What kind of transmission does a Jeep 3, 4 and 5 have?
Jeep/AMC 3, 4 and 5 speeds: Top loaded, cast iron case with non-synchronized 1st gear and 24 tooth 2nd/3rd syncro rings. Main shaft 1st/Reverse gear has 25 helical or straight cut teeth.
Do you have a 45RFE or 545RFE valve body?
If you have natural metal-colored springs in the areas indicated here, you have a 45RFE, 545RFE. If you have colored springs (PURPLE and ORANGE) in the areas indicated here, you have a 68RFE. A good rule of thumb is to replace the solenoid pack with the same color as the original in the vehicle.
Where can I find parts for a jeep transmission?
You can also locate parts to repair your Jeep 3, 4, and 5 speed manual transmission. These quality manual transmission parts and rebuild parts kits are designed to be top of the line overhaul kits.
Is the 68RFE the same color as the solenoid pack?
If you have colored springs (PURPLE and ORANGE) in the areas indicated here, you have a 68RFE. A good rule of thumb is to replace the solenoid pack with the same color as the original in the vehicle. The plate number is stamped in the small box between the two bolt holes.
How many engagement teeth does a Jeep Cherokee have?
Top loaded aluminum case and shift cover with either 13-32 or 13-40 casting numbers. Fully synchronized with 30 engagement teeth on 1st & 2nd and 27 engagement teeth on 3rd & 4th.
What kind of transmission is in a 1986 Jeep?
Used in 4 cylinder applications except 1986 6 cylinder. Front input bearing outside diameter is 80mm. End loaded, aluminum case transmission based on the Toyota “R” series. Used in 6 cylinder applications. Front input bearing outside diameter is 90mm. Aluminum case that is split vertically lengthwise.
How many teeth are in a jeep Syncro ring?
Top loaded, cast iron case and is fully synchronized in all forward gears. 1st gear syncro ring has 36 teeth with 33 teeth on 2nd/3rd. Casting number is 260XXXX. Side loaded, cast iron case with 9-bolt side cover. Fully synchronized with 36 tooth syncro rings. Top loaded, cast iron case with a flat, rectangular, tin, 10-bolt top plate.
Jeep/AMC 3, 4 and 5 speeds: Top loaded, cast iron case with non-synchronized 1st gear and 24 tooth 2nd/3rd syncro rings. Main shaft 1st/Reverse gear has 25 helical or straight cut teeth.
Used in 4 cylinder applications except 1986 6 cylinder. Front input bearing outside diameter is 80mm. End loaded, aluminum case transmission based on the Toyota “R” series. Used in 6 cylinder applications. Front input bearing outside diameter is 90mm. Aluminum case that is split vertically lengthwise.
When did the Jeep Cherokee get a new engine?
A stiffer unibody frame brought improvements to noise, vibration, and harshness (NVH) measurements. Also contributing to NVH improvements were new door seals that reduced wind noise at higher speeds. In the middle of the 1999 model year, vehicles with the 4.0 L engine received a revised intake manifold.
When did the Jeep Cherokee get a new intake manifold?
In the middle of the 1999 model year, vehicles with the 4.0 L engine received a revised intake manifold. This was done to help counteract smaller exhaust porting on the latest casting of cylinder heads, which was done to meet more stringent emissions control laws.
Where can I find the Jeep transmission ratio?
In addition to the below information you can find Jeep manual transmission ratio and size data on our site at: Jeep ratio data Jeep identification tag cross reference information is alos available. Jeep/AMC 3, 4 and 5 speeds: Top loaded, cast iron case with non-synchronized 1st gear and 24 tooth 2nd/3rd syncro rings.
How much horsepower does a four cylinder Jeep Wrangler have?
The four-cylinder engine might be techy, but it’s also very potent. The optional engine delivers 270 horsepower at 5,350 rpm and 295 lb-ft of torque down at 3,000 rpm.