What could cause fuse to keep blowing from fuel pump Chev?
In April I replaced a fuel pump in my S10. When they replaced it , it blew a 20 amp fuse. They put in new fuse and it ran fine till this week. 5 months later. The fuel pump was bad and was replaced under warranty. It continues to blow fuse and they can’t figure out what the problem is. Any suggestions? My car has 160000 miles.
When did I replace the fuel pump in my S10?
In April I replaced a fuel pump in my S10. When they replaced it , it blew a 20 amp fuse. They put in new fuse and it ran fine till this week. 5 months later. The fuel pump was bad and was replaced under warranty.
Can a fuel pump overload cause a problem?
If not, check the other loads on the fuel pump circuit as those other loads could be causing the problem (the overload). To check that refer to wiring diagram in Factory Service Manual.
Why does the fuel pump fuse keep blowing?
The fuse that is blowing is the one that operates the relay, not the pump circuit. – the relay always has power (key on) and the ECM switches the ground. Old school method I always use in these instances is replace the fuse with a higher amp re-setting fuse like on electric window motors or electric seats!
Where is the fuse on the fuel pump?
Everytime I turn the ignition on, I blow the fuse. The fuse is located in the slot marked ECMI. How do I find out if it is the pump, the relay, or anything else? I am assuming there is a short somewhere. I thought maybe I pinched a wire and am arcing out somewhere.
What happens when a fuel pump relay goes bad?
If the fuel pump relay has an issue while the vehicle is operating it will cut off power to the fuel pump, which will cause the engine to stall. A faulty relay may allow the vehicle to be restarted a short while later, while a completely failed relay will not.
Where do you find the fuel pump relay?
When you shut off the ignition, it powers down the fuel pump. In most vehicles, the fuel pump relay can often be found in the fuse box in the engine bay, which is usually a long black box which contains fuel pump relay along with various other fuses and relays.
What causes a circuit breaker to blow a fuse?
Any faulty wiring or connected parts risk a power fault (surge), which trips a circuit (or blows a fuse). So, again, the problem is not that the circuit breaker (or fuse) didn’t do its job but rather that there was faulty equipment.
How can you tell when a fuse has been blown?
You might be wondering, then, how to tell if a fuse is blown–an actual fuse, that is. You will see that the fuse has melted, and there might be charring on the panel. A true fuse typically consists of a piece of metal, most commonly an encased wire, that actually melts when overheated. This is what stops the fault (aka “short” or “power surge” ).
What should I do if I Blew my Fuse?
The Fix: Make sure the faulty device is unplugged and there is no damage to the outlet. First, test the circuit. Then check for any damage on or around the electrical panel. If you see any damage, call an electrician before doing anything else with it. If there is none, flip the breaker switch back to its operating position.
Fuse #24 (20 amp) is Fuel pump relay output to fuel pump. Fuse #19 (10 amp) supplies 12 volts direct to the PCM. If the fuse is blowing, it has to be because there is too much of a current draw somewhere in the circuit.
Why is the fuse not blowing on my relay?
Replaced relay due to no start, vehicle started but acted as if cold circuit was not working. Drove for a few days like that and then the ASD control fuse (not the 30 amp) started blowing. Im back to square one.. Now Fuse is not blowing but the new relay is now chattering. Please help.
Why is the fuse blowing on the ASD relay?
If the fuse is blowing, it has to be because there is too much of a current draw somewhere in the circuit. The purpose of the ASD relay is to cut the power to the fuel pump if there is no Crank signal such as in the case of an accident.
What are the fuses on the fuel pump relay?
Fuse #12 (10amp) provides 12 volts to the coil side of both the relays and the ignition switch. Fuse #6 (30 amps) supplies 12 volts to the output side of the relay. Fuse #16 (15 amp) from the relay output to the Oxygen Sensors and Fuse #26 (15 amp) relay output to the PCM. Fuse #24 (20 amp) is Fuel pump relay output to fuel pump.
What causes fuel pump to draw more current than intended?
There is also the possibility of a physical (mechanical) restriction in the fuel pump tubing, filter and/or pick up causing the motor to overload and draw more current than intended. That’s why you should measure the actual current draw of the pump in normal operation to rule that out.
What causes the fuse to blow on a fuel pump?
I would start at the fuel pump itself. If the fuse blows as soon as you turn on the key, undo the connector at the tank to the pump and put in a new fuse. Try it again, if the fuse pops then your short is before that point likely a chafed wire on the body. If the fuse stays good then the problem is in the pump harness or the fuel pump itself.
