Where is the fluid leaking from clutch cable?
There is a rubber boot that covers where the cable connects and swivels. It’s leaking there under the boot and running down the cable. It doesn’t look like that connection can be tightened in any way. Anyone else seen this problem or know what to do about it?
Why is oil running out of clutch cable?
If there is oil running out of it, it’s because someone used to much of the wrong lube on the cable. The connection you refer to is the cable adjuster. I would remove the whole cable and flush the oil out of it with “Berakclean” and re-lube it with Dri-Slid or one of the other DRY cable lubes. One more thing to check is the trans vent tube.
Where does the clutch cable go on a Harley Davidson?
I noticed a couple of days ago that there is fluid leaking from my clutch cable about midway between the clutch handle and where it goes under the bottom of the bike. There is a rubber boot that covers where the cable connects and swivels. It’s leaking there under the boot and running down the cable.
If there is oil running out of it, it’s because someone used to much of the wrong lube on the cable. The connection you refer to is the cable adjuster. I would remove the whole cable and flush the oil out of it with “Berakclean” and re-lube it with Dri-Slid or one of the other DRY cable lubes. One more thing to check is the trans vent tube.
There is a rubber boot that covers where the cable connects and swivels. It’s leaking there under the boot and running down the cable. It doesn’t look like that connection can be tightened in any way. Anyone else seen this problem or know what to do about it?
I noticed a couple of days ago that there is fluid leaking from my clutch cable about midway between the clutch handle and where it goes under the bottom of the bike. There is a rubber boot that covers where the cable connects and swivels. It’s leaking there under the boot and running down the cable.
What happens when a clutch slave cylinder leaks?
Leaks on the floor or engine bay. If the clutch slave cylinder develops any leaks, fluid will drip down and leave traces on the floor or in the engine bay. Depending on the severity of the leak, a leaking slave cylinder will usually also have a noticeable, adverse effects on the pedal feel as well.
How can I tell if my car has a cable adjuster?
The connection you refer to is the cable adjuster. I would remove the whole cable and flush the oil out of it with “Berakclean” and re-lube it with Dri-Slid or one of the other DRY cable lubes. One more thing to check is the trans vent tube.
The connection you refer to is the cable adjuster. I would remove the whole cable and flush the oil out of it with “Berakclean” and re-lube it with Dri-Slid or one of the other DRY cable lubes. One more thing to check is the trans vent tube.
What causes a clutch cable to fail early?
However, it is common to see clutch cables fail early due to overusing the clutch. Many operators of vehicles use the clutch every time the shifter is moved. Often, other operators operate clutches with a float method, which eliminates the use of depressing down on a clutch pedal.
How does a cable clutch shifting system work?
The cable clutch shifting system works in essentially the same way as any other clutch, but it has fewer pivot points. In fact, it’s wonderfully simple. It’s lightweight, and it’s the most common type of linkage in most cars that are on the market today.
Where is the fuse panel on 1989flhtcu?
Found them they were covered in dust after removing the dust from the top I could see the map to the fuses. It’s not on the left side unless you have to take apart one of the 2 boxes located on the left side. Where is the fuse panel on 1989FLHTCU ?
Can a trike pilot keep up with riders?
A good trike pilot can keep up with most of the riders out there. I was going down the Pig Trail (locally famous for it’s curves) to camp at a rally, and I kept having to brake in the curves for a pair of sportbikes ahead of me. They’d pull away on the straights, I would catch up on the twisties.
Can a jiffy stand cause a motorcycle clutch to leak?
Protip 1: If your bike is sitting on a jiffy stand, it is possible (though not probable) that, due to the angle, some of the primary fluid could leak out if it is overfilled. It is always a good idea to place a rag underneath your motorcycle to guard against gunking up any surfaces that you don’t want to gunk up.
Why does my Clutch not disengage on my Harley?
Harley Clutch seems to not completely disengage. Any suggestions? If the steel plates are blue, they have been over heated and are no good. Would suggest replacing all steel and fiber plates. It would be more helpful if you told us your make and model. There are a few things that can cause a m/c to do what you described.
How do you disconnect the clutch from the clutch?
You may be able to disconnect this by pushing the clutch operating lever away from the nipple with your fingers, then pulling the nipple out of the lever with pliers. But if the cable is too tight, you must slacken the cable tension. Look back along the cable and find the cable adjuster.
What should I do if my clutch cable is not renewing?
If there is still no improvement, you will have to remove the clutch cable and try lubricating it. Use modelling clay to make a funnel around the outer cable. If the cable is undamaged, it may simply require lubricating. You can sometimes oil the cable while it is in the car, but to do a really good job you need to remove the cable first.