What is the problem with my Mazda 323?
The throttle position sensor is most likely damaged or worn out. You can order a replacement from BreakerYard and easily replace it yourself. Reading these common Mazda 323 problems should help you find out what is wrong with your Mazda 323 – or just what to look out for in the future.
Why is my ABS sensor not working on my Mazda 323?
This will not store any personal information) The ABS sensors are a common part to fail on the 323. If you have found that the ABS warning light has appeared on the dashboard, it will most likely be caused by a faulty ABS sensor.
Why does my Mazda 323 make a high pitched squealing noise?
You can hear a high-pitched squealing noise coming from the front of the car when the engine is running. The problem here is your timing belt tensioner pulley, which is one of the notorious weak spots on the 323.
Can you use E10 fuel in a Mazda 323?
Mazda’s advice is that you shouldn’t use E10 fuel in your 323. Continue to use regular unleaded. It’s not a problem we have heard about, but I suggest it’s related to the throttle position sensor. Take it to an independent mechanic experienced in Mazdas and they should be able to fix it.
The throttle position sensor is most likely damaged or worn out. You can order a replacement from BreakerYard and easily replace it yourself. Reading these common Mazda 323 problems should help you find out what is wrong with your Mazda 323 – or just what to look out for in the future.
You can hear a high-pitched squealing noise coming from the front of the car when the engine is running. The problem here is your timing belt tensioner pulley, which is one of the notorious weak spots on the 323.
This will not store any personal information) The ABS sensors are a common part to fail on the 323. If you have found that the ABS warning light has appeared on the dashboard, it will most likely be caused by a faulty ABS sensor.
Why does my Mazda 323 smell like fuel?
A bad contact in this switch was the cause of the problem. When starting the car for the first time in the day, there is a strong raw fuel smell emerging from the exhaust. It is only during some seconds that this can be noticed and it then disappears for the rest of the day.
How to reset immobilizer on a 1998 Mazda 323?
Turn key 1 back to ON. Observe illumination of security light in instrument panel. b. Turn key 1 to LOCK and remove key 1 from steering lock. Observe security light goes out. 3. Using key 2, start engine. Observe security light illumination (for 1-2 seconds ) and engine continues to run. a. Turn key 2 to LOCK and remove from steering lock. 4.
Is the 1998 Mazda 323 an Australian car?
yes it is a 1998 mazda 323, australian car, doesn’t crank or start. Good morning. Here is the immobilizer programming procedure for a 1998 Mazda 626 since I am in the USA, we don’t have the 323. They quit sending it here in 1989. The system is all the same on Mazda cars with immobilizer. Thanks Drew.
Where is the fuel flap on a Mazda 323?
Beyond that, the Mazda 323 should have a fuel-flap release lever on the floor, down beside the front-right hand corner of the driver’s seat. If the seat is positioned for a shorter driver, you may need to slide the seat back to reveal the release lever.
Why is my Mazda 323 making a growling noise?
If you look under the vehicle, oil will be clinging to the bottom of the sump. You will need to fit a replacement oil sump to rectify the situation. If you are hearing a real growling noise coming from the front of the car at the back of the engine, then the front exhaust down pipe is prone to failure on this car.
Can a Mazda 323 immobilizer be changed from another car?
To replace the immobilizer unit or PCM, there should be at least one valid key. Otherwise, both the immobilizer unit and PCM should be replaced. The immobilizer unit and PCM cannot be changed from one car to another. If the immobilizer unit or PCM is replaced with one from another car, the engine will not start.
How much does it cost to replace engine cap on Mazda 323?
If moisture gets in, it will cause the car to be difficult to start until the cap dries. If spark gets out, it will cause the engine to sputter. The cap only costs maybe $20 at your local part store and is very easy to replace. You should also replace the rotor at the same time as the cap.
Why does my Mazda 323 have a flashing orange hold light?
Recently my car’s dash has been displaying a flashing orange “HOLD”. It doesn’t happen all the time (twice in the last 2 or 3 weeks that I can think of) and the length of time it stays on for varies as well. I’ve checked Google for a bit of info, and I understand its a problem with the transmission, though I can’t get much more than that.
Where is the hold button on a Mazda 323?
The “Hold” you are referring to is in regard to the Overdrive/top gear lockout. The button located on your gear lever just below the “T” This button is for holding 3rd gear when going up steep hills etc. I just verified this with our Astina. So, it’s probably just a loose wire. Hopefully! Good Luck!
Mazda’s advice is that you shouldn’t use E10 fuel in your 323. Continue to use regular unleaded. It’s not a problem we have heard about, but I suggest it’s related to the throttle position sensor. Take it to an independent mechanic experienced in Mazdas and they should be able to fix it.