What was the 2003 CRV p1259 failure error?
2003 CRV. P1259 Vtec failure error. Power cuts out around 3K RPM’s. Test and replaced VTEC Solenoid Valve and Pressure Switch. Remove, cleaned screens which were partially clogged, and tested VTC Oil Control Valve. Appears to function fine.
What is the VTEC oil pressure switch error code p1259?
Error Code P1259 is detected when there is a problem in the VTEC oil pressure switch or at the VTEC solenoid valve circuit. Common Symptoms. As with other error codes, Error Code P1259 activates the Check Engine light and registers the code to the vehicle’s memory system.
What kind of spool valve does Acura CRV use?
Spool Valve Assembly with Oil Pressure Switch – VTEC Solenoid – Compatible with Honda & Acura Vehicles – Accord 2.4L, Civic 2.0L, CR-V, Element, RSX – Replaces 15810RAAA03, 15810-RAA-A01, 917224 Tecoom 15810-RAA-A03 Spool Valve Body VTEC Solenoid Body with Timing Oil Pressure Switch and Gasket for Honda CRV CR-V Civic Element Accord Acura RSX
When do I get an error code p1259?
Error Code P1259 is detected when there is a problem in the VTEC oil pressure switch or at the VTEC solenoid valve circuit. As with other error codes, Error Code P1259 activates the Check Engine light and registers the code to the vehicle’s memory system.
2003 CRV. P1259 Vtec failure error. Power cuts out around 3K RPM’s. Test and replaced VTEC Solenoid Valve and Pressure Switch. Remove, cleaned screens which were partially clogged, and tested VTC Oil Control Valve. Appears to function fine.
What should I do if my p1259 VTEC fails?
P1259 Vtec failure error. Power cuts out around 3K RPM’s. Test and replaced VTEC Solenoid Valve and Pressure Switch. Remove, cleaned screens which were partially clogged, and tested VTC Oil Control Valve. Appears to function fine. Removed VTC Filter assembly, screen was torn from o-ring, replace filter assembly.
Why is my Honda Accord p1259 not working?
This is facilitated by sending oil into the VTEC system, which changes the engine timing. A good rule of thumb is that if the P1259 code sets at 4000 RPM or below, it’s usually the VTEC pressure switch wiring issue or bad switch. If it is set at 4000 RPM or greater, it’ll usually be an oil related issue.
Why does my car have an error code p1259?
As with other error codes, Error Code P1259 activates the Check Engine light and registers the code to the vehicle’s memory system. Other than that, there are usually no drivability issues and concerns that go along with this error code. This error code can be caused by multiple of factors, such as: Low oil pressure or low engine oil level
What was the 2003 CRV VTEC failure error?
P1259 Vtec failure… 2003 CRV. P1259 Vtec failure error. Power cuts out around 3K RPM’s. Test and replaced VTEC Solenoid Valve and Pressure Switch. Remove, cleaned screens which were partially clogged, and tested VTC Oil Control Valve.
P1259 Vtec failure error. Power cuts out around 3K RPM’s. Test and replaced VTEC Solenoid Valve and Pressure Switch. Remove, cleaned screens which were partially clogged, and tested VTC Oil Control Valve. Appears to function fine. Removed VTC Filter assembly, screen was torn from o-ring, replace filter assembly.
What’s the engine code on a 2002 Honda CRV?
Vocational, Technical or Tra… Honda Crv: 2002 Honda CRV has code p1259. Cars engine will 2002 Honda CRV has code p1259. Cars engine will not run past 2500 rpm’s starts to cut out and will not accelerate. … read more
Can a Honda CRV p1259 VTEC malfunction?
Typically, there aren’t many symptoms associated with P1259. You’ll get the check engine light, that’s usually about it. If the VTEC system isn’t working at all you may notice a dip in power. The VTEC system controls the valve timing in your Honda.
P1259 Vtec failure… 2003 CRV. P1259 Vtec failure error. Power cuts out around 3K RPM’s. Test and replaced VTEC Solenoid Valve and Pressure Switch. Remove, cleaned screens which were partially clogged, and tested VTC Oil Control Valve.
What are the possible causes of Honda p1259?
P1259 Honda Possible Causes. Low engine oil level or oil pressure. Faulty Variable Valve Timing and Lift Electronic Control (VTEC) solenoid. VTEC Solenoid harness is open or shorted. VTEC circuit poor electrical connection. Faulty VTEC oil pressure switch.
How does the VTEC system work on a Honda CRV?
The VTEC system controls the valve timing in your Honda. It does this by activating the VTEC/Rocker arm solenoid. It uses the Rocker Arm oil pressure switch to monitor the pressure of this system. P1259 specifically means that there is an issue with the VTEC circuit itself.