What does code p0138 on O2 sensor mean?
A code P0138 may mean that one or more of the following has happened: 1 Faulty O2 sensor 2 Short to battery voltage in O2 sensor signal circuit 3 High fuel pressure (not as likely)
What is the diagnostic code for O2 sensor circuit Bank 2?
P0138 is a diagnostic trouble code (DTC) for “O2 Sensor Circuit High Voltage (Bank 1, Sensor 2)”.
When does the O2 sensor turn on the Check Engine light?
The engine control module (ECM) sees the voltage of the O2 sensor for bank 1 sensor 2 above 1.2 volts when the ECM has commanded the fuel to a targeted lean condition on that bank of the engine. The ECM detects the voltage high problem and turns on the Check Engine Light.
Where is the oxygen sensor located on an OBD-2?
This diagnostic trouble code (DTC) is a generic powertrain code, which means that it applies to OBD-II equipped vehicles. Although generic, the specific repair steps may vary depending on make/model. The Heated Oxygen Sensor (2) located rear of catalytic converter produces an output signal relative to oxygen storage capacity of catalytic converter.
What causes the p0140 OBD-II trouble code?
All our repairs are backed by our 12-month / 12,000-mile warranty. P0140 is the OBD-II generic code which indicates that the O2 sensor for Bank 1, Sensor 2 failed respond to the fuel cutoff or fuel enrichment signals by the Engine Control Module (ECM). What causes the P0140 code?
What does the code p0138 on a boxer engine mean?
Code P0138 is set when the downstream sensor sends too high of a voltage signal for an extended period of time. The bank one portion of the code indicates that the issue is on the side of the engine that houses the number one cylinder (only applies to engines with a ‘V’ or boxer configuration).
What does p0138 mean on a Jeep Wrangler?
Users have reported P0138 for the following makes: Jeep (especially on a Jeep Wrangler), Dodge, Toyota, Nissan, and Chevrolet. Code P0138 means that your powertrain control module (PCM) has detected that the voltage signal from the rear O2 sensor is too high. What is an Oxygen Sensor? All modern cars have at least two oxygen sensors.
What does the code p0138 mean on the O2 sensor?
What the P0138 code means. P0138 is the OBD-II generic code indicating the O2 sensor for bank 1 sensor 2 fails to have a lower voltage output below 1.2 volts for more than 10 seconds indicating a lack of oxygen in the exhaust stream.
What does P0420 mean on a catalytic converter?
Here’s the official definition of a P0420 trouble code: P0420 Catalyst System Efficiency Below Threshold (Bank 1). What the code is telling you is that the catalytic converter has failed an efficiency test. In 99.5% of the cases, this code means that the catalytic converter itself is bad and must be replaced.
How to diagnose the P0420 OBD2 trouble code?
How to Diagnose the P0420 Code 1 Connect an OBD2 Scanner and look for related trouble codes. 2 Check the live data to see the front and read O2 sensor signals. 3 Heat the engine and check the temperature at the front of the catalytic converter and then in the rear.
Code P0138 is set when the downstream sensor sends too high of a voltage signal for an extended period of time. The bank one portion of the code indicates that the issue is on the side of the engine that houses the number one cylinder (only applies to engines with a ‘V’ or boxer configuration).
What does a code p0172 on an OBD mean?
A code P0172 may mean that one or more of the following has happened: The MAF (Mass Air Flow) Sensor is dirty or faulty. Note: The use of “oiled” air filters can cause the MAF to become dirty if the filter is over-oiled. There could be a vacuum leak. There could be a fuel pressure or delivery problem
Why is my p0172 system too rich bank 1?
Check for an exhaust leak before the first oxygen sensor (this is unlikely to cause the problem, but it is possible) P0171 is showing on scanner but not a service light on , then after about 30 miles p0172 go’s active and turns service engine light on . Seems like it’s running fine ,but cannot get anyone to figure out the 172 code rich bank 1 .
What does it mean when your engine says p0128?
This means that the engine’s powertrain control module (PCM) has detected that the engine has not reached the required temperature level within a specified amount of time after starting the engine. Often, the intent of the P0128 code is to indicate a faulty thermostat (likely stuck in the open condition). Similar codes: P0125.
Can a p0128 coolant thermostat cause a burn?
When the engine is warm, the cooling system is pressurized and very hot and can cause burns or other personal injuries if you are not careful. Past experience indicates that the most likely solution for a P0128 is to replace the thermostat. However here are some suggestions on troubleshooting and repairing a P0128 OBD-II code:
What does fault code p0172 and p0175 mean?
P0172/P0175 Diagnostic Theory for Shops and Technicians. When a vehicle has the fault code P0172 and or P0175, it means that computer can no longer automatically adjust the mixture between air and fuel. Code P0172 applies to Bank 1 and P0175 applies to Bank 2.
What to do if your ECM says p0128?
If Nissan vehicle, check for Technical Service Bulletins (TSBs), as the ECM may need to be reprogrammed to correct the P0128 code Regardless of what vehicle year, make and model, it is advisable to check for TSBs because if there is a known fix set out by the automaker, it can save you time and money in the diagnosis and repair.