Why are my Pontiac Grand Am security lights not turning off?

The theft deterrent is disabling the starting of the vehicle because you have a problem with it. Your vehicle has what’s called ‘Passlock’. There is a sensor inside the ignition cylinder that has an electronic password. And i had read that if it is the ignition then the lights would not turn off.

What does it mean when Trac off light comes on?

I have a 98 Pontiac Grand Prix that trac off light comes on while driving, have taken it to dealer & he can’t figure out the problem. The car will jerk & almost stall, then run normal when trac off light comes on. Cannot turn it off by button. Any help would be appreciated. Thanks 168 people found this helpful.

What causes a Grand Prix ABS light to go off?

Improper tire size, such as two different sizes, will cause the wheels to turn at different speeds and may set a false code when the computer senses this as potential wheel lock-up. Low fluid level in the brake master cylinder will result in shutdown of the ABS and Traction Control system to prevent introduction of air into the brake system.

What to do if your Pontiac Grand Am has a vacuum problem?

If you go to auto zone they will plug the code scanner into your car for free. The code will probably come up as a vacuum problem, and or a 0300 code which is multiple misfires, but don’t sweat the car is probably not misfiring it’s all comeing from the faulty electrical system.

What’s the problem with my Pontiac Grand Am lights?

I ran a check on the system of the car, and I’ve discovered that the EBCM (electronic brake control module) is what’s causing the problem with the lights. The module costs around $600.00 but you might be able to go to a dealer and have the tech reprogram the module.

Where is the anti lock brake relay on a Pontiac Grand Am?

If your car is a 2000 or newer you might find the anti lock brake relay underneath the battery tray along the left frame rail of the car. If you go to auto zone they will plug the code scanner into your car for free.

How to fix a Pontiac Grand Am PassLock sensor?

Best way to fix is to permanently disable/disconnect passlock system. Not fixed, security light comes on solid and goes away in different time intervals while driving, then after a couple of starts it goes in that limp mode where the security light blinks. I continuously have to wait until the light stops blinking….

Why does my 2003 Grand Am Not Start?

My 2003 Grand Am sometimes wont start. I’ve noticed that when it wont start, the security light is flashing. To resolve the problem I have to leave the key in the ignition with it in the “ON” position for 12 minutes to reset the sensor. The sensor light wiull stop flashing when it is reset.

Why is the security light on on my Grand Prix?

You cannot just turn it off unless the problem is fixed. The security light is on because you have a problem with your Passlock theft system. There are temporary fixes, like doing a re-learn of the theft deterrent, but the problem will come back. Most likely, you need a new ignition cylinder. Those are what usually go bad on the Grand Prix cars.

Why is my PassLock not working on my Grand Am?

It turns out that although the most common culprit is a Security module in the ignition switch, there are several other possible causes for this Passlock problem. Anything which causes the apparent resistance in the circuit to change by a significant amount will trigger the security system, and cause the car not to start.

What is the ignition lock part number on a Pontiac Grand Am?

6/7/2011 Finally, the PREFERRED method of doing this modification Through the radio cavity, NO SOLDERING REQUIRED bergerweb.net/PasslockFix Note: 09/24/2010 The ignition lock part number is the same for all these cars: 1999 – 2004 Oldsmobile Alero 1997 – 2003 Chevrolet Malibu 1999 – 2004 Pontiac Grand Am

How can I reset the warning lights on my car?

Loosen the nut that holds the negative terminal to the battery with the pliers. The negative terminal is labeled with a minus sign (-) or is black in color; the positive terminal is red. Touching just the negative or positive terminal will not cause an electric shock, but touching both at the same time will.

Why are there warning lights on my dashboard?

When your vehicle’s computer senses a problem with a prominent piece of equipment such as the transmission or engine, it will send out a code to alert you. This will result in a warning light appearing on your vehicle’s dashboard.

Why does my Pontiac Grand Am Not turn on?

All three lights are on and when you make a hard right or left turn and accelerate at low speed the car seems like the drivetrain is missing, almost like it’s skipping. If anyone has any suggestions please let me know.

How much does a Pontiac Grand Am touch cost?

It sounds like it is a $700-$900cdn touch. I have about 71k on my GA and I have already replaced both the left and right wheel bearing retaining hubs. Recently over the last 2 months these lights have been coming on intermittently, generally when driving in wet weather. Any ideas?

Where to get a service engine for a Pontiac Grand Am?

Go to a parts store like O’Riely or AutoZone and use the code scanner. That should give you a good place to start. You can use the code scanner for free or very low cost. You do NOT need to buy one. This could be anything from a cracked vacuum line to a bad computer.

How do you turn off the security light?

Insert the master key with the black head into the ignition lock cylinder 2. Turn the key to ON but do not start the engine. The SECURITY light will turn on and stay on. 3. Wait 10 minutes or until the SECURITY light to turn off. 4. Turn the key to OFF for 5 seconds. 5. Turn the key to ON but do not start the engine.

Why is the security light on on my car?

