Where to find diagnostic code for Acura check engine light?
1. Connect scan tool to the 16-pin data link connector (DLC) located underneath the glove compartment. The connector has a removable cover. 2. Turn the ignition on. 3. Follow scan tool manufacturer’s operating instructions to access the Diagnostic Trouble Codes (DTC’s).
What are the problems with the Acura transmission?
Typical problems include flaring, slipping, or no shifting to third gear at all. Check engine light (CEL / MIL) and gear D5 may also be flashing. To fix this problem, you will need to overhaul the transmission and replace the 3rd gear clutch. A defective valve body can also cause similar symptoms.
When does the Check Engine light come on?
In every car’s life, there comes a time when the dreaded “check engine” light appears. Not to fear. There are many resources you can use to check and diagnose these DTCs (diagnostic trouble codes). For 1992-1995 (OBD1) vehicles you can check these yourself by using the method shown in the picture below.
Where is the DTC code on an Acura?
1. Connect SCS service connector special tool No. 07PAZ-0010100, or equivalent, to service check connector located under the passenger’s side of dash. 2. Turn the ignition on. 3. MIL will indicate DTC’s by outputting a number of flashes. Remember, these are manufacturer specific codes only.
What are the benefits of owning an Acura?
Take advantage of time saving services and treat yourself to exclusive offers. When you add a vehicle, you gain quick access to information and services on the site, including tools that make managing maintenance and service records a breeze. Plus you’ll receive service offers and exclusive benefits all courtesy of the Acura Owners site.
Why does my Acura check engine light flash five times?
Acura check engine light may flash five times when you turn the key to position II but don’t start the car. This happened when the fault codes were cleared with an OBD2 scanner or if the battery was disconnected. It means that the emission systems are not checked by the ECU self-test, also known as the emission readiness test.
What does it mean when your check engine light is blinking?
Check Engine Light Flashing. If your Acura check engine light is blinking it usually means there is an engine misfire. Fuel is not getting burned in the cylinder. In such cases, the engine will also shake noticeably. Do not drive an Acura for extended time if the check engine light is flashing.
Do you have to have a radio code on an Acura?
Serving the industry since 1998. Many Acura radios are equipped with a special anti-theft radio code. This code is not required, unless the radio is removed from the vehicle, or the vehicles battery is disconnected. You should always have a copy of your radio code in a safe place, not in the vehicle!
Where is the color code on a Honda?
For correct identification, please refer to the colour code listings on this site. KEY: Honda Paint Color Codes are located at position 8. Lucite® – Acrylic Lacquer is recommended for SPOT REPAIR, panel repair and overall refinishing of all original automotive finishes.
Where is the Check Engine Light code on a Honda?
You may also retrieve Honda check engine light codes using the Malfunction Indicator Lamp (MIL), by counting the flashes as follows: 1. Connect SCS service connector special tool No. 07PAZ-0010100, or equivalent, to service check connector located under the passenger’s side of dash. 2. Turn the ignition on.
Why does my Acura check engine light keep coming on?
When your Acura check engine light remains on, the problem could be something as simple a loose gas cap. It can also be an indication of a serious engine issue, a problem with the emission system or in some cases even an indication of a problem with the automatic transmission.
What is the OBD code for an Acura check engine?
P1201Cylinder 1 Misfire – Compare possible causes/symptoms for this Acura check engine light code to the Generic OBD II code P0301 P1202Cylinder 2 Misfire – Compare possible causes/symptoms for this Acura check engine light code to the Generic OBD II code P0302
Typical problems include flaring, slipping, or no shifting to third gear at all. Check engine light (CEL / MIL) and gear D5 may also be flashing. To fix this problem, you will need to overhaul the transmission and replace the 3rd gear clutch. A defective valve body can also cause similar symptoms.
1. Connect SCS service connector special tool No. 07PAZ-0010100, or equivalent, to service check connector located under the passenger’s side of dash. 2. Turn the ignition on. 3. MIL will indicate DTC’s by outputting a number of flashes. Remember, these are manufacturer specific codes only.