What do red flashing lights mean at a railway crossing?
STOP
TRAINS: Flashing red lights at a railroad crossing mean STOP! A full stop is always required. Make sure that there is no train traveling on the tracks and proceed.
What do railroad signal lights mean?
All railroads use the common red, yellow, and green aspects, although the indication of the yellow (approach) signal varies from road to road. Red means stop; green means proceed, and yellow means caution or approach, usually indicating that the next signal is red.
What triggers a railroad crossing light?
Level crossing signals are the electronic warning devices for road vehicles at railroad level crossings. The time interval may be controlled by a level crossing predictor, an electronic device which is connected to the rails of a railroad track, and activates the crossing’s warning devices (lights, bells, gates, etc.)
What must you do when red lights are flashing at a railway level crossing?
A red light at a railway level crossing always means stop. Once the lights have stopped flashing, check up and down the line, then proceed as long as there’s enough room on the other side of the crossing.
When approaching a railroad crossing without mechanical gates or lights you should?
When approaching a railroad crossing without mechanical gates or lights, you should:
- Cross the tracks as quickly as possible.
- Slow down to 15 mph and be prepared to stop if necessary.
- Stop on the tracks and look both ways.
- Approach the railroad tracks at 25 mph.
When you stop for a train at a railroad crossing if you are the vehicle closest to the rails?
Get the Correct ANSWER You must stop your vehicle within 50 feet but no less than 15 feet from the nearest rail of a railroad crossing. So always remember, stop no closer than 15 feet and no farther than 50 feet from the rail tracks.
What does a green railroad light mean?
go
When in doubt, remember that the colors for railroad lights are universally recognized. Similar to traffic lights, red means “stop,” yellow means “slow” or “caution,” and green means “go.”
What does a red signal mean on a train?
Danger/Stop
Single yellow – Caution. The driver must prepare to stop the train at the next signal. Flashing yellow – warns that a lower-speed diverging route is set, at a high speed turnout. Red – Danger/Stop.
What is the difference between a controlled and uncontrolled railroad crossing?
Railroads that have warning signs, red lights, and gates are called controlled railroad crossings. In some rural areas, uncontrolled railroad crossings are found with no signals, signs, or gates.
What does exempt mean at a railroad crossing?
Exempt signs are intended to inform drivers of commercial motor vehicles transporting passengers or hazardous materials that a stop is not required at certain designated railroad crossings, except when rail traffic is approaching or occupying the crossing or the driver’s view is blocked.
What should you do when coming up to a railway level crossing?
As you are coming up to a railway level crossing, slow down and be ready to stop if necessary, check each way before proceeding to cross, and only cross if there’s nothing blocking your path and there are no trains coming.
What does a red traffic light mean at a railroad crossing?
The lights are usually accompanied by a bell signal. Safety gates may or may not be present at the crossing. Flashing red traffic lights mean that a train is approaching. Motorists must not attempt to cross railway tracks when a red traffic light or bell signal is active.
When to cross while the red lights are flashing?
The foregoing requirements shall apply upon the occurrence of any of the following circumstances: (1) A clearly visible electric or mechanical signal device gives warning of the immediate approach of a railroad train. (2) A crossing gate is lowered or a flagman gives or continues to give a signal of the approach or passage of a railroad train.
Why does a train have to stop for a red signal?
Railroads also came up with a stop and proceed indication, which at least allowed the train to keep moving after coming to a complete stop, and probably saving a little bit of time. Restricting speeds are usually around 15MPH, but can be anything from 10 to 20MPH, depending on the railroad. Red / Stop: Trains must stop for a red signal.
Can a car cross a red traffic light?
Motorists must not attempt to cross railway tracks when a red traffic light or bell signal is active. Stay put, even if the warning light keeps flashing yet no train appears.