What can I do with an intake manifold removal?
Removal of the Intake Manifold (also called the plenum) is necessary or helpful to perform several jobs on the VG30DE (TT), such as: Fuel Injector Replacement (as an alternative to the Dremel Method ). Valve Cover re-seal. PCV reroute/delete. Throttle Body Coolant line bypass/removal. EGR bypass/removal.
How to remove a coolant line from an intake manifold?
Remove the Intake Manifold. Being careful not to damage the plenum, set it upside-down to gain access to the piping attached to the underside. Remove the 4 x 10mm bolts (Items 1) securing the hard lines to the plenum. Remove the millions of rubber lines (Items 2) connecting to these hard-lines and ports.
How do you remove an intake manifold in a PB Blaster?
One common way to remove the intake manifold is performed when you have the transmission removed for another job (such as a clutch/flywheel replacement or upgrade). Spray all EGR bolts in PB Blaster and wait a day! After removing the transmission, remove the upper intake pipes (2 for the NA, 4 for the TT).
What kind of gasket do you need for an intake manifold?
Intake Manifold Gasket (upper plenum to lower plenum) (Part #14033-30P02). Required. This is a paper gasket that is destroyed upon removal and must be replaced. OEM Nissan is recommended (and is very cheap). Balance tube O-ring set (if they haven’t been replaced yet). 8mm, 10mm, 12mm, 12mm (deep) sockets. Ratcheting driver for sockets.
How do you remove an intake manifold from a car?
Disconnect the fuel lines that go from the Fuel Dampener to the Fuel Rail, and from the Fuel Rail to the FPR (circled in red). Remove the bolts that hold the Fuel Dampener and Fuel Pressure Regulator to the plenum. (2x10mm for each). Remove the 3x10mm bolts that secure the upper fuel gallery to the plenum. Remove the fuel gallery.
Where is idle air adjusting unit on Nissan 300ZX?
Remove the idle air tube running the length of the driver side of the plenum. Pull the clamps back at the front on the curved hose and on the rear where it goes into the idle air adjusting unit on the back corner of the plenum. The tubing might have the wiring harness clipped to it. Disconnect the harness and remove the tubing.
Intake Manifold Gasket (upper plenum to lower plenum) (Part #14033-30P02). Required. This is a paper gasket that is destroyed upon removal and must be replaced. OEM Nissan is recommended (and is very cheap). Balance tube O-ring set (if they haven’t been replaced yet). 8mm, 10mm, 12mm, 12mm (deep) sockets. Ratcheting driver for sockets.
Where are the throttle cables on a Nissan 300ZX?
1. 3. Disconnect throttle cables by loosening the front nuts on the bracket (2 x 14mm nuts) (yellow dot in 2. ), then swing the cables out of the throttle body control rod cable ways in the front of the engine. The cables are held in place in three locations along the way to the plenum.
Removal of the Intake Manifold (also called the plenum) is necessary or helpful to perform several jobs on the VG30DE (TT), such as: Fuel Injector Replacement (as an alternative to the Dremel Method ). Valve Cover re-seal. PCV reroute/delete. Throttle Body Coolant line bypass/removal. EGR bypass/removal.
Where are the fasteners on an intake manifold?
Locate and remove all the fasteners attaching the intake to the engine. If your engine is a V type, they will probably all be on top. In that case, check your workshop manual, as there will be a recommended sequence for loosening the bolts.
Is it safe to replace an intake manifold gasket?
Replacing a manifold gasket can be a daunting job, especially because of the danger of making a small mistake that can ruin your engine. If you don’t feel confident doing the job yourself, have one of YourMechanic’s certified technicians come to your home or business and perform a intake manifold gasket replacement for you.
When to replace coolant in an intake manifold?
If the coolant you drained out is more than two years old, replace it with fresh coolant. Keep pouring until coolant runs out of the bleeder or the hose that you disconnected. Step 2: Set the car’s heater on high.