What does Engine code P1167 mean?

What does the error code p1166 stand for?

Error Code P1166 points to a problem in the heater circuit, possibly there is no voltage to the heater, or the heater is bad in the sensor. To diagnose, plug the sensor red pin (pin 2) and blue pin (pin 1) to the heater circuit. On the harness side, there must be 12V within 80 seconds of engine start.

When does the ECM set the DTC p1166?

The ECM sets DTC P1166 if no proportional fuel adaptation occurs for a defined time after the lambda controller has reached its minimum or maximum threshold. Need more information on how to fix the P1166 HYUNDAI code?

How much does it cost to repair a p1166 Hyundai?

The cost to diagnose the P1166 HYUNDAI code is 1.0 hour of labor. The auto repair’s diagnosis time and labor rates vary by location, vehicle’s make and model, and even your engine type. Most auto repair shops charge between $75 and $150 per hour. How much do you know about cars?

What does the OBD code p1166 mean?

Error Code P1166 is described as Air/Fuel Ratio Sensor 1 Heater Circuit Malfunction. This means a malfunction is detected in the Air/Fuel (A/F) ratio sensor stemming from an incorrect voltage value registered when the power was drawn to the sensor.

What does engine code p0160 mean?

What the P0160 code means. This code means that the powertrain control module has detected a fault in the circuit for the oxygen sensor for bank 2 sensor 2. The Check Engine Light will illuminate to let the owner know that there is a problem with the emissions system.

What does code p0136 mean?

A P0136 code may indicates that the the powertrain computer or PCM detects that the oxygen sensor voltage has remained below the expected range (in a lean condition, or below 400 millivolts) for too long. This criteria can vary from model to model.

What does engine code P1167 mean?

Error Code P1167 is described as Air/Fuel Ratio Sensor 1 Heater System Malfunction. This means the maximum voltage specified by the manufacturer for the vehicle has not been reached.

What does the P1167 Honda engine code mean?

Check for damaged components and look for broken, bent, pushed out, or corroded connector’s pins. What does this mean? The cost to diagnose the P1167 HONDA code is 1.0 hour of labor. The auto repair’s diagnosis time and labor rates vary by location, vehicle’s make and model, and even your engine type.

What does P1167 stand for in EVAP code?

The heater element is on until the engine is at normal operating temp then it switched off. P1167 is the upstream O2 sensor just before the cat. If it is anything like a evap code where the computer has to relearn the sensors parameters under varying load conditions by doing tests etc.

What was the error code on my Honda Accord?

I used to have both P1166 and P1167 error codes on my 2001 Honda Accord (F23A4 engine). I fixed the P1166 by replacing the O2 sensor. For about a day, everything looked wonderful (i.e. no check engine light on). Then, (after a day), the dreaded check engine light turned on again.

When does the Check Engine light come on in a Honda?

This article applies to the Honda Civic (1992-2000), and Accord (1990-2002). The check engine light in your Honda offers important diagnostic information, which will alert you of a serious problem like a bad catalytic converter. However, the check engine light also appears when the fuel tank cap is loose, or a change in humidity has occurred.

When to reset the Check Engine light on Honda Civic?

Continue reading to learn how to reset this light and save yourself the dealership cost. This article applies to the Honda Civic (1992-2000), and Accord (1990-2002). The check engine light in your Honda offers important diagnostic information, which will alert you of a serious problem like a bad catalytic converter.

What is the code for the Honda check engine light?

A long flash (or approximately one second) equals 10. A short code (or approximately half a second) equals one. For example, two long flashes followed by two short flashes will equal to the code 22. Any subsequent codes will follow in 2.5 second intervals.

Where is the jumper plug on a Honda?

(Related Article: Warning Lights – Honda-Tech.com) In the passenger’s side foot well, remove the kick panel by the side door. This will allow you access to the Engine Control Unit (ECU) and jumper plug (service connector). Depending on your Honda’s model, the jumper plug is either a blue or gray colored two-pin wire plug.

Navigation