What to do when your clutch stalls in first gear?
My friend used to have this problem, when he used to do cold starts hed fire his bike up then apply the back brake, hed then rev the engine grab the clutch and put it into gear, it would make a big clunk but then be fine for the rest of the day. This post is not being displayed . The clutch is sticking overnight, do you have the correct oil in it?
Why does my bike stall when put into 1st gear?
So I recently replaced my clutch plates and fibres and finally had a chance to ride the bike. Upon start up, I let the bike warm up, held clutch in and then put the bike into gear, and it immediately jumped and stalled. It keeps doing it and I can’t ride the bike. The clutch has been bled properly with 0 bubbles.
Can you shift from neutral to 1st gear?
If you don’t want to pull the plates you could lay the bike on the clutch side and I think that the oil would pool in the clutch area and maybe soak your plates. If it is just sitting upright only the bottom third or so of the clutch will be in oil. Can you shift from neutral into gear give the bike some gas and take off?
Can a bike go into 1st gear with the clutch in?
I have a 2005 crf250r and went to go riding the other day and when i got the bike started and warmed up i went to shift it into 1st gear with the clutch in and it immediately stalled. I had this problem a month or so ago as well and all i did was adjust it out, and then back in and it was fine.
So I recently replaced my clutch plates and fibres and finally had a chance to ride the bike. Upon start up, I let the bike warm up, held clutch in and then put the bike into gear, and it immediately jumped and stalled. It keeps doing it and I can’t ride the bike. The clutch has been bled properly with 0 bubbles.
My friend used to have this problem, when he used to do cold starts hed fire his bike up then apply the back brake, hed then rev the engine grab the clutch and put it into gear, it would make a big clunk but then be fine for the rest of the day. This post is not being displayed . The clutch is sticking overnight, do you have the correct oil in it?
If you don’t want to pull the plates you could lay the bike on the clutch side and I think that the oil would pool in the clutch area and maybe soak your plates. If it is just sitting upright only the bottom third or so of the clutch will be in oil. Can you shift from neutral into gear give the bike some gas and take off?
I have a 2005 crf250r and went to go riding the other day and when i got the bike started and warmed up i went to shift it into 1st gear with the clutch in and it immediately stalled. I had this problem a month or so ago as well and all i did was adjust it out, and then back in and it was fine.
Why does my Fazer stall when I put it in first gear?
I know on my Fazer, if the side stand is down and I go to put it into 1st gear from neutral, the engine will cut out. This is the switch working correctly. If it developed a fault it either wouldn’t cut the engine, or it would sense that the stand was down, even if it wasn’t.
Why does my yamahaxj600 stall in first gear?
This invariably happens with my YamahaXJ600. It can usually be solved by pulling the clutch in and giving the engine a couple of quick blips of the throttle This usually frees the plate before trying to select first. This post is not being displayed . why would a faulty side stand switch cause only one stall, that makes little to no sense.
Why does my engine stall when I split a log?
A log that is too heavy will overload the hydraulic cylinder causing the engine to stall. Try splitting a different log to determine whether the log splitter is overloaded. A frozen or seized hydraulic pump can also cause the engine to stall. A blockage in the hydraulic hose or a damaged directional valve also stalls the engine.
What happens when you pull the starter rope on a log splitter?
The recoil starter spins the engine on the log splitter when you pull the starter rope, and the rope retracts when released. If the recoil starter assembly is broken, follow the steps in this repair guide to replace it. The fuel line carries the fuel supply from the gas tank to the carburetor.
Why is the engine on my log splitter surging?
A frozen or seized hydraulic pump can also cause the engine to stall. A blockage in the hydraulic hose or a damaged directional valve also stalls the engine. Why is the engine on my log splitter surging?