What is the diagnostic trouble code for a Jeep Cherokee?
One of the injector control circuit output drivers does not respond properly to the control signal. Check the circuits. http://m.cherokeeforum.com/showthread.php?t=24657&styleid=16
What does ECU stand for in Jeep Cherokee?
Jeep ECU – Electronic Control Unit Reset. The Electronic Control Module, or ECU as it is most commonly called, is a generic term used for any embedded system within a vehicle that controls one or more electric system(s) or subsystem(s). The following sequence is used to reset the ECM or PCM as it is sometimes refered too.
How to know if your Jeep Grand Cherokee has a DTC?
1.) Place the key into the ignition slot. 2.) Turn your key from OFF to ON four to five times in succession (do NOT start your vehicle). 3.) On the fourth or fifth time you turn your ignition ON, leave it in the ON position. 4.) Count the number of times your ‘Check Engine’ light flashes. This is your first number.
What happens if I Reset my Jeep ECM?
To finish off this post , here are a couple of things you should keep in mind. Resetting your Jeep ECM will not have any effect on your vehicle’s mileage, Resetting it should not cause any issues between your other module so feel free to this as many time as you want if you’re trying to diagnose a problem with your car. For good measure.
How do I find the trouble code on my Cherokee?
Trouble codes can be displayed by the MIL or by using a Scan Tool connected to the data link connector (OLC) Within 5 seconds switch the ignition key ON-OFFON-OFF-ON. Count MIL flashes. Note trouble codes. Each trouble code consists of two groups 0 [A]. The first group of flashes indicate the ‘tens’ of the trouble code.
When did Jeep Grand Cherokee PCM connector come out?
You can find the 1996-1998 4.0L Jeep Grand Cherokee PCM connector pin-out charts here: PCM Pin Out Chart (1996-1998 4.0L Jeep Grand Cherokee).
What was the diagnostic code for a 1995 Jeep Cherokee?
An open or shorted condition derected in the EGR solenoid circuit Possible air/fuel ratio imbalance not detected during diagnosis. http://www.jeepforum.com/forum/f13/obd-trouble-code-32-1995-orvis-636815/ Code 33. Air conditioning clutch relay circuit. An open or shorted condition detected in the air conditioning clutch relay circuit. Code 34.
What do the flashes mean on Cherokee 4.0?
The first group of flashes indicate the ‘tens’ of the trouble code. The second group of flashes indicate the ‘units’ of the trouble code. A short pause separates ‘tens’ and ‘units’ 0 [B]. A long pause separates each trouble code 0 [C]. For example: Trouble code 21 displayed 0.
What is the engine code for a Jeep YJ?
Jeep check engine codes for the YJ, XJ and other OBD1 jeeps. Jeep check engine codes for the Jeep Wrangler YJ and the XJ Cherokee. These codes and video may work with other OBD1 Jeeps. When Chrysler / Jeep came up with this idea for getting the engine codes, it was a very smart move.
What should I do about my 1999 Jeep Cherokee XJ?
1999 jeep cherokee XJ. ABS Light on. Got it scanned, came up with 2 codes. 1. Left rear sensor, so i bought that and am Hello and welcome to just answer. Replacing the left rear speed sensor should take care of your speed sensor code. Do that, then clear the codes.
Can you check the engine code on a Jeep Wrangler?
When Chrysler / Jeep came up with this idea for getting the engine codes, it was a very smart move. This generation of Wranglers and Cherokees had the most simple diagnostics of any other. You need no special scanner to get the trouble code.
One of the injector control circuit output drivers does not respond properly to the control signal. Check the circuits. http://m.cherokeeforum.com/showthread.php?t=24657&styleid=16
Jeep check engine codes for the YJ, XJ and other OBD1 jeeps. Jeep check engine codes for the Jeep Wrangler YJ and the XJ Cherokee. These codes and video may work with other OBD1 Jeeps. When Chrysler / Jeep came up with this idea for getting the engine codes, it was a very smart move.
When Chrysler / Jeep came up with this idea for getting the engine codes, it was a very smart move. This generation of Wranglers and Cherokees had the most simple diagnostics of any other. You need no special scanner to get the trouble code.
1999 jeep cherokee XJ. ABS Light on. Got it scanned, came up with 2 codes. 1. Left rear sensor, so i bought that and am Hello and welcome to just answer. Replacing the left rear speed sensor should take care of your speed sensor code. Do that, then clear the codes.
How to find the OBD code on a jeep?
When the light goes off, get ready to start counting the light flashings. Once the Check Engine Light has turned off, it will pause in the off position for a second or two, and then start to flash, count the flashes. Each OBD code stored will be given to you in a 2 digit sequence.
What does open or shorted mean on OBD1 Jeep?
41**: Alternator field control circuit open or shorted. 42*: An open or shorted condition detected in the auto shutdown relay circuit. An open condition detected in the ASD relay output circuit. An open or shorted condition detected in the fuel pump relay control circuit. An open circuit between PCM and fuel gauge sending unit.