When does the fault code 3714 go inactive?
3714 – Engine Protection Torque Derate- Condition Exists Conditions for Clearing the Fault Code This fault code will go inactive once all other active fault codes have been addressed. Refer to the appropriate fault code troubleshooting tree. The ECM will turn off the amber CHECK ENGINE lamp immediately after the diagnostic runs and passes.
What to do if your fault code does not clear?
Refer to the appropriate fault code troubleshooting tree. The ECM will turn off the amber CHECK ENGINE lamp immediately after the diagnostic runs and passes. A regen and SCR test was performed post repair. All of the temps looked perfect and it passed all of the tests. The 3712 and 3714 still would not go away, there were absolutely no other codes.
Can a Cummins engine be derated with another code?
These codes are also used with other Cummins engines, and the procedure is the same. The customer had some other codes that were active previously, and had already fixed the problem. However, the truck was still derated with the codes mentioned above and he wasn’t sure how to fix it. The procedure: 4) Codes will go inactive and can be cleared.
When does a Cummins fault code go inactive?
3712 – Aftertreatment SCR Operator Inducement- Data Valid but Above Normal Operational Range- Most Severe Level Conditions for Clearing the Fault Code This fault code will go inactive once all other active fault codes have been addressed. Refer to the appropriate fault code troubleshooting tree.
What does the code 3712 on the ECM mean?
This fault code is for information only, and indicates that an engine power derate and vehicle speed limit have been implemented in order to make sure that the critical SCR related fault codes that are presently active in the ECM are addressed as quickly as possible. Refer to Troubleshooting Fault Code 3712.
Is the code 3712 an operator fault or operator fault?
3232 also keeps popping up but I can clear it. Ok the 3712 I posted prior and is an operator fault so dont worry about this one. Aftertreatment Intake NOx Sensor – Abnormal Update Rate.
What happens when a fault code is not cleared?
Refer to the appropriate fault code troubleshooting tree. The ECM will turn off the red STOP ENGINE lamp immediately after the diagnostic runs and passes. 3714 – Engine Protection Torque Derate- Condition Exists Conditions for Clearing the Fault Code This fault code will go inactive once all other active fault codes have been addressed.
What does code 3714 mean on Westport HD?
When Fault Code 3714 is active, as described here, the torque derate associated with the fault will also be active. Drivers may complain of power and/or torque loss. Applicability This TSB applies only to manual transmission EPA10 model Westport HD system-equipped vehicles displaying Cummins®fault code 3714 and no other active codes. Resolution
What does code 3714 mean on a Cummins car?
Cummins®fault code 3714 present with no other codes active. Note that the information covered in this TSB is also contained in Cummins®Technical Service Bulletin TSB110187. Issue During an active regeneration, the aftertreatment fuel injector injects fuel into the exhaust stream to raise the temperature of the exhaust.
What does return code 3762504530 mean?
I had this same return code (3762504530) when trying to use a service account to run a scheduled task for a data import. My issue was the service account couldn’t access the log file.
What is section 3714 of the US Constitution?
Section 3714 is referred to in sections 1532, 1535, 3326, 3327, 3716 of this title.
What are the cross references in section 3714?
Cross References. Section 3714 is referred to in sections 1532, 1535, 3326, 3327, 3716 of this title.
Where is the serial number on a Kawasaki engine?
Kawasaki Engine model and serial numbers are located on a tag attached to the rear of the engine on the engine housing. See image below for reference. The CODE number above the barcode is made of the model and the spec number.