What happens when you restart a 1999 ml430?
I own a 1999 ML430, and the one anomally that I experience is that when I try to restart after it dies, the ignition goes into a continuous crank. It gets stuck in that mode and continues to crank unsuccessfully. Do you also experience this?
What happens when Mercedes lowers to the ground?
When the level sensors are damaged they can throw off the calibration procedure. The vehicle can’t level itself, and it continues releasing air from via the pressure release valve. Eventually, your Mercedes-Benz lowers to the ground or it can also raise to the maximum setting.
Why does my Mercedes-Benz ml-320 shut off?
2009 ML-320 – same problem but happens very rarely, often a month between. Drive 30 minutes with a lot of stop and go. Try to restart a few minutes later, the starter turns over 10 seconds and then stops. Wait 10 minutes and it starts and works perfectly. I replaced the crankshaft sensor a few months back and it has happened twice since then.
Are there any problems with the Mercedes CL500?
Keep track that the ABC fluid is good is another important issue with any ABC equipped Benz. These cars are heavy. Your going to burn through front pads and tires every 20,000. But my CL is a pleasure and has been very dependable car overall. My 2000 CL500 just hit 88]
How does the fuel pump work on a CL500?
The pump sends air into the manifold to dilute the rich air/fuel mixture when the motor is cold.
How often should you change the oil on a Mercedes CL500?
1. Frequent Mobil 1 Synthetic Oil Services. 2. Change Transmission oil at around 75K or 5 years. 3. Always Keep clean air filters. 4. Keep good, mercedes brand belts on the car. 5. Align all 4 wheels immediately after tire replacement. 6. Brake fluid flush every 2 Years. 7. Cabin filters anually. 8. Keep sunroof track lubricated.
Is there a recall on the CL500 air pump?
You can thank the EPA for that one… it dosen’t actually purify anything, rather just tricks the computer to “think” it is burning cleaner… anyhow, there is a recall for the relays that operate the air pump, and they stick open causing the pump to stay running and burn out. The $40 relay burns up a $400 pump.
I own a 1999 ML430, and the one anomally that I experience is that when I try to restart after it dies, the ignition goes into a continuous crank. It gets stuck in that mode and continues to crank unsuccessfully. Do you also experience this?
2009 ML-320 – same problem but happens very rarely, often a month between. Drive 30 minutes with a lot of stop and go. Try to restart a few minutes later, the starter turns over 10 seconds and then stops. Wait 10 minutes and it starts and works perfectly. I replaced the crankshaft sensor a few months back and it has happened twice since then.
Why is my Mercedes Benz M class not starting?
I took it to autozone and it said the EGR Valve was bad. It was replaced yesterday and today when I drove my car, it shut off while I was driving it and now it won’t start. Just had the crankshaft position sensor replaced today and now my SUV has started and will post if the problem still happens.
How to reset the computer code on a Mercedes C class?
Turn the ignition switch to “ON.” Press the power button on the scan tool, if it does not come on automatically. Wait for the tool to complete the scanning process. Press the “Reset” or “Erase” button on the scan tool to reset the computer codes. “Mercedes-Benz C-Class Operator’s Manual”; Mercedes-Benz USA, LLC; 2010
What kind of engine does the ML 430 have?
ML 430 is a five-door sport utility vehicle manufactured from 1999 until 2001. It is available as rear-wheel or front-wheel drive. It is produced with 4,266 cc petrol engines. This model?s engine can produce power of 200 kW. Car is available with manual and automatic transmission style.
What to do when your Mercedes Benz shuts off?
Drive 30 minutes with a lot of stop and go. Try to restart a few minutes later, the starter turns over 10 seconds and then stops. Wait 10 minutes and it starts and works perfectly. I replaced the crankshaft sensor a few months back and it has happened twice since then. 23 people found this helpful.
What’s the problem with my 2009 Mercedes ml-320?
2009 ML-320 – same problem but happens very rarely, often a month between. Drive 30 minutes with a lot of stop and go. Try to restart a few minutes later, the starter turns over 10 seconds and then stops. Wait 10 minutes and it starts and works perfectly.
When did the first Mercedes Benz come out?
Officially founded in 1926, Mercedes can trace its origins as far back to the creation of the first petrol-powered car in 1886. It’s now a division of the German company Daimler AG, and its headquarters are in Stuttgart, Germany.
Can a 2002 Mercedes Benz drive cycle be incomplete?
