Where to pull fuse on Jeep Grand Cherokee?
The fuse you want to pull is number 25 in box closest to fire wall. Pull fuse then start engine and move car forward and back a little ways.. Before turning engine off put fuse back in and turn engine off.
How to fix 4 wheel drive Jeep Grand Cherokee?
The “Service 4wheel Drive System” come on the dash steady. Drive around for abit then put fuse back in with engine running. Shut off engine then restart. My problem was fixed and it goes in and out of 4low now. 33 people found this helpful. I got the fix for this problem from another site.
Is the drive shaft on a Jeep Grand Cherokee bad?
I test drove a 2006 dodge charger brand new and the drive shaft was bad it had the same vibration. The guys at the shop could not believe it. I live in Canada but have the same problem with a 2005 Grand Cherokee. Have had drive shaft replaced, wheels balances, tranny rebuilt and various other tests.
Where is the negative terminal on a Jeep Grand Cherokee?
The module is located under the rear passenger bench seat (driver side) and it is very very easy to pull the old module and install the new one. It is “plug & play” wiring, but you do need to disconnect the negative terminal from the battery before you do it. Will need some basic tools (18mm socket) to lift the backseat off to access the module.
Is there a way to disable the alarm on a Jeep Cherokee?
Although Jeep doesn’t provide a method for permanently disabling the alarm on its Grand Cherokee, there are a variety of methods that can temporarily disable it or simply shut it off. When the alarm goes off, lights flash and a loud sound is emitted for three minutes.
Why do I need to disable Auto start on my Jeep?
Auto Start-Stop is ‘designed’ to save us some gas money, it might save us a few dollars per year, but that’s actually not the goal of the manufacturer. This guide will show you how to disable this annoying feature on Jeep Cherokee, Grand Cherokee and Wrangler & Compass.
How can I tell if my Jeep Grand Cherokee is shifting?
Turn ignition key ON and OFF three times, finally leaving the key in the ON position. Leave the Overdrive Off Switch in the normal overdrive (ON) position. Immediately begin counting the number of flashes displayed by the Overdrive Off Switch indicator lamp. There will be two sets of flashes, separated by a pause.
What’s the Flash code on my Jeep Grand Cherokee?
Code 26 – Governor Pressure Sensor Offset Drift Code 55 – End of Message You may or may not be skilled enough to actually fix the problems indicated by the flash codes yourself, but you’re better-armed with an understanding of where the issues lay as you seek help from a mechanic.
Who are the members of the Jeep Commander Forum?
New member introduction. My second Commander! My backup camera SUCKS! My second Commander! Service Tire Press System?
How to service a Jeep Grand Cherokee 4 wheel drive?
The actuator in front diff gets corroded from not being put in 4low enough so it stays stuck in. Also shortly after the N23 recall was done. Take the #25 fuse (e-diff) out in fuse box under the hood closest to the firewall. The “Service 4wheel Drive System” come on the dash steady. Drive around for abit then put fuse back in with engine running.
How much does a Jeep Commander General cost?
Our technicians tell us a software update for the FDCM is available to correct this concern. The average cost for a Jeep Commander General Diagnosis is between $88 -$111. Learn More have abs warning light , esp warning light and service 4 wheel drive sys indicator . have appointment to check it .
Where is the fuse panel on a Jeep Commander?
The fuse panel is located under the instrument panel just to the left of the steering column near the brake pedal (behind the cover near the OBD). Mem. Sw, Courtesy Lamp (B+) Final Drive Control Module (FDCM), Heater Ventilation, Air Conditioning (HVAC), Switch Bank.
When did the Jeep Commander XK come out?
The mid-size SUV Jeep Commander (XK) was produced from 2006 to 2010. In this article, you will find fuse box diagrams of Jeep Commander 2006, 2007, 2008, 2009 and 2010, get information about the location of the fuse panels inside the car, and learn about the assignment of each fuse (fuse layout) and relay.
Is there a problem with my 4 wheel drive Jeep?
Dealer diagnosed a problem as the transfer case shift motor. He said Jeep must be having a problem with them because replacements were on national back order (might take a month or more to get one). He said that I can keep driving it without any harm, and it shifts in and out of 4 wheel low just fine.
Why does my Jeep have a service 4WD light?
The service manager called later in the day and mentioned they pulled a DTC from the DTCM that was isolated as being a faulty code generated from the ELSD due to faulty programming from Chrysler. Seems I’ve read several other people were told the same thing, only to find out that the “flash” repair process isn’t the fix for everyone.