Where are the nuts on a MerCruiser starter?
Remove the lock nuts from the bolts holding the starter in position. Most Mercruiser starters have bolts that will run from the bottom to the top, rather than from side to side like on a car starter. Once the nuts are off, reach underneath and pull the bolts out.
Can a marine engine starter be removed from a MerCruiser?
Auto starters will work for a short while with a marine engine, but a car’s starter is not meant to take the same kind of abuse a marine starter is. You can remove a Mercruiser starter with minimum effort and bring it to a shop for a rebuild, and avoid the cost of a new one. Disconnect the negative terminal of the battery.
Which is the best way to remove mercury?
A comparison of these more up-to-date mercury removal process solutions is made in three case studies, and the individual plant drivers leading to the requirement to remove mercury are discussed. Why remove mercury?
Why do they remove mercury from natural gas?
A well-known reason to remove mercury in a natural gas processing plant is to protect brazed aluminium heat exchangers and the cold box in nitrogen rejection units, to prevent the compromising of these valuable pieces of equipment.
What to use to remove starter from MerCruiser?
Grind, file or hammer the tool to fit the machine; use that ball peen carefully on the casting unless you really want to break it. A replacement 3/8″ bolt with a 1/2″ hex head may be difficult to find. I’d suggest going with an Allen head bolt when you do get it off. A replacement 3/8″ bolt with a 1/2″ hex head may be difficult to find.
Remove the lock nuts from the bolts holding the starter in position. Most Mercruiser starters have bolts that will run from the bottom to the top, rather than from side to side like on a car starter. Once the nuts are off, reach underneath and pull the bolts out.
What’s the best way to replace a starter?
Here is the trick to removing the starter. The dealer and most mechanics remove the exhaust, but we have a better solution. You can remove the engine mount on the passenger side wich will give you room to remove the old starter and install the new one.
Where to remove the starter from a Mercedes medic?
Remove the 16 mm bolt on top of the engine mount. It is located under the exhaust so it will be difficult to see the top of the bolt, but having the right wrench turns this task from almost impossible to easy. On the bottom of the engine mount, there should be a 13 bolt that you will need to remove as well.
How do you remove a starter from a MerCruiser?
Tear off three small strips of electrical tape. Use the tape and a permanent marker to label the wires that attach to your starter. There is the positive wire (that comes from the starter coil), the ground (which will go from the starter to the engine block), and you may have a third accessory wire.
How do you replace a starter in a car?
Place the wires that are bolted to the bottom bolt to the side. Pull the starter down from the engine compartment. Replace with the new starter. Start both bolts by hand. Ensure the negative lead wire is pushed onto the bottom bolt before tightening. Secure both bolts with a socket wrench. Unscrew the stud on the top with a socket wrench.
Remove the 16 mm bolt on top of the engine mount. It is located under the exhaust so it will be difficult to see the top of the bolt, but having the right wrench turns this task from almost impossible to easy. On the bottom of the engine mount, there should be a 13 bolt that you will need to remove as well.
Where is the starter mounting bolt on a MerCruiser?
Problem: Starter mounting bolt is broken off with threaded section left in motor block. Being a boat motor, access is very, very limited to the point where reaching down along the motor and feeling is the only access to the rear of the motor block. And that is just where the starter and the mounting bolt is located.
Why is my starter motor bolt breaking off?
Most internet comments and solutions indicate that the only way to get the broken section out of the motor is to pull the motor and then drill and extract. Comments: Note that the reason for the bolt breaking off is not really known. After the boat had set up for several weeks, I tried to start it.
What’s the best way to remove a starter bolt?
The most common recommendation is to simply drill out and use an “easy out” to then twist out the bolt. There is a lot of caution about drilling the hole in the center and taking care not to break off the strong but shatterable easy out. Once the easy-out is broken, getting it out is nearly impossible.
How big is the hole for the starter bolt?
There was the flat mounting surface for the starter on the motor block. Then about 1/4in long smooth-bore hole for the starter bolt dowel section, and then the beginning of the threads for the bolt. So the drill bit would extend into the hole about 1/4 inch before it encountered the broken bolt.