What kind of wiring harness does a Nissan 350Z use?
This harness is specifically engineered for a USDM LHD Z33 Nissan 350z (2003-2006) with the Turbo 2JZGTE VVTi or Non-Turbo 2JZGE VVTi engine swap. It was developed in house on an actual 2JZ VVTi engine to ensure a perfect fit to all engine connections.
Can a 2JZGTE engine swap work on a 350Z?
It’s FINALLY here – enjoy a fully functional interior in your 350z with a 2JZ VVTi engine swap. This Wiring Specialties CANbus harness does the trick! Tach, engine temp and ZERO fault lights for traction control or stability control. Have a properly running car again, with the power of a 2JZ VVTi engine.
How do you install a universal wiring harness?
After ripping out the old harness and cleaning up the connections that were still usable, it was time to install the new harness. We found it useful to lay out the entire harness and route each separate area at a time.
Where do you put the wiring harness in a car?
To start we routed all necessary wires to the rear of the car using the factory clips and trunk grommets. One important addition to note when installing any new wire harness is the incorporation of a wire loom or conduit.
This harness is specifically engineered for a USDM LHD Z33 Nissan 350z (2003-2006) with the Turbo 2JZGTE VVTi or Non-Turbo 2JZGE VVTi engine swap. It was developed in house on an actual 2JZ VVTi engine to ensure a perfect fit to all engine connections.
It’s FINALLY here – enjoy a fully functional interior in your 350z with a 2JZ VVTi engine swap. This Wiring Specialties CANbus harness does the trick! Tach, engine temp and ZERO fault lights for traction control or stability control. Have a properly running car again, with the power of a 2JZ VVTi engine.
Where is the 350Z oil pressure gauge located?
The harness utilizes a number of relays and controllers that OEM 350z, so they need to remain on the chassis fuse box, in stock form. For proper Oil Pressure Gauge function, the 350z OEM oil pressure sending unit needs to be used (located near the 1JZ Oil filter).
How to install a fuel injection wire harness?
1.0 Introduction 2.0 About These Instructions 3.0 Tools Needed 4.0 Pre-Installation and Harness Routing Guidelines 5.0 General Installation Instructions 6.0 60510 & 60511 Fuel Injection Harness Kit 7.0 Start Up 8.0 Trouble Shooting Instructions and Trouble Codes Sectionsare further divided into Paragraphs and Steps.
The harness utilizes a number of relays and controllers that OEM 350z, so they need to remain on the chassis fuse box, in stock form. For proper Oil Pressure Gauge function, the 350z OEM oil pressure sending unit needs to be used (located near the 1JZ Oil filter).
How many wires does the TP sensor have?
As you can see in photo 2 of 2 (in the image viewer) the TP sensor has 2 connectors for a total of 6 wires coming out of both. This is due to the fact that the throttle position sensor is two sensors in one.
How to troubleshoot the throttle position sensor ( TPS )?
Testing the throttle position sensor (TPS) to see if it has failed and causing a TPS diagnostic trouble code (DTC) is not hard. In this tutorial, I’m gonna’ show you how to troubleshoot the throttle position sensor (TPS) on your Nissan 3.3L Pathfinder (Frontier, XTerra or QX4), with a multimeter and in a step-by-step way.
Where is the oil pressure sensor on a Nissan 350Z?
For proper Oil Pressure Gauge function, the 350z OEM oil pressure sending unit needs to be used (located near the 1JZ Oil filter). In most cases a relocation line needs to be used in order to use the Nissan sensor with the swap. Harness connection will be provided to reach the passenger side shock tower for sensor relocation (optional).