Where to find trouble code on Toyota Sienna?
If a trouble code is displayed during the DTC check in the check mode, check the circuit for the code listed in the table below. For details of each code, refer to the “See page” column in the DTC chart. HINT: Performing a SYSTEM CHECK enables the system, which consists of the multiple actuators, to be operated without removing any parts.
What does the VSC light mean on a Toyota Sienna?
What does it mean when Toyota sienna VSC light comes on? The Toyota Sienna VSC light comes on when there is a fault with the VSC system. In some cases, this light may be accompanied with an ABS light, Check Engine Light or Traction Control Light.
When does a Toyota engine have a trouble code?
This trouble code is usually triggered when the O2 sensor in position bank 1, sensor 1 is bad or has faulty wiring. Replacing the sensor will almost always get rid of the code.
How to troubleshoot a Toyota Sienna with SST?
SST RECOMMENDED TOOLS EQUIPMENT HINT: Torx is registered trademark of Textron Inc. SSM How to proceed with troubleshooting HINT: This is the repair procedure for vehicle pull. Problem symptoms table FRONT SUSPENSION SYSTEM REAR SUSPENSION SYSTEM
Why does the Check Engine light turn on on a Sienna?
The check engine light turns on when the Sienna’s internal computer identifies an error code, signaling an issue somewhere within the Sienna’s mechanical system. A code can be triggered a number of things, ranging from a gas cap that hasn’t been tightened properly to something more severe, such as major engine distress.
When does the Check Engine light come on in a Toyota Sienna?
At some point, odds are the check engine light in your Toyota Sienna will come on. The check engine light turns on when the Sienna’s internal computer identifies an error code, signaling an issue somewhere within the Sienna’s mechanical system.
What are the most common problems with the Toyota Sienna?
Here are five of the most common problems with the Toyota Sienna. On RepairPal, the most commonly reported problem involved the Toyota Sienna’s motorized sliding door. This problem was reported four times as often as the next most common problem. It was also reported more often than every other problem combined.
What causes check engine light to come on on Toyota Sienna?
Often the leak covered the engine and undercarriage of the vehicle with oil. A few owners mentioned problems with the Toyota Sienna’s evaporative emission system. Several reviewers had the check engine light come on when there was a problem with the system. This usually happened because a canister needed to be replaced.
How to check for fuel leak in Toyota Sienna?
1. INSPECT FOR FUEL PUMP OPERATION AND FUEL LEAK (a) Check fuel pump operation. (1) Connect the intelligent tester to the DLC3. (2) Turn the engine switch on (IG) and push the intelligent tester main switch on. NOTICE: Do not start the engine. (3) Select the following menu it
What do you need to know about Toyota Sienna?
HINT: Performing a SYSTEM CHECK enables the system, which consists of the multiple actuators, to be operated without removing any parts. In addition, it can show whether or not any DTCs are set, a DESCRIPTION The Variable Valve Timing (VVT) system includes the ECM, Oil Control Valve (OCV) and VVT controller.
Where is the OBD plug on a Toyota Sienna?
OBD connector location for Toyota Sienna (1997 – 2004) You will find below several pictures which will help you find your OBD connector in your car. The OBD port is located under the steering wheel at the bottom of the pedals. Go to the OBD2. scanner for TOYOTA. Here is the OBD2 plug on the right.
Where can I find the Toyota OBD2 code?
Common Toyota OBD2 Codes (also see Full List of Toyota OBD2 Codes) P0100 Mass Air Flow Circuit. P0116 Engine Coolant Temperature Range/Perform P0120 Throttle Pedal Sensor Switch “A” Circuit P0121 Throttle Pedal Sensor Switch “A” Circuit P0125 Insufficient Coolant Temperature for Clo
What is the trouble code for a Toyota OBD2?
Toyota Generic Trouble Codes. 1 Common Toyota OBD2 Codes (also see Full List of Toyota OBD2 Codes) 2 P0100. Mass Air Flow Circuit. 3 P0101. Mass Air Flow Circuit Range/Performance. 4 P0105. Manifold Absolute Pressure Circuit. 5 P0106. MAP/BARO Circuit Range/Performance.