What happens when the fuel pump goes out in a Jeep Wrangler?
There are physical signs that you can feel when your Wrangler’s fuel pump is going out. Before taking anything apart, check to see if your engine’s computer has any trouble codes saved in it. The engine may throw a P0087 trouble code. This trouble code detects that the fuel rail/system pressure is too low.
What are the symptoms of a bad fuel pump?
Also, the symptoms are almost exactly the same as bad/clogged fuel filter. Here are the most common symptoms of a bad fuel pump in your Jeep Wrangler: One of the most common signs that a fuel pump is going bad is a whining sound. The whining sound can indicate that the fuel pump is going out before there are any performance based issues.
Where does the fuel pump go in a car?
In modern fuel injected vehicles, the fuel pump sits right in the fuel tank and “pushes” the gasoline to the fuel rail (s). It is in the fuel tank because “pushing” fuel to the fuel rail is easier than “pulling” the fuel, which is what an inline pump would do.
What to do if your fuel pump is not working?
So if your vehicle isn’t starting and you suspect a fuel pump problem, here are some steps to follow to confirm your suspicions. Another ‘quick’ test is to bang on the fuel tank and then try and start the engine. Sometimes this works, just don’t bang too hard, you could damage something.
In April I replaced a fuel pump in my S10. When they replaced it , it blew a 20 amp fuse. They put in new fuse and it ran fine till this week. 5 months later. The fuel pump was bad and was replaced under warranty. It continues to blow fuse and they can’t figure out what the problem is. Any suggestions? My car has 160000 miles.
Why is my fuel pump relay outside the fuse box?
If it’s located inside the engine bay, which can get hot from the engine’s heat, the heat can impede the relay’s performance. In addition, in the rare cases where you will find the relay placed in the engine bay but outside the fuse box, it will be exposed to heat plus dust and dirt.
What happens when a fuel pump goes bad?
The engine turns off if the combustion chamber’s fuel is inadequate or doesn’t have the proper pressure. The part that ensures none of this happens is the fuel pump, and it cannot work perfectly if the fuel pump relay develops any issues. A faulty fuel pump relay can also cause the engine not to start at all and be completely dead.
How many pins does a fuel pump relay have?
The fuel pump relay does often have 4 pins, and in this case, it is often easy. If your relay has more pins and not the same numbers mentioned here, you need to check a wiring diagram. Lift it and check under it for the numbers 30, 85, 86, and 87. If you locate these numbers, you can put the fuel pump relay back.
When does a fuel pump relay go bad?
If you’re lucky and your car restarts after a short while, your fuel pump relay is faulty, which requires immediate inspection. The fuel relay may be the culprit if the car suddenly seems to lose power while driving, or slowing down with no apparent reason.
Everytime I turn the ignition on, I blow the fuse. The fuse is located in the slot marked ECMI. How do I find out if it is the pump, the relay, or anything else? I am assuming there is a short somewhere. I thought maybe I pinched a wire and am arcing out somewhere.
What causes a fuel pump to stop working?
However, this can happen due to several other reasons, such as a choked fuel filter, so you should always properly diagnose your car before replacing any parts. If the fuel pump relay may have any bad solderings inside it, it might suddenly lose the relay connection and stop delivering power to the fuel pump.
What are the symptoms of a bad fuel pump relay?
A bad fuel pump relay can cause many different symptoms. Here are the most common ones The fuel pump relay is an important component of the fuel system of your vehicle. The fuel pump relay gives the fuel pump power when it is time to build up fuel pressure in the rail.
If not, check the other loads on the fuel pump circuit as those other loads could be causing the problem (the overload). To check that refer to wiring diagram in Factory Service Manual.
Where is the fuel pump on a Pontiac Grand Am?
Check in the engine compartment fuse box, it should be near the battery under the hood. The cover should be pretty easy to remove. The fuel pump should be connected through a fuse in slot 48. If that fuse looks good, then you may want to check the fuel pump relay (also inside the engine compartment fuse box).
Why is my fuel pump reset button not working?
Anything from factory security system locking you out, bad fuse/relay, clogged fuel filter,faulty fuel pump, oil sending unit/crank sensor failure, clogged catalytic converter, failing electronic ignition, ECM/PCM,etc.,etc. As a first step best to see if there are any stored trouble codes that could point directly to the fault.
