wipers are not working?

Replace torn wiper blades immediately so your visibility isn’t compromised. The windshield wipers have ice or snow on them. Windshield wipers are able to remove small amounts of snow from your windshield, but heavy, wet snow needs to be cleared by a snow brush before operating your wipers.

Where is the fuse on a Mercedes W211?

It is in the front passenger’s footwell. It is behind the trim panel on the left side of the trunk. It is near the battery under the trunk floor.

Where are the fuses on a Mercedes Benz E class?

Cigar lighter (power outlet) fuses in the Mercedes-Benz E-Class are the fuses #54a, 54b (cigar lighters) in the Engine Compartment Fuse Box, and fuse #13 (Interior socket) in the Luggage Compartment Fuse Box. The fuse box is located on the driver’s side of the instrument panel, behind the cover.

What does it mean when your turn signal is not working on Mercedes?

In newer Mercedes models, you will get a warning on instrument cluster stating “Turn Signal Left / Right / Front / Rear / Side Malfunction”. Depending on the Mercedes model and problem a warning may or may not show on the dashboard.

Why do my wipers not work when I turn them on?

Your wipers will work on a constant speed when turned on. T he automatic wiper function will not work. Therefore if you set the wipers in one setting, they will stay at a constant speed. It will work like the old school wipers used too. This may disable other features in your car.

What is the fault code on a Mercedes?

You press the gas pedal, and the engine RPMs go up to 4000 or even higher and you are limited to a max speed of about 30 MPH. The check engine light (CEL) comes on. You scan the car using an OBD-II code reader, and you get fault codes such as P0715, P0720, P0700.

Where are the fuses on a Mercedes Benz W164?

Fuse locations on Mercedes-Benz M-Class W164 2006-2011. Main fuse box and relay box is located in the engine compartment. Rear, passenger side in the trunk. Inside the cabin. Passenger side of dash. Prefuse box in the engine compartment. Near the hood hinge, passenger side. Prefuse box by the battery.

Where is the fuse box on a Mercedes Benz W463?

Click here to download the fuse box chart for Mercedes-Benz G-Class W463 in pdf format. Interior fuse box is located on the side of dash. You will find the fuse box if you look at the driver’s (left) side of dash. A plastic cover can easily be removed. Use a Dash Trim Removal Tool to avoid damaging the dashboard.

Why does my Mercedes windshield wiper stop working?

The goal of this article is to address Mercedes-Benz related windshield wiper problems that you may face. Here is a list of possible issues: I- Windshield wiper motor runs, but the arms don’t move. The gear teeth on the shaft of the wiper motor may wear out and cause the wipers to stop moving. Other possibilities that can cause these symptoms are:

Where is the fuse for the windshield wiper motor?

They are located on the side of the dashboard, engine bay, rear seat or even in the trunk. Find the fuse chart for your car and locate the corresponding fuse for the windshield wiper motor. Make sure the fuse is not burned out.

What should I do if my windshield wiper arms are broken?

Windshield wiper arms or linkage broken. The bolt that holds the wiper arms in place is loose. Make sure that the link between the wipers and the wiper motor is not broken. Next, try tightening the bolt that holds the wiper arm in place.

Where are the windshield wipers on a Mercedes E320?

It is located in the driver’s side front fuse box. Why have the windshield wipers, turn signals and horn all stopped working together on a Mercedes E320? There seems to be a problem in the controller area network or the front signal acquisition module.

Why is my turn signal not working on my Mercedes CLK?

Blown turn signal fuse or turn signal fuse keep on blowing. Short in the wires that provide 12 volts to the turn signal. You will need to locate the short and repair it. Check the wiring inside the headlight or tail light as the insulation of the wires may melt over time causing a short. We have seen this happen on several E and CLK class models.

What kind of wiper blades do I need for my Mercedes C class?

Replace your Mercedes-Benz C Class wiper blades and Save 5% when you buy 2 wiper blades and 10% when you buy 3 or more. Select your model and choose from a great selection of quality wipers at discounted prices including Michelin RainForce™conventional windscreen wipers and Bosch Aerotwin flat wiper blades for the front screen.

What should I do if my windshield wiper wont move?

Typical symptoms are: -a slow wiper movement as the wiper moves on the windshield. You should lubricate the wiper mechanism at the center (bottom) of the windscreen. Remove the cover from the wiper arm and use a lithium grease such as Liquid Wrench White Lithium Grease.

How to fix intermittent wiper and turn signal problems?

Disengage the plastic snap clips and separate the two halves of the steering column cover. Multifunction switch levers control headlights, flashers, wipers and intermittent windshield washers. The MFS is usually held in place by hex-head or Torx screws. Remove them, pull out the switch and disconnect the electrical connector.

What are the most common intermittent wiper failures?

The two most common failures are: 1 A broken turn signal “canceling” mechanism that won’t shut off the “blinkers” after a turn, 2 A partial or complete loss of intermittent wiper control. More …

What to do if your Mercedes W123 is bouncing?

Engine having a hard time shutting off? Make sure to check and or replace your injector pump shut off valve. Overload protection relays are located in different places on different chassis, so check for the location of yours and follow these instructions. Car bouncing down the road?

How do you fix a blown fuse on a Mercedes Benz?

Locate your fuse boxes, and become current with fuse sizes as well as color codes. Conduct fuse testing to find blown fuses. Gain the capacity to replace your fuses, and the potential to insulate yourself from shocking repair bills. This article will help you understand the fuses in your Mercedes-Benz C-Class w204.

Where are the fuses on a Mercedes Benz W204?

Testing fuses in place with a multimeter. Use the Mercedes fuse allocation chart to locate a specific fuse and amperage. For instance, the reading lamps are on fuse #17, rated at 30 amps and located in the under hood box. Figure 6. W204 fuse allocation chart (page 1). Figure 7. W204 fuse allocation chart (page 2). Figure 8.

Where do the wipers go in a car?

Rather than pull over and wash the windshield off, let the wipers do this job. To do this, washers and wipers use a number of parts. The wipers use a motor and worm gear inside the wiper motor, which usually sits inside the hood, and these power the blades of the wipers so they move across the windshield at the right speed.

Where are the fuse boxes on a Mercedes Benz?

Location of fuse boxes, fuse diagrams, assignment of the electrical fuses and relays in Mercedes-Benz vehicles. Fuse box diagram (location and assignment of electrical fuses and relays) for Mercedes-Benz A-Class (A140, A160, A170, A190, A210) 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004.

How to fuse a Mercedes Benz C Class W204?

To open: pull out cover (1) slightly at the bottom in the direction of the arrow (3). Do not use a pointed object such as a screwdriver to open the cover in the dashboard. You could damage the dashboard or the cover. Pull cover (1) outwards in the direction of the arrow (2) and remove it. To close: clip in cover (1) on the front of the dashboard.

Why does my wiper keep blowing the fuse?

It can be frustrating when your vehicle keeps blowing your windshield wiper and washer fuses. Several reasons exist for a blown fuse for windshield wipers and washers. The windshield wiper or washer motor could be drawing too much current. To see if this is the problem, disconnect the wiper motor for a little while.

Why does my windshield wiper keep burning out?

When the windshield wiper motor is overloaded, the associated fuse burns out. The fuse is designed to be a weak spot in the windshield wiper circuit. That way, if the motor is overloaded for any reason, the fuse will burn out first, instead of the more expensive wiper motor.

What kind of fuses are in a 2013 ML350?

Electrical components such as lights, heated seats and radios all have fuses in your 2013 Mercedes-Benz ML350 3.5L V6. This free video shows you how to replace a blown interior fuse on a 2013 Mercedes-Benz ML350 3.5L V6 About Us Maintenance Parts & Tools Contact English SpanishFrench Search Home Mercedes-Benz GL450 2013

How often should you change the wiper blades on a Mercedes R350?

We recommend changing the wiper blades on your R350 at least once a year even if you don’t use your wipers much – the sun wears out your wiper blades more than using them to wipe water. Another trick to enhance the longevity of your R350’s wiper blades is to scrape off the ice and snow from the windshield before using your wipers.

Where is the Mercedes C class wiper relay location?

04 C230 Sedan Windshield Wipers Not Working At All Mbworld Org Forums Windshield Wiper Relay Location Fo230k Mercedes Benz Forum Mercedes W211 Windshield Wiper Fuse Replacement Location Youtube 04 C230 Sedan Windshield Wipers Not Working At All Mbworld Org Forums Solved S430 Turn Signal Relay Location Fixya

Why are my wipers not working on my 2003 C240?

2003 C240. went to turn on the wipers today and nothing. I have done a little troubleshooting so far and have done some research on the forum. I have not found anything else not working.

What are the symptoms of a bad intermittent wiper relay?

1. The windshield wiper blades have one speed 2. The windshield wiper blades don’t work 3. Wiper blades operate at speeds different than you selected 4. Humming noise when the wipers are on

Why are my wipers not working in the snow?

Turning on the wipers to clear heavy snow will cause excess pressure on the link arm bushings. You’ll find when link rods jump off once, they’ll keep jumping off.

1. The windshield wiper blades have one speed 2. The windshield wiper blades don’t work 3. Wiper blades operate at speeds different than you selected 4. Humming noise when the wipers are on

What to do if your windshield wiper stops working?

I have a 1999, E320 that all of a sudden the windshield wiper and turn signal stopped working! Any ideas? Check fuses. After that, are you handy with a voltmeter?

What happens when you turn the wiper switch backwards?

periodically, when engaging the wipers by turning the switch backwards, it will operate normally, or almost, with one to two swipes before shutting down. Some times, however, it will continue for many swipes and may stop in random positions.

Where are the turn signals on a Mercedes E320?

Case details: The turn signals also respond randomly when engaged. The combination relay, which controls both turn signals and windshield wipers, appears to be faulty and needs to be replaced. It is located in the driver’s side front fuse box. Why have the windshield wipers, turn signals and horn all stopped working together on a Mercedes E320?

Why are the wipers on my C320 wagon not turning off?

I have a 2002 C320 Wagon and the wipers won’t turn off. Intermediate, normal and fast settings work normally, but back in the off position the wipers continue to operate as if in normal continuous mode. Wiper fuse is ok. Swapped the relays around and problem persists.

I have a 1999, E320 that all of a sudden the windshield wiper and turn signal stopped working! Any ideas? Check fuses. After that, are you handy with a voltmeter?

What’s the price of a 2008 Mercedes gl320?

A favorite of ours in this category is the Mercedes GL, so when a diesel V-6 was added to the lineup with the 2008 models, we decided to see how it would work in the U.S. The GL320 CDI, as the diesel is designated, was the least expensive model in the GL line, with a base price of $53,775 when it was delivered in August 2007.

What kind of system does the Mercedes gl320 CDI have?

As are most modern high-end vehicles, the GL320 CDI was equipped with a host of electronic conveniences, many of which could serve as challenging intelligence tests. Prominent among these was the GL’s COMAND system, which is Mercedes’ first-generation version of a combined navigation system and LCD-based electronic controller.

Where are the fuses located on an e320?

You can also see a list of all the fuses, their designation and layout. The fuse boxes shown below are apply to 1996 1997 1998 1999 2000 2001 2002, models E320 E420 E430 E55 AMG. The main fuse box is located on the left side in the engine compartment near the windshield. Here is a layout of the fuses in the main fuse box.

Where are the fuses located in the ML320 ml500?

A second fuse box is located in the passenger footwell. This is the auxiliary fuse box. To access the fuses inside you will need to twist the two plastic locks and pull the cover towards the back of the engine. Fuses in the auxiliary panel. Relays located in the fuse and relay box by the passenger foot-well.

What was the start error on the W163 ML 270?

Day 2 : Start error on dashboard first thing in morning and after a few minutes no sign of life, tried two different keys. Walked to train station. Upon returning home that evening same problem, tried to use a booster battery and after a couple of hours of tinkering with battery it started.

What kind of radiator does Mercedes ml270 use?

Click to expand… The box uses a water to oil heat exchanger to cool the box and the last box that was installed in the ML270 the specialist changed it to an air cooled radiator for cooling the box! Click to expand…

What do the warning lights on my Mercedes mean?

Or, if you have RAC Breakdown Cover, call for recovery. This warning light indicates that there’s a problem with the power steering. For electric powered systems, this problem could be as simple to fix as rebooting a computer. Find a safe place to stop and try turning the car off and back on again after 30 seconds.

Why is the rain sensor on my Mercedes not working?

Mercedes have the rain sensor mounted up by the rearview mirror. The sensor can technically fail but as you are already noticing there is something else major going on here. Another issue that this particular car developed was the climate control would randomly stop working. Other times the climate control would operate completely normal.

Why are the lights not working on my Mercedes?

Lights not working – We have seen many Mercedes-Benz where one or a few lights don’t work. It can be that the left or right low beams, fog lights or turn signals may not work. You should always avoid splicing wires to get power for aftermarket HID lights, alarm or connecting a trailer hitch.

