What are the torque specs for a Hyundai Tiburon?

size M10 bolts – 18 foot pounds of torque PLUS turn 60 degrees PLUS turn 60 degrees again. size M12 bolts – 22 foot pounds of torque PLUS turn 60 degrees PLUS turn 60 degrees again. Please note, your Deposit doesn’t constitute a payment.

What kind of torque does a Hyundai Sonata have?

BALL JOINT BOLT 43-52 (58-71) BALL JOINT ARM BOLTS EXCEL & SCOUPE (1991-94) 43-52 (58-71) BEARING CENTER BRACKET (SONATA) 26-33 (34-45) BRAKE CALIPER-TO-KNUCKLE (SONATA) 58-72 (78-98) STRUT BAR BOLT 75 (102) TIE ROD NUT ELANTRA, EXCEL, & SCOUPE 11-25 (20-34) SONATA 17-25 (23-34) WHEEL LUG NUT ALUMINUM WHEELS

How to read torque specs 2.0 beta 1?

Anyone got a link for torque specs and tightening sequence for beta 1 2.0…I can’t find any….. Found the torque stilll need sequence… Did you find the recommended reading relevant to this discussion?

How to properly torque outer tie rod end ( front driver )?

So I’ve replaced the tie rod end as mentioned. The issue is I can’t determine how much I’m torquing it down. The end the bolt goes onto just spins around unless I use an impact wrench but I cant tell how tight it is. Should i just impact it til its snug?

What should the torque be on a torque table?

Torque specifications are shown either as an exact figure, or a specific range. Follow any special instructions or multi-step directions carefully to assure correct final torque. There may be different specifications for different size bolts, bolts in different positions, tightening bolts in several stages, or a cold engine vs. a warm engine.

Where can I find the latest torque specs?

Find the most up-to-date torque spec listings in electronic format. FelPro-Only.com is your convenient source for advanced sealing information. It’s the place to learn and share “tricks of the trade,” find proper diagnosis and installation instructions, and enjoy easy access to parts reference.

What should the torque be on a cylinder head bolt?

The manufacturer usually stipulates that you must tighten the bolts in incremental steps. For example, suppose the final torque on a bolt is 40 foot-lbs. The manufacturer may state to bring all the bolts to 10 foot-lbs. first, following the torque sequence. In the second step, bring the torque to 20 foot-lbs.

How much torque does a Hyundai Elantra head bolt have?

SOURCE: Correct torque on cylinder head bolts for Hyundai Elantra 1.8GLS You have two bolt sizes the shorter or smaller of the two sizes is called M10 the torque is 22ft lbs +65 degrees +65 degrees again The larger of the two bolts is called a M12 the torque for these are 26ft lbs +65+65.

What are the torque specifications for an internal combustion engine?

Internal combustion engines run the gamut from small handheld model airplane units to large ship engines. For head bolts, no “one size fits all” approach to the torque specifications applies. One technical manual at Brigham Young University states that you must follow the manufacturer’s instructions.

Where can I find the head torque specs?

This is straight from “All Data”. If you need it, I have all the specifications for the Cylinder Head Assembly & Valves also. PM me with you email and I can get the info to you.

What’s the 0-60 mph time of a Hyundai Tiburon?

The 2.0L produces a 0–60 mph time of ~8.3, with a 1/4 mile time of ~16 seconds. In 1998 the Tiburon lost its weaker 1.8L engine, giving both models the 2.0L. All versions of the Tiburon manufactured from 1996 to 2002 are known as “RD” Tiburons. The MacPherson strut suspension was co-developed with Porsche .

How much does a Hyundai Tiburon cost on the road?

The front carpet mats were inlaid with rectangular silver-coloured “Coupe F2” badges. According to the Hyundai Coupe F2 brochure, total on-the-road price was £17,999 (as of July 1998). Two further items were available free to the first five-hundred Hyundai Coupe F2 buyers.

Navigation