Check in the engine compartment fuse box, it should be near the battery under the hood. The cover should be pretty easy to remove. The fuel pump should be connected through a fuse in slot 48. If that fuse looks good, then you may want to check the fuel pump relay (also inside the engine compartment fuse box).
Why is there no power to the fuel pump?
Confirming power to the fuel pump (with a multimeter) also verifies that the fuel pump has failed and needs to be replaced. If no voltage is present, as your helper cranks the engine, then the cause of no fuel condition is due to either a bad fuse, fuel pump relay.
What happens when the fuel injector fuse is blown?
It was driving fine, and then suddenly the engine died shortly after exiting the freeway. Fuel pump seems to be fine, but the fuel injector fuse is blown and when replaced, blows again. Clicking this will make more experts see the question and we will remind you when it gets answered. You can’t post conmments that contain an email address.
The engine may still crank when the key is turned, however it will not be able to start due to lack of fuel. This symptom can also be caused by a wide variety of other issues, so having the vehicle properly diagnosed is highly recommended. 3. No noise from the fuel pump
Anything from factory security system locking you out, bad fuse/relay, clogged fuel filter,faulty fuel pump, oil sending unit/crank sensor failure, clogged catalytic converter, failing electronic ignition, ECM/PCM,etc.,etc. As a first step best to see if there are any stored trouble codes that could point directly to the fault.
What to do if your fuse keeps blowing?
Don’t wiggle wiring harnesses around in hopes of getting it to not blow another fuse because then there’s no defect to find. Once it is in the defective state, insert a pair of spade terminals in place of the blown fuse, then use a pair of jumper wires to connect them to a 12 volt light bulb.
What does a 20 amp fuel fuse do?
2004 chrysler sebring, 20 amp start/fuel fuse blows, what does… Battery is good. No radio, no wipers. Fan works and lights Battery is good. No radio, no wipers. Fan works and lights work but I get nothing when I try to start it. … read more No degree but have level 3… Vocational, Technical or Tra… 20 amp fuse for START/FUEL keeps shorting out.
In April I replaced a fuel pump in my S10. When they replaced it , it blew a 20 amp fuse. They put in new fuse and it ran fine till this week. 5 months later. The fuel pump was bad and was replaced under warranty.
Don’t wiggle wiring harnesses around in hopes of getting it to not blow another fuse because then there’s no defect to find. Once it is in the defective state, insert a pair of spade terminals in place of the blown fuse, then use a pair of jumper wires to connect them to a 12 volt light bulb.
What happens when a fuse blows on an ignition switch?
Insert a new fuse into the holder and turn the key to the run position. Turn the key off and pull out the fuse to see if it blew. If the fuse blows. When you turn the key to the run position, an internal ignition switch contact sends current from the B terminal on the ignition switch to the A1 terminal to energize the blue wire.
Where are the fuse blocks on a GMC TopKick?
GMC Topkick (2006) – fuse box diagram Posted on 1 January 201725 October 2018by admin GMC Topkick (2006) – fuse box diagram Year of production: 2006 Instrument Panel Fuse Block There are two instrument panel fuse blocks located behind the instrument panel on the passenger’s side of the vehicle.
How does a Mahindra front loader shut down?
It’s about a 23 HP diesel front loader by Mahindra Shuts down with a key. I’ll check the fuel pump. Stay tuned The fuel filter is between the tank and the fuel pump. The fuel filter/ shutoff is gravity fed from the tank. The outline from the filter goes to the inline of the fuel pump.
Why does my Mahindra Tractor have black smoke?
Didn’t seem necessary Speaking of smoke in the stack. It does send a lot of black smoke out the exhaust while trying to start. oh wow ok that changes things a lot! that tells us that the engine is getting fuel and the electrical part of the system is operating correctly because its turning the pump on.
Why is my 2015 Mahindra tractor not starting?
I have a Mahindra 2015 tractor. I’m having starting problems. The engine just won’t fire. I have a Mahindra… I have a Mahindra 2015 tractor. I’m having starting problems. The engine just won’t fire. I thought it was the starter and battery but I’ve changed them both. Also purchased new battery cables.
How do you clean a fuel pump relay?
Since any debris will affect the fuel pump relay’s performance, you should regularly inspect and clean it when necessary. The fuel pump relay is an electrical car part, thus be extremely careful when handling a relay. First, take off the relay and use the blower to blow off dirt and dust for about 1-2 minutes.