Also, one customer with a 2002 Mercedes was unable to complete the secondary air injection monitor until one evening he allowed his vehicle to idle for 5-20 minutes in his driveway. He then turned off his vehicle and restarted the vehicle the next morning and allowed it to idle for another 5-10 minutes.
What kind of car is the 1999 Mercedes Benz ml430?
The 1999 Mercedes-Benz ML430, the second model in the company’s M-Class line, lends a hefty dose of status to the SUV market. It’s as if Tiffany or Escada got into off-roading.
Are there any Mercedes-Benz ML 320s for sale?
Try changing your search criteria or remove filters. Anything catch your eye? Autotrader has 3 Used Mercedes-Benz ML 320 cars for sale.
What’s the price of a 1999 Mercedes Benz?
The base price is even somewhat reasonable – $43,750 before adding such options as the $1,050 Bose premium audio system and the $1,095 glass sunroof But we found in some respects the ML430 does not live up to the storied Mercedes brand name. She: You’ve heard of trophy wives and trophy kids.
Are there any problems with my Mercedes Benz?
THE ONLY PROBLEMS I EVER HAD WITH MY CAR WAS THE GLOVE COMPARTMENT WOULDENT CLOSE PROPERLY AND THE CUP HOLDER TO THE LEFT OF THE STEERING WHEEL WOULD NOT CLICK SHUT I HAD TO PUT A PAPER WEDGE IN THERE TO KEEP IT CLOSED.
Can a pre 2000 ml lose its settings?
On the early pre 2000 ml’s the aam can loose it’s settings when disconnected from the battery. These can include the ignition key sync or even the keys rfid information. If when you try to start it starts then run some for maybe a half second before shutting down this could be your problem.
Why does my ML not start while driving?
One might be the cause of the battery drain or not starting then your ML may have lost the key information. If it wouldn’t start or it stop while driving but after say 30 minutes it would start and run normally then it might be your crank shaft position sensor. $50 sensor back of engine drivers side about 10 minutes to diy fix.
What causes a Mercedes Benz to stall and not start?
Symptoms of a defective crankshaft position sensor on a Mercedes-Benz. Engine Cranks but no Start, Dies, Stalls, or Backfires. A failed crankshaft position sensor can cause your engine to stall or not start at all. Your Mercedes-Benz may start and run for a short time, or until it gets warm and then it dies.
Why does the crankshaft position sensor stop working?
There are several failure crankshaft position sensor symptoms that you should pay attention to. Many engine models stop functioning if this component fails to send accurate signals. The speed and position of the crankshaft are two key parameters that the car’s computer uses for engine management calculations.
What happens if the crankshaft sensor does not work?
If the crankshaft position sensor fails, it will not send information about the position of the crankshaft and speed of the engine RPMs to the ECU. As a result, the ECU doesn’t know when to send the spark plugs and how to adjust the fuel mixture. This can cause your car to stall or hesitate to start.
What happens if the crank on a Mercedes Benz goes bad?
Symptoms of a defective crankshaft position sensor on a Mercedes-Benz. Failed crankshaft position sensor can also impact the idling, the acceleration, or even your transmission shifting. In some cases, it can cause your transmission to go into limp mode. You may also notice an increase in engine vibrations.
Symptoms of a defective crankshaft position sensor on a Mercedes-Benz. Engine Cranks but no Start, Dies, Stalls, or Backfires. A failed crankshaft position sensor can cause your engine to stall or not start at all. Your Mercedes-Benz may start and run for a short time, or until it gets warm and then it dies.
Where is the crankshaft position sensor on a Mercedes Benz?
Locate the crankshaft position sensor (CPS) on driver’s side, towards the rear of engine. Back of engine, near the firewall. This opens in a new window. Unplug the electrical connector from the CPS sensor. Squeeze the connector and pull it away from the CPS sensor. This opens in a new window. Remove bolt. Remove the crankshaft position sensor.
Can you jump start a Mercedes Benz with a dead battery?
Note: Jump starting a car with a fully discharged battery will shorten the life of the battery or damage the battery. Hint: For a safer method to jump start a Mercedes-Benz with a fully discharged battery see Method 3. Method 2 Jump start your car battery with a booster pack / jump starter box.
What causes battery to die on Mercedes medic?
A defective electrical system, Control Unit or a fault on the CAN Bus (Controller Area Network) are also causes that can cause your Mercedes-Battery battery to die. To troubleshoot the current draw, you need a multimeter that can perform current reading.
How to jump start a W220 S500 S500 with dead battery?