The security light on your vehicle serves has two purposes. On some vehicles, it will flash when the ignition is off, and the OEM security is activated. Its other main purpose is to indicate that the security of your vehicle may have been compromised, and the engine has been immobilized…

When does the Toyota Corolla security light go off?

If nothing happens or the engine starts and dies, the security light will be flashing. Wait ten minutes. The flashing light should go off or illuminate without flashing. When it does, turn the ignition off, wait twenty seconds, and then try to start the engine.

Is it normal for the security light to go off when the engine is running?

After the learn procedure is completed and the engine is running, the security light may stay on steady for a few minutes and then go off—this is normal. Depending on the system, replacement of key components will necessitate that a relearn procedure be completed.

What should I do if my PassLock security light goes off?

Why does my car not start when I Turn Off the ignition?

If a fault occurs while driving, the engine may or may not start after turning the ignition off. If a fault occurs when trying to start the vehicle, it probably won’t start.

When does a Pontiac Grand Am out of gas?

(PRWEB) February 21, 2005 — If you own a 2001 Pontiac Grand Am, you’d better hope you’re not stuck somewhere bad when this hits: You go to start your car, and the engine cranks, but it seems like your out of gas, and won’t start.

What do I need to replace my 2002 Grand Am?

It is a 2002 grand am and so far I have had to replace the Catillic (not sure on the spelling) converter, master cylinder, fuel pump, gastic manifold, rack and pinon (spelling), hazard light switch (which still is clicking), and power steering pump. Also I need a new raditor.

How much oil do you put in a Pontiac Grand Am?

The amount of oil you want to put in the engine is 4.8 liters or 5 quarts. That is straight from General Motors. Thank you very much. Not a problem, thank you and have a good night!

What to do if your Grand Am won’t start?

When your Grand Am turns over but won’t start it maybe your anti-theft security system. When the security light blinks, the car won’t start. You must do a simple reset. The procedure in this video is what worked for us. Use of the free information in this video is at your own risk.

How to bypass the PassLock sensor on a 2002 Pontiac Grand Am?

This web page will guide you through the steps necessary to bypass the “Passlock Sensor” on a 2002 Pontiac Grand Am, and keep the “SECURITY” light off forever. The steps necessary are similar on the other models listed above. There are generally only minor differences in how to get the radio out to get to the wires.

Why does my car stall with the security light on?

It should start, and then stall, with the “SECURITY” light flashing. (In rare cases, the car may keep running and the security light will not illuminate, but that only happens if you are very lucky.)

What to do if your PassLock light does not turn on?

Insert the Key into the ignition switch and try to start the car. It should start, and then stall, with the “SECURITY” light flashing. (In rare cases, the car may keep running and the security light will not illuminate, but that only happens if you are very lucky.)

What to do if your PassLock security light flashes?

“After attempting to start the engine, if the “SECURITY” light flashes or stays on, wait ten minutes with the key in ON until the light goes off. Then turn the ignition to OFF before attempting to start the engine again.” This normally works! Unfortunately, a few weeks later, you will probably have to go through the entire routine again.

What kind of security system does GM use?

VATS, Passkey or Passlock – are the core of GM security systems, have a short lifespan and they’re certainly more effective at keeping you from DRIVING your car than keeping someone from STEALING your car! GM Security Systems are killing cars all over North America and the only final solution is to disable and remove them permanently.

Is there a way to bypass GM security system?

Scouts Troop 980 of Utah cheers as their ’92 Olds Toronado is coming back to life. Thanks to the NEWROCKIES Full Bypass Module! How to FULLY bypass VATS Passkey and Passlock Security Systems in GM Cars. Has the dreaded GM Security system just hit you?

How to permanently disable and remove GM security systems?

GM Security Systems are killing cars all over North America and the only final solution is to disable and remove them permanently. This is what NEWROCKIES Inc is all about.

How can I Reset my GM car alarm?

After deactivating it, you can reset the alarm to ensure that your GM vehicle security system is set correctly. Use your GM keyless remote to unlock the doors by pressing the “Unlock” button.

Can a GM security system be moved to another car?

Newrockies inc proudly manufactures its modules with top quality electronic components. No more risks of remaining on the road. Universal. The same module works with over 100 different GM and Isuzu cars – you can even move it on your next car! Trusted.

Is there a way to bypass GM PassLock?

At NEWROCKIES Inc., we’ve designed our PRO Bypass Module with the specific purpose of bypassing faulty GM VATS, Passkey and Passlock security systems IN FULL.

How do you replace a Pontiac Grand Am security light?

Remove the cylinder from the ignition switch and replace with a new cylinder and Passlock housing….after replacement you will need to do a theft re-learn. To know exactly, you’d need a proper scanner to access the body control module and check for theft system codes.

What happens when the security light goes off on a Pontiac?

The security light will stop after 600 seconds. This puts the security system in reset mode. After the light goes off you can then start your car.

What causes a Pontiac Grand Am to lock out of startup?

This is caused by a bad ingnition switch in most cases however if you have a cut key (non factory ingnition key) sometimes it will register it as a bad key..remove the key and try again…however I do believe you only get 3 tries otherwise the car is locked out of startup for 30min to 1hr. 60 people found this helpful.

The amount of oil you want to put in the engine is 4.8 liters or 5 quarts. That is straight from General Motors. Thank you very much. Not a problem, thank you and have a good night!

What to do if your Pontiac Grand Am wont start?

Videos you watch may be added to the TV’s watch history and influence TV recommendations. To avoid this, cancel and sign in to YouTube on your computer. I created this channel to help people with small maintenance and repairs.

What should I do if my Toyota Corolla security light goes off?

The ten-minute procedure involves trying to start the engine. If nothing happens or the engine starts and dies, the security light will be flashing. Wait ten minutes. The flashing light should go off or illuminate without flashing. When it does, turn the ignition off, wait twenty seconds, and then try to start the engine.

Can a GM security bypass kit be installed?

This GM security Bypass kit will work for several GM, Oldsmobile, Chevy, Pontiac or even Buick vehicles on the street today. I was surprised to see how easy it was to install with very little effort.

How to bypass factory theft on a GM vehicle?

This is a really unique security system bypass kit that you can use to override your current factory theft system on your GM vehicle. You can get this kit from New Rockies.com . I came across this site surfing the net when I was having a similar issue on a GM vehicle.

How to bypass vats, Passkey and PassLock security systems in GM?

It can be VATS, Passkey or Passlock anti theft system that is going bad causing your issue. I am going to share a secrete with you on how you can bypass these systems with very little effort. This is a really unique security system bypass kit that you can use to override your current factory theft system on your GM vehicle.

What to do when your Pontiac Grand Am won’t start?

To resolve the problem I have to leave the key in the ignition with it in the “ON” position for 12 minutes to reset the sensor. The sensor light wiull stop flashing when it is reset. Then I turn the key off and then back to start. It works every time but the 12 minute wait is a pain in the ass.

Why does my Car start when my security light is on?

It works every time but the 12 minute wait is a pain in the ass. Security system has been malfunctioning for a few years. When security light is on solid all the time, the car starts every time. That is because the security system is disabled. Only when the security system is enabled, security light off, the car has starting issues.

This GM security Bypass kit will work for several GM, Oldsmobile, Chevy, Pontiac or even Buick vehicles on the street today. I was surprised to see how easy it was to install with very little effort.

How to reset the theft system in a Pontiac Grand Prix?

Enter the vehicle and insert the ignition key into the ignition. Turn the ignition to the “ON” position but do not start the engine. Wait 30 seconds and start the engine. Verify that none of the security lights on the dashboard are flashing or illuminated.

What’s the best way to reset a car alarm?

Step 1: Unlock the car. Sometimes an alarm will deactivate when you try manually locking and unlocking the car. When the vehicle notices that the key has been inserted into the lock, the alarm may shut off. Step 2: Start the car. You may also try turning the car on to reset the alarm. Step 3: Use key to lock and unlock.

What happens if I disable my car alarm?

Disabling a car alarm can be a temporary fix before seeking professional auto assistance. However, keep in mind, car alarms are meant to be anti-theft, and when tampered with, some systems prevent a vehicle from starting as a security measure. Understand the basics of an alarm system. Alarm systems consist of a few components. Control unit.

What to do if your car alarm starts when you turn it on?

Fix an alarm that starts when you turn the car on. You could need a new battery. Disable the alarm by removing the alarm fuse, and then bring the car to the shop. They can check your battery and move on from there if the problem is the alarm system.

How long does it take to turn off a GM security light?

Leave the key in the “ON” position for approximately 11 minutes. The security light will be steady on or flashing for the 11-minute period. Do not proceed to Step 2 until the security light turns off or stops flashing. 2. Turn the ignition switch to the “OFF” position for 30 seconds. 3.

How to override the security system on a 1998 Grand?

The indicator light on the dashboard should remain lit for three seconds and then shut off, indicating that the system has been overridden. Turn the key back to the “Off” position and remove the key. The LED indicator light should begin to blink, indicating that the SecuriLock system has been reset.

How to reset the change oil light on a 1998 Grand?

The LED indicator light should begin to blink, indicating that the SecuriLock system has been reset. Emily Retherford has been a full-time writer since 2009. She specializes in travel, parenting, fashion and beauty with work appearing on various online publications. How to Reset the Change Oil Light on a …

What are the names of the Pontiac warning lights?

Click a link to learn more about each one. They are roughly ordered by importance, which tends to be by color (red, amber, yellow, orange, green, blue). There are over 40 of them, so search carefully! Models examined include G3, G5, G6, G8, Grand Prix, Solstice, Torrent, and Vibe.

How to fix Chevy Impala with security light on?

Chevy Impala No start? Security light on? FREE FIX with your finger! – YouTube Chevy Impala No start? Security light on? FREE FIX with your finger! If playback doesn’t begin shortly, try restarting your device. Videos you watch may be added to the TV’s watch history and influence TV recommendations.

Navigation