What causes a Mercedes signal acquisition module to fail?

Typically this is caused because repair is performed in near the SAM control unit. If the SAM modules are not closed and sealed, properly they will eventually corrode. If a SAM module fails due to corrosion, at first you may notice that electrical problems are intermittent. Excessive current draw – SAM control units don’t fail often.

Why is Wiper not working on 2014 Oly windsheild?

I have 2014 B250.. few days back wiper blads started moving slow. Then sometimes they work sometimes wont. Now the rite side works and the driver sides dosent. Cant figure out the problem. Any help would be highly appreciated. Check wiper system, see attachments. Not open for further replies.

Why are my wipers not working on my C230?

Wipers Do swipe for wash cycle (pushing combo switch in once). Assume on/off relay is probably fine because there is some functionality. Hood latch sensor issue ruled out because wipers did not work while driving over 5kmh. By process of elimination I assumed combo switch is faulty. My 2004 mercedes Benz c230 windshield wipers do not work.

How do you remove a wiper switch from a car?

Two screws hold each the turn signal and wiper switch into their housings, and the electrical connector can be disconnected to remove the switch from the car. Once open, the switch contacts can be cleaned with electrical contact cleaner and sandpaper to allow for proper contact.

Why is the fuse on my windshield wiper not working?

The windshield wiper fuse is burnt out. When the windshield wiper motor is overloaded, the associated fuse burns out. The fuse is designed to be a weak spot in the windshield wiper circuit.

Why does my on / off relay not work?

When to buy new Mercedes windshield wiper blades?

If you find they are leaving behind smears or smudges on the windshield, you need to get a new set. Buy new OEM windshield wiper blades here for your Mercedes. Notes: 12. Description: Set. E class. Cls class. To 2/28/14. To 2/27/14. Sedan/wagon, to 3…

Why do windshield wiper blades wear out so fast?

Windshield wiper blades are components that are going to wear out quicker than a good amount of the other parts built onto your Mercedes. This is because they are exposed to a range of elements and are often used frequently.

Why are the flashers on my Mercedes not working?

I had the same problem with the flashers intermittently not working. I eventually traced it to a dry (i.e. bad) solder joint on one of the legs of the fuse holder for the flasher circuit. This is in the light switch/fuse module in the console next to the steering wheel (accessible when you open the driver’s door).

What are the warning lights on a Mercedes Benz?

The following are warning lights and indicators found in vehicles built by Mercedes Benz. Click a link to learn more about each one. They are roughly ordered by importance, which tends to be by color (red, amber, yellow, orange, green, blue, gray), but there are over 40 of them so be patient!

How to discuss a Mercedes Benz door lock problem?

Start a new thread on your specific issue. Also try using the ‘search community’ at the top of your webpage for other threads on the w202 forum and even the w210 forum. ===>>> Update your user CP info…. Did you find the recommended reading relevant to this discussion?

What does it mean if your Mercedes Sam is not working?

You should eliminate any other possible issues and even get a second opinion before you replace the SAM unit. If you get an error message that no communication with the SAM module exists, it means that the SAM is defective or it is not getting power. Used Mercedes SAM units are affordable and one option if you have an older MB.

How do you remove wiper arm from Mercedes?

Try wiggling the arm to get it off the linkage. If you can’t remove the wiper arm, use a puller. Remove the weather & wind strip. Remove the plastic cover (rain tray/cowl/rain diverter) near the firewall.

What was the fatal flaw of the Mercedes Benz Sprinter?

This article is being written to warn potential buyers of this vehicle of the fatal flaw hidden in each of these vehicles. Prior to 2008, when the United States Government mandated diesel exhaust regulations, the Sprinter, manufactured by Mercedes Benz and sold as a Dodge was a real workhorse.

Why are my shift controls leaking in my Mercedes?

You CAN do this yourself if you have the right information and equipment! High Mileage and age can raise havoc on the shifting patterns of an automatic transmission. Even if the fluid has been changed on a regular basis, they still wear out. Seals harden and leak both internally and externally. Vaccum and cable shift controls leak and fail.

Where are the transmission codes stored in a Mercedes?

Specific codes related to the transmission are stored in the TCU (Transmission Control Unit) and come generic codes such as P0705 are stored in ECU (Engine Control Unit). You don’t need to pay anyone to read the codes; you can retrieve them yourself in a couple of minutes with the right OBD II scanner.

What to do when your Mercedes goes into limp mode?

You may also get a check engine light if your transmission goes into limp mode. When a Mercedes-Benz goes into limp mode, it only operates in second gear and reverse only. When you put it in gear, you may also feel a bang as transmission engages. The first thing you should try is to check the transmission fluid level.

Where is the power wire for the wiper motor?

Connect the white, red or green wire from the wiper motor to the second blade on the wiper switch terminal. This is the power wire connection. Tuck the wiper switch terminal back up into the wiring harness of the dash so it is not hanging down.

How does a windshield wiper motor work on a car?

Windshield Wiper Motor Wiring. The windshield wipers on a vehicle are powered by a switch that connects or disconnects the power to the windshield wiper motor. When the motor wears out and needs to be replaced, connecting the windshield wiper motor wiring to the switch can be confusing.

What happens if there is no power to the wiper?

If there is power, the motor is bad. If there is no power, although the motor could “still” be bad, you first want to trace the circuit back to the power source to figure out where the break is. Once the circuit is fixed, of course if the motor still doesn’t work, it’s condemned and replaced.

Is the 1991 Mercedes 350 SDL Turbo for sale?

1991 MERCEDES BENZ 350 SDL Turbo Diesel Up for sale is this beautiful 1991 Mercedes Benz 350SDL Turbo Diesel model. Original ONE OWNER CAR, Even states ONE OWNER on the clean New Jersey Title. This vehicle has been sold through an Estate Sale since the owner who was very old passed away.

Why are my windshield wipers not working when I turn them on?

The system is powered by an electric motor, which drives the mechanical linkages that make your wipers move across your windshield. If your wipers don’t respond when you turn them on, here’s a simple way to see if you have an electrical problem or a mechanical one: With the car off, try to manually move the wipers back and forth.

How are the parking lights on a Mercedes Benz?

In newer Mercedes-Benz models, like mine above, the parking lights activate in a slightly different way; you must first turn the light switch to “P,” for “parking,” and then you can put on the turn signals to switch on whichever parking lights you want. But this feature still exists, it’s still standard, and, well, does anyone use it?

Is there any way to troubleshoot a Ford wiper motor?

Or you may be having trouble getting your wipers to work at all. Fortunately, the motor unit can be replaced. However, before replacing the motor, you should troubleshoot the problem. There are several simple solutions that can solve most Ford wiper motor problems. Open the fuse panel cover under the steering wheel.

What should I do if my windshield wiper is not working?

Generally speaking, you can reach the motor and transmission by removing the wiper arms, all the screws that hold the cowl beneath the wiper arms and the weather stripping. Once exposed, you should be able to remove the motor from the transmission and check to see if the transmission is binding or if the motor is the culprit.

The windshield wiper fuse is burnt out. When the windshield wiper motor is overloaded, the associated fuse burns out. The fuse is designed to be a weak spot in the windshield wiper circuit.

What to do if your fuse panel is not working?

If those fuses are okay, check the smaller spade-type fuses in the inside fuse box the same way, and try to determine which fuses are dead and which ones do have twelve volts. Do that with the ignition switch in the “run” position. Based on your findings, I will look at the diagram for your engine and see what the dead fuses have in common.

What to do if your windshield wiper Fuse has burned out?

Find the fuse chart for your car and locate the corresponding fuse for the windshield wiper motor. Make sure the fuse is not burned out. Once you remove the fuse, a good one should look like the one in the picture above. If the fuse has burned out, replace it with a new one with the same ampere rating.

What should I do if my wiper is not working?

Open the lid and check for corrosion and damaged connections. Repair as required. If nothing is found, disconnect both the battery cables and leave them off for fifteen minutes. This may reset the system and fix the problem. If after reconnecting the cables the same issue remains, the UPC may have to be replaced.

Why are the wipers on my Renault Modus expression not working?

When the switch fails, the position of the wipers is not sensed and the motor will work only at high speed. The motor will have to be replaced. What could cause the wipers on a Renault Modus Expression to remain on, even with the switch turned to OFF?

How can I Disconnect the horn on my car?

How can I disconnect the horn on my car? To disconnect the horn, locate the fuse for the horn in the fuse box. Remove the fuse. The car will still operate normally without a horn. You can also remove the horn relay. You can disconnect the wires from the horn as well. Any of these methods will disconnect your horn and render it inoperable.

Navigation