This guide will show you how to jump start any of these cars: S430 S500 S600 S55 AMG | CL500 CL600 CL55 AMG. The easy way to jump start your S-Class is via the battery in the trunk. If the battery is dead and you can’t manually unlock the trunk, there is another method to jump start the car.
Note: Jump starting a car with a fully discharged battery will shorten the life of the battery or damage the battery. Hint: For a safer method to jump start a Mercedes-Benz with a fully discharged battery see Method 3. Method 2 Jump start your car battery with a booster pack / jump starter box.
How old is the battery on a Mercedes Benz?
This may seem obvious, but an old battery is the root of many headaches and can cause all sorts of malfunctions on Mercedes-Benz cars. How old is the battery on your Mercedes-Benz? While some MB owners have pushed over 10 years on an original battery, the battery should be considered for replacement around 6 or 7 years.
Why is the battery on my Mercedes Benz not working?
Hint: Starter Problem or Low Battery This may seem obvious, but an old battery is the root of many headaches and can cause all sorts of malfunctions on Mercedes-Benz cars. How old is the battery on your Mercedes-Benz?
Why is my Mercedes-Benz ML320 not starting?
A no start condition may develop due to an anti-theft system fault. If the drive authorization module fails to recognize the keys, the engine will not start. In many cases, a new module and keys will be needed to correct this problem. The average cost for a Mercedes-Benz ML320 No Start Diagnosis is between $143 -$180.
Why does my Mercedes Benz engine not start?
However, when i turn the key all the way, the engine does not even try to crank. It almost feels as if only the starter is disconnected or something from the car entirely. (I know nothing about car engines)
Is the starter on my 1998 MB 320 Ml working?
My 1998 MB 320 ML, Was stopped about 15 days, now the starter don’t work , only make a sound (tac, tac, tac) but don’t crank, I check the battery it has 11.5 V. and charge again by 12 hr., I re programed the keys according manual but don’t crank.
Why is my Mercedes Benz starter not working?
Often times, when the starter is defective or seizes up it will blow out the fuse that protect the starter circuit. Another thing that you can try is to hit the starter with a rubber hammer a couple of times. Depending what kind of starter problems you have, the starter may work a few more times.
Why does my Mercedes not start when I charge the battery?
This Mercedes-Benz is not starting because of a low battery. In this case, what you need to do is trickle charge your battery using any of these 12 volt battery trickle chargers. If you need help read this article on How to charge a Mercedes-Benz the right way. Mercedes won’t start, and it’s not the battery.
What’s the average life of a starter motor?
A starter is a motor for starting the engine of your Passat. The average life of a starter motor is about 100,000 to 150,000 miles, and the life will be shortened if the engine is started more frequently.
Why is my Ford’s Max not starting?
A test can be done to measure the voltage between the battery poles, check the acid level and assess the condition of the starter battery. If a new car battery has been installed, the battery may not have yet reached its full capacity. There is nothing to worry about. A new battery only develops its full capacity over time.
Drive 30 minutes with a lot of stop and go. Try to restart a few minutes later, the starter turns over 10 seconds and then stops. Wait 10 minutes and it starts and works perfectly. I replaced the crankshaft sensor a few months back and it has happened twice since then. 23 people found this helpful.
When does the engine stall in a Mercedes?
There are never any notifications on the dash or any signs of it beginning to fail. This typically happens when I’m slowing down at an intersection or just driving slower in traffic.
What should you do if your car shuts off while driving?
When your car shuts off while driving on the road randomly, the first thing you should check is your car fuel tank. An empty fuel tank happens to most of us. Of course, you can not drive a car with no fuel. Thus, looking at the fuel gauge may definitely save you from standing on the roads for hours and hours.
Are there any problems with the Mercedes c230wz?
The contact owns a 2006 Mercedes-Benz C230wz. While driving 50 mph, the vehicle shut off without warning. The vehicle was towed home. The dealer was not made aware of the failure. The vehicle was not diagnosed or repaired. The manufacturer was notified. The failure mileage was 110,000.
What causes a car to stop while driving?
The crankshaft sensor is a necessary part to make your car engine running on a lot of car models. On some car models, you do also have a camshaft position sensor, which the car uses if the camshaft sensor is faulty. In this case, a faulty crankshaft position sensor may not cause the car to stop entirely.
What are the problems with a Mercedes Benz?
Top 5 Mercedes-Benz no start problems 1 Engine Click, No Start 2 Engine Dies Right After It Starts 3 Car turns over, but it won’t start 4 The car makes a clicking noise but won’t start. Hint: Starter Problem or Low Battery 5 Key will not turn the ignition More …
What should I do if my Mercedes Benz won’t start?
Start the car and you should be able to get around 60 psi. When the engine is running and when you turn off the engine the pressure should stay steady. Always perform this test on a cold engine. Next, make sure that the fuel injector connections are secure and not loose. Check the fuel pump and the fuel pump relay.
What causes a Mercedes Benz to not start?
In most cases you will get a fault code related to one of the following: 1 ECM / PCM computer failure 2 Camshaft position sensor 3 Shifter Selector module 4 Fault codes related to driver authorization or immobilizer 5 Electrical problems
Top 5 Mercedes-Benz no start problems 1 Engine Click, No Start 2 Engine Dies Right After It Starts 3 Car turns over, but it won’t start 4 The car makes a clicking noise but won’t start. Hint: Starter Problem or Low Battery 5 Key will not turn the ignition More
Why is my brake light not working on my Mercedes?
Yes it could be the brake light switch. It could be other problems such as low brake fluid level or failed ABS wheel speed sensor. There is no certain way to know without first doing some troubleshooting. Where is the brake light swtich located on a Mercedes-Benz? Right above the brake pedal.
Why does my Mercedes Benz make a clicking noise?
It requires electrical power to crank the engine. The car makes a clicking noise but won’t start. Hint: Starter Problem or Low Battery This may seem obvious, but an old battery is the root of many headaches and can cause all sorts of malfunctions on Mercedes-Benz cars.
What to do if your Mercedes key won’t turn?
If you have this problem you will have to install a new / virgin EIS. You can not install a used unit because the EIS has to be paired / married to the car using Mercedes-Benz Star Diagnostic Software. They key itself may be the reason why the car doesn’t start. The key may open the doors, but it will not start the car.
What to do if the key does not turn in the ignition?
If the key does not turn in the ignition, try moving the steering wheel as you try to turn the key. The steering wheel will feel completely solid if you try to move it in one direction and may move slightly in the opposite direction.
What kind of car won’t start when you turn the key?
The same has happen to my car 2008 C350. 3 Month ago the car won’t start I got it towed to the mechanic once it got off the tow truck it started. Later to this month it wont start and doing the same. I turn the key but noting.
How many times has my Mercedes C class not started?
It will cost you around 1200 to replace because of the computer system. 66 people found this helpful. My 2010 C300 has been towed 5 times in 3 years as it won’t start. Today, first warm and humid day – call the tow truck. The dealer has no idea !!
Why does my Mercedes Benz C300 not start?
I’m having the same issue with my Mercedes Benz C300 2008-the first time I was stuck on the 12th floor and no tow truck would fit in the parking garage-we ended up rolling it down the 12 floors. The battery was so dead that the wheel wouldn’t turn, the ligts went on and the dash lit up but the car just wouldn’t start.
What causes a Mercedes Benz M class to stop?
11 people found this helpful. Hi Mark, car was stopping due to disconnection of wiring on footwell under carpet. This was caused by blockage on water vent under box below windscreen causing water to enter car down footwell. Regards, Bryan 6 people found this helpful.
11 people found this helpful. Hi Mark, car was stopping due to disconnection of wiring on footwell under carpet. This was caused by blockage on water vent under box below windscreen causing water to enter car down footwell. Regards, Bryan 6 people found this helpful.
When did the Mercedes Benz ML 430 come out?
The ML 430 is an all-wheel-drive, V8-powered, four-door sports utilityvehicle introduced for the 1998 model year. The M-Class comes in three variations. There’s the ML 430, and the ML320 with a V6 engine, which costs about $8,000 less.
What’s the difference between the ML 430 and ML320?
There’s the ML 430, and the ML320 with a V6 engine, which costs about $8,000 less. Finally, there’s a hot-rod ML 55 AMG; it costs about 10 grand more than the 430. There are lots of good things about this vehicle. The ML 430 has a 268-horsepower engine that’s quite powerful. Its acceleration and braking are top notch.
What’s the difference between the Hot Rod ML 430 and 55 AMG?
There’s the ML 430, and the ML320 with a V6 engine, which costs about $8,000 less. Finally, there’s a hot-rod ML 55 AMG; it costs about 10 grand more than the 430. There are lots of good things about this vehicle.
Do you have a Mercedes-Benz double shifting problem?
I have a C350 2009 that has a transmission double shifting problem from 11K miles. When car is cold, once you pass from park to drive with the brakes applied, Top 765 Mercedes-Benz Reviews Trending Car Warranties Home Warranties Medical Alert Systems Invisible Braces Gold IRA Movers Buyers Guides News Login Write a review Follow us:
Why does my Mercedes medic draw so much battery?
A radio receiver in the car continuously listens for wake up signal from the key. As the car receives a signal in the assigned frequency it wakes up to validate the key. This causes current draw for several seconds. If the car is left parked in high pedestrian traffic areas this could be a problem.
Why does the engine stop cooling at 3000rpm?
The ” stops cooling at 3000rpm ” is exactly what @Anarach stated, in that the clutch disengages above this to allow more power to the engine. It could also do this so as to not over spin the A/C compressor. If you’re engine is hitting the 3000rpm at 100kph, this is probably the reason.
Why is my AC not working at 3000 rpm?
While I cannot promise the values will work for your Lancer due to regional variations, the fact that there is a high-side cutoff can explain the AC not working above 3000 RPM. What’s so special about 3000 RPM?
Why is my My2K ml430 stuck in wait mode?
My MY2K ML430 battery was replaced last night by emergency MB service. I came home to enter the radio code and now it is stuck in WAIT. I noticed on my service receipts that there are two codes listed. I want to try it again, but don’t know how to get it back to “enter the code” mode.
When to replace battery in Mercedes medic medic?
Make sure you have a fully charged battery. If your battery is over 6 years old, you should consider replacing it to avoid further electrical nightmares. You can save on the cost of the battery by purchasing it online. For example, see this list of AGM Group 94 batteries for Mercedes-Benz on Amazon. Turn off the lights.
Why does my Mercedes not start when I Turn on the ignition?
Despite this brand’s high quality, though, Mercedes’ can develop problems with or without regular car maintenance. There are a few theories about why your Mercedes refuses to start when you switch the key in the ignition.
When did the Mercedes Benz ML Class come out?
In this article, we consider the first-generation Mercedes-Benz M-Class / ML-Class (W163), produced from 1997 to 2005.
What to do if your Mercedes ignition switch is not working?
If you have a spare key try to see if you are experiencing the same symptoms with the other key. If the other key works, keep using it for a couple of weeks to verify that the issue is really the key and not the EIS. Try scanning your Mercedes-Benz for fault codes. Ideally using a Start Diagnostic Scanner.
Why does my Mercedes Benz not turn on?
A problem that Mercedes-Benz owners may face is the key no longer turns in the ignition. This issue is often caused either by a defective key, bad shifter module, a failed Electronic Ignition Switch (EIS) also known as the EIS-EZS or a bad steering lock module (ESL).
Why is the brake light switch on my Mercedes not working?
If you don’t see the letters on the cluster change from P to R to N, it is a good sign that the gear selector module is defective. You can buy a new brake light switch on Amazon for less than $15 USD, just do a search for Mercedes-Benz Brake Light Switches.
When did the Mercedes-Benz ML 450 Hybrid come out?
At the 2009 New York International Auto Show, Mercedes-Benz showed their ML 450 Hybrid SUV, which was announced on 8 April 2009. The ML 450 Hybrid consumes almost 50% less fuel than the ML 550 does, even though it produces over 90% of the power generated by the V8 model.
What kind of car is a 2000 Mercedes-Benz ML320?
Upon a trip home to sc from west tx, id initially wanted a domestic suv (expedition,ect) but after a short test drive of the 2000 ml320 i quickly changed my mind! As with any used car i was very Read full review
Is the Mercedes-Benz ML the same as the M class?
This forced Mercedes-Benz to defer to a double-tiered marketing strategy of “ML” badging (e.g. ML 320) under an M-Class umbrella. There has been some confusion surrounding this nomenclature, with many sources erroneously referring to the series as the “ML-Class”, including Mercedes-Benz itself.
Is the Mercedes-Benz M Class ML 430 sport utility?
Used 2000 Mercedes-Benz M-Class ML 430 Sport Utility 4D Edit OptionsMileage: 157,858 4.1 Consumer Write a review View Gallery For Sale 36 Mercedes-Benz M-Class vehicles nationwide. Used 2002
How much does a 2000 Mercedes ML cost?
Used 2000 Mercedes-Benz M-Class ML 430 Sport Utility 4D Prices | Kelley Blue Book See pricing for the Used 2000 Mercedes-Benz M-Class ML 430 Sport Utility 4D. Get KBB Fair Purchase Price, MSRP, and dealer invoice price for the 2000 Mercedes-Benz M-Class ML 430 Sport Utility 4D.
What kind of car is the Mercedes ML?
Used 1999 Mercedes-Benz ML 320 4MATIC $2,995 Triangle Toyota de San Juan Used 1999 Mercedes-Benz ML 430 4MATIC $3,995 Reduced Bittons Auto Sales Used 2000 Mercedes-Benz ML 320 4MATIC $4,995 Reduced Ride One Auto Sales Used 2002 Mercedes-Benz ML 320 4MATIC $4,995 507 Motorsports Used 2001 Mercedes-Benz ML 320 4MATIC $4,995 G and J Car Sales
When did the Mercedes-Benz ML 400 CDI come out?
At the same time, the ML 430 was replaced by the 5.0-litre V8-powered ML 500 and a new 4.0-litre V8 turbodiesel ML 400 CDI became available in Europe. The following year, in 2002, Mercedes-Benz launched the ML 350 fitted with a 3.7-litre V6 engine. The ML 350 replaced the ML 320 in some markets, but supplemented it in others.
It requires electrical power to crank the engine. The car makes a clicking noise but won’t start. Hint: Starter Problem or Low Battery This may seem obvious, but an old battery is the root of many headaches and can cause all sorts of malfunctions on Mercedes-Benz cars.
When to remove oil from Mercedes Benz engine?
If the level is between the Low and High marks you don’t need to add any more oil. If the engine oil level is below the Low mark add oil until the level shows between Low and High. If the engine oil level is above the High/Max mark, you should remove oil from the engine to avoid damage to your car.
I took it to autozone and it said the EGR Valve was bad. It was replaced yesterday and today when I drove my car, it shut off while I was driving it and now it won’t start. Just had the crankshaft position sensor replaced today and now my SUV has started and will post if the problem still happens.
Can a bad crankshaft sensor cause the engine to stall?
If the crankshaft position sensor or its wiring have any issues, it can cause the crankshaft signal to be cut off while the engine is running, which can cause the engine to stall. This is usually a symptom of a wiring problem, however a bad crankshaft position sensor can also produce this symptom.
What causes cranking no start on Mercedes OM642?
Cranking No Start conditions are a common concern in our experience on Mercedes vehicles with the OM642 engine, and we’ve assembled a diagnostic process to help identify the root cause. Unfortunately, these problems rarely come with relevant DTCs. As with any Diagnosis, we’re going to start with the basics, use our senses, and gather information.
Start the car and you should be able to get around 60 psi. When the engine is running and when you turn off the engine the pressure should stay steady. Always perform this test on a cold engine. Next, make sure that the fuel injector connections are secure and not loose. Check the fuel pump and the fuel pump relay.
What to do if your car cranks but wont start?
This is a simple quick fix to start your car, it cranks up but wont turn over/start. Just try this before you replace Fuel pump and all sorts of costly autoworks. Relay Testing wont see this problem so you just by pass the relay to check if its not the culprit thats not passing the electricity through. This video is about how you By Pass the relay.
Why is the ESP light flashing on my Mercedes?
If pressing the ESP switch does not turn off the light, or if the ESP light is flashing, it means there is a problem with the ESP system on your Mercedes-Benz. This article will help you diagnose ESP problems on your Mercedes-Benz. Toggle ESP light on / off by pressing ESP button. Shown on SLK/Crossfire.
Can a Mercedes-Benz have a transmission failure?
Very few Mercedes-Benz cars have had complete transmission failure and require transmission replacement. We see these transmission fail in rare cases when water enters the transmission via the oil cooling lines or the radiator on cars equipped with Valeo radiators.
Why is my ML320 blowing hot air only?
A common problem with the ML320 / ML430 is the AC getting stuck on Hot or Cold setting. This is caused by the blend motor flap getting stuck and no longer moving when you rotate the AC knob between Hot and Cold. You can manually switch the blend motor flap if you remove the glove box.
How to fix stuck flap on ML320 ml430?
You can also manually switch the stuck flap to COLD settings if you need a temporary solution. Overwise buy the part above and replace it. This opens in a new window. Start by removing the glove box. Open the glove box and you will see the four screws that hold it in place.
2009 ML-320 – same problem but happens very rarely, often a month between. Drive 30 minutes with a lot of stop and go. Try to restart a few minutes later, the starter turns over 10 seconds and then stops. Wait 10 minutes and it starts and works perfectly.
What do I need to start my Mercedes Benz?
In order for your Mercedes-Benz to start there are several conditions that need to be met and also needs: Start enable by Drive Authorization System It requires electrical power to crank the engine. Requires fuel